F&F BIS-411B-LED Manuel utilisateur
- 1 -
BIS-411B-LED
Bistable relay
Electronic bistable pulse relay BIS-411B-LED allows switching on
or off the lighting or other device from several different points by
parallel connected, momentary (bell) control switches.
A push button on the housing enables direct control of the cir-
cuit without the need to trigger external buttons.
The receiver is switched on after a current pulse caused by pres-
sing any momentary (bell) button connected to the relay. After
the next pulse, the receiver will be switched off. The relay does
not have a "memory" of the contact position, which means in
the event of a power failure and its subsequent return, the relay
contact will be set to "off". This prevents the controlled receivers
from being switched on automatically without supervision after
a prolonged power failure. The button on the housing performs
exactly the same function as the external button connected to
the terminals of the device.
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71
www.fif.com.pl; e-mail: biuro@fif.com.pl
Do not dispose of this device in the trash along with other waste! According to the Law on
Waste, electro coming from households free of charge and can give any amount to up to
that end point of collec� on, as well as to store the occasion of the purchase of new equip-
ment (in accordance with the principle of old-for-new, regardless of brand). Electro thrown
in the trash or abandoned in nature, pose a threat to the environment and human health.
- 2 -
The "LED" version of the relay is equipped with a contact
designed to cooperate with receivers with high starting
current, such as: LED fluorescent lamps, ESL fluorescent
lamps, electronic transformers, discharge lamps, etc.
1.Disconnect the power supply.
2.Fix the relay on a rail in the control box.
3.Connect the power wires to terminals 1-3 according to the se-
lected relay control option (control pulse L or N).
4.Momentary switches connected in parallel, connect to termi-
nal 6 and to the wire to which terminal 3 is connected.
5.Connect the powered receiver in series to terminals 11-12.
The maximum total backlight current of all connected
buttons must not exceed 5 mA.
BIS-411B-LED can work with backlit buttons.
Mounting
- 3 -
Wiring diagram
- 4 -
1-3 power supply of the relay 165÷265 V AC
6 control input
11-12 NO contact (active)
- 5 -
power supply 165÷265 V AC
contact separated 1×NO
maximum load current (AC-1) 16 A (120 A/20 ms)
control pulse current 5 mA
activation delay 0.1÷0.2 s
power supply indication green LED
activation indication red LED
mechanical life of the button 10⁶ cycles
power consumption
stand-by 0.15 W
on 0.6 W
terminal 2.5 mm² screw terminals
tightening torque 0.4 Nm
working temperature -25÷50°C
dimensions 1 module (18 mm)
mounting on TH-35 rail
ingress protection IP20
Technical data
- 6 -
tungsten halogen fluorescent energy-saving LED
2000 W 1250 W 1000 W 500 W 250 W
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE. The CE Declaration of Conformity, along
with the references to the standards in relation to which confor-
mity is declared, can be found at www.fif.com.pl on the product
page.
Power table
Warranty
CE declaration
E211117
Table des matières
Autres manuels F&F Relais
F&F
F&F BIS-408i Manuel utilisateur
F&F
F&F OM-630 Manuel utilisateur
F&F
F&F BIS-412M 24V Manuel utilisateur
F&F
F&F FW-R1P Manuel utilisateur
F&F
F&F BIS-408 Manuel utilisateur
F&F
F&F BIS-411i Manuel utilisateur
F&F
F&F BIS-410-LED Manuel utilisateur
F&F
F&F 5908312592389 Manuel utilisateur
F&F
F&F BIS-410 Manuel utilisateur
F&F
F&F BIS-410-24V Manuel utilisateur
F&F
F&F PK-3P Manuel utilisateur
F&F
F&F PCS-506 Manuel utilisateur
F&F
F&F PK-1P Manuel utilisateur
F&F
F&F FW-R2D Manuel utilisateur
F&F
F&F PP-2Z Manuel utilisateur
F&F
F&F PCS-517.2 Manuel utilisateur
F&F
F&F PK-2P Manuel utilisateur
F&F
F&F 5908312595533 Manuel utilisateur
F&F
F&F PK-2Z-LED 24 V Manuel utilisateur
F&F
F&F BIS-419-LED Manuel utilisateur
