FLIR EXTECH INSTRUMENTS PQ34-12 Manuel utilisateur

User's Guide

1200A Current Probe Set

Model PQ34-12

www.calcert.com [email protected]1.888.610.7664 0

PQ-12-EU-EN V1.0 01/12

Introduction

Congratulations on your purchase of this Extech Current Probe Set. A set of three 1200A current

probes designed to be used with the Extech PQ3450 or PQ3470 Power Analyzers. These probes

are shipped fully tested and calibrated and, with proper use, will provide years of reliable service.

Safety

This symbol, adjacent to another symbol or terminal, indicates the user must refer to the

manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages

may be present

Double insulation

Cautions

Read and understand this user manual before operating the meter.

Improper use of this meter can cause damage, shock, injury or death.

Inspect the condition of the leads and the meter itself for any damage before operating the

meter.

Use great care when making measurements if the voltages are greater than 25VAC rms or

35VDC. These voltages are considered a shock hazard.

Do not attempt to measure Current that exceeds specified limits

Do not operate this instrument in wet or dusty environments.

Do not operate this instrument in the presence of combustible or explosive gas

Do not touch exposed metal parts or unused terminals.

Use protective gloves near high current or voltage circuits.

If the equipment is used in a manner not specified by the manufacturer, the protection provided

by the equipment may be impaired.

www.calcert.com [email protected]1.888.610.7664 0

PQ-12-EU-EN V1.0 01/12

Probe Description

1. Current Sensing Jaws

2. Jaw Trigger

3. 1200A-200A-20A range switch

4. Signal output plug ( +, red )

5. Signal output plug ( -, black )

6. DCV power plug

Operation

1. Connect the “A1” signal output cables to the matching input sockets

on the top of the analyzer.

2. Connect the “A1” power cable to the matching power socket on the

top of the analyzer.

3. Set the "1200A-200A-20A” range switch to the range appropriate for

the application.

Note: Make sure the range set on the clamp matches the range

set in the analyzer.

4. Connect the “A2” and “A3” clamps as above, if needed.

5. Press the "Trigger" to open the jaws and clamp around a single

conductor.

6. Power on the power analyzer

www.calcert.com [email protected]1.888.610.7664 0

PQ-12-EU-EN V1.0 01/12

Specifications

Measurement ranges 20A, 200A and 1200A, switch selectable

Output sensitivity 10mV/A on the 20A range

1mV/A on the 200A range

0.1mV/A on the 1200A range

Output coupling AC coupled.

Accuracy (50/60Hz) ± 1% F.S. @ 23 ± 5°C

Frequency range 45 to 400 Hz.

Phase error (50/60Hz) < ± 1°

Minimum load 100 K ohm for specified accuracy

Enclosure material UL 94-V0 rated

Safety IEC 1010, Category III 600V

Power Supply 8V± 1V (supplied from meter)

Max. Jaw Open Size 50 mm (2.0 inch) Dia.

Operating Temperature 0°C to 50°C (32°F to 122°F)

Operating Humidity Less than 80% RH

Dimension 210 x 64 x 33 mm. (8.3 X 2.5 X 1.3”inch )

Cable length : 4 meters (13.17 feet)

DC plug size : 5.5 mm x 2.5 mm DIA.

Weight 490 g (1.08 LB)

Safety For indoor use and in accordance with the requirements for

indoor use, double insulation to IEC1010-1 (2001):

EN61010-1 (2001) Overvoltage Category III 600V,, Pollution

Degree 2.

www.extech.com

www.calcert.com [email protected]1.888.610.7664 0

Autres manuels FLIR Instrument de mesure

FLIR

FLIR EXTECH INSTRUMENTS PQ3450 Manuel utilisateur

FLIR

FLIR TA50 Manuel utilisateur

FLIR

FLIR EM54 Manuel utilisateur

FLIR

FLIR CM174 Manuel utilisateur

FLIR

FLIR Extech Instruments PQ34-2 Manuel utilisateur

FLIR

FLIR Extech Instruments RH520A-240 Manuel utilisateur

FLIR

FLIR identiFINDER R300 Manuel utilisateur

FLIR

FLIR Extech Instruments EX840 Manuel utilisateur

FLIR

FLIR Extech 380926 Manuel utilisateur

FLIR

FLIR Extech 380941 Manuel utilisateur

FLIR

FLIR CM42 Manuel utilisateur

FLIR

FLIR Extech Instruments 480823 Manuel utilisateur

FLIR

FLIR MR55 Manuel utilisateur

FLIR

FLIR EXTECH RH520 Manuel utilisateur

FLIR

FLIR Extech HDV-TX2 Manuel utilisateur

FLIR

FLIR CM65 Manuel utilisateur

FLIR

FLIR DM284 Manuel utilisateur

FLIR

FLIR VS80 KIT Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX2 Manuel utilisateur

FLIR

FLIR EXTECH HDV-WTX1 Dimensions

FLIR

FLIR MR160 Manuel utilisateur

FLIR

FLIR Si124 Manuel utilisateur

FLIR

FLIR TA60 Manuel utilisateur

FLIR

FLIR Extech 407760 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur