Faber Veil Manuel utilisateur
Libretto di Istruzioni
Instructions Manual
Bedienungsanleitung
Manual de instrucciones
Instrukcja Obsâugi
ɋɮɥɩɝɩɟɬɭɝɩ ɪɩ ɸɥɬɪɦɮɛɭɛɱɣɣ
ǽȗȥıțȢȔİțȡ ȡİșȗțȬȟ
Käyttöohje
Brugsvejledning
Bruksanvisnin
g
Priroÿnik za uporabo
Príruÿka na obsluhu
Uputstva za Korištenje
Uživatelská Pøíruèka
Ƀɨɬɭɫɮɥɱɣɣ ɋɵɥɩɝɩɟɬɭɝɩ
ΐϴϛήΘϟ Ϟϴϟ
Ω
EN 1
14
RECOMMENDATIONS AND SUGGESTIONS
The Instructions for Use apply to several versions of this appliance.
Accordingly, you may find descriptions of individual features that do not
apply to your specific appliance.
INSTALLATION
! The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation.
! The minimum safety distance between the cooker top
and the extractor hood is 650 mm (some models can
be installed at a lower height, please refer to the
paragraphs on working dimensions and installation).
! Check that the mains voltage corresponds to that
indicated on the rating plate fixed to the inside of the
hood.
! For Class I appliances, check that the domestic
power supply guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm. The route of the flue must be as short as possible.
! Do not connect the extractor hood to exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
! If the extractor is used in conjunction with non-
electrical appliances (e.g. gas burning
appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the
backflow of exhaust gas. The kitchen must have
an opening communicating directly with the open
air in order to guarantee the entry of clean air.
When the cooker hood is used in conjunction with
appliances supplied with energy other than electric, the negative pressure in
the room must not exceed 0,04 mbar to prevent fumes being drawn back
into the room by the cooker hood.
! In the event of damage to the power cable, it must be replaced by the
manufacturer or by the technical service department, in order to prevent any
risks.
2°
EN 1
15
• If the instructions for installation for the gas hob specify a greater distance
specified above, this has to be taken into account. Regulations concerning
the discharge of air have to be fulfilled.
• Use only screws and small parts in support of the hood.
Warning: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards.
• Connect the hood to the mains through a two-pole switch having a contact
gap of at least 3 mm.
USE
• The extractor hood has been designed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making
sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored
during use: overheated oil can burst into flames.
• Do not flambè under the range hood; risk of fire.
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
EN 1
16
• •CAUTION: Accessible parts may become hot when used with cooking
appliances.”
MAINTENANCE
•Switch off or unplug the appliance from the mains supply before carrying out
any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• The Grease filters must be cleaned every 2 months of operation, or more
frequently for particularly heavy usage, and can be washed in a dishwasher.
• The Activated charcoal filter is not washable and cannot be regenerated,
and must be replaced approximately every 4 months of operation, or more
frequently for particularly heavy usage.
• Clean the hood using a damp cloth and a neutral liquid detergent.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
EN 1
17
CHARACTERISTICS
Dimensions
Components
Ref. Q.ty Product Components
1 1 Hood Canopy complete with: Controls, Light, Fan
unit, Filters
21 Telescopic chimney, made up of:
2.1 1 Upper Chimney
2.2 1 Lower Chimney
81 Air outlet grid D.150
91 Damper D.150-120
14 1 Hood Canopy Air Outlet Extension made up of 2
half-elements
Ref. Q.ty Installation Components
11 6 Wall Plugs
11a 2 SB 12/10 Wall Plugs
12a 6 Screws 4.2x44.4
12c 4 Screws 2.9x9.5
12e 4 Screws 2.9x6.5
Q.ty Documentation
1 Instruction Manual
EN 1
18
INSTALLATION
Drilling the Wall and Fixing the Brackets
650
455
75
240 240
200 200
Draw the following on the Wall:
• a Vertical line up to the ceiling or top surface, at the centre of the area in which the Hood is
to be fitted;
• a Horizontal line: 650 mm min. above the Hob;
• As shown in the drawing, mark a reference point 455 mm above the reference horizontal
line, and at a distance of 240 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking to ensure it is level.
• Drill the points marked using a ø 12 mm drill bit.
• Insert the wall plugs with screw and bracket 11a into the holes, tighten.
• As shown in the drawing, mark a reference point 75 mm above the reference horizontal line,
and at a distance of 200 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking to ensure it is level.
• Drill the points marked using a ø 8 mm drill bit.
• Insert the plugs 11 into the holes.
• Rest the Bracket 7.2.1 as indicated, 1-2 mm from the ceiling or surface above the hood, aligning
its centre (grooves) with the vertical reference line.
• Mark the centres of the holes in the bracket.
• Rest the Bracket 7.2.1 as indicated, X mm under the first bracket (X = height of the Upper
chimney provided), aligning its centre (grooves) with the vertical reference line.
• Mark the centres of the holes in the bracket.
• Drill the points marked using a ø 8 mm drill bit.
• Insert the plugs 11 into the holes.
• Fix the brackets using the screws 12a (4.2 x 44.4 ) provided.
EN 1
19
Fitting the Hood canopy
• Remove the Metal grease filter using the handles provided.
• Adjust the two screws Vr, in the brackets 11a, so that they are
at the start of their travel.
• Hook the hood body to the two brackets 11a.
• From the inside of the hood body, turn screws Vr to level the
hood body itself.
• Fasten the safety screws 12a.
• Replace the Metal grease filter.
Connections
AIR OUTLET - DUCTING VERSION
When installing the Ducting version, join the Hood to the outlet
duct using a rigid or flexible pipe ø150 - ø 120 selection of which
is at the discretion of the installation technician.
• Check that the pipe is properly inserted onto the Motor Unit
outlet.
• Fix the outlet pipe using suitable pipe clamps. The materials
required to do so are not provided.
AIR OUTLET – RECIRCULATION VERSION
• Join the 2 half-elements making up the pipe 14.
• Push the pipe 14 firmly until it is all the way in.
• Cut away the excess part with a tool.
• Fix the directional Grid 8 on the recycled air outlet, using 2
screws 12e (2.9 x 9.5) provided.
• Make sure that the Activated charcoal odour filter has been
fitted.
EN 2
20
Fitting the Chimney
Lift the 2 tabs formed on the Hood Canopy close to the
air outlet opening.
Upper chimney
• Open the two side pieces out slightly, hook them up
behind the brackets 7.2.1 and bring them back
together again until they are in contact.
• Fix them to the sides of the Brackets using 4 Screws
12c (2.9 x 9.5), provided.
Lower chimney
• Open out the two Chimney side flaps, hook them up
between the upper chimney and the wall and then
close them up again until they touch.
• Fix the lower part to the Hood canopy tabs at the
sides, using 2 screws 12c (2.9 x 9.5) provided.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole
switch having a contact gap of at least 3 mm.
• Remove the grease filters (see paragraph Mainte-
nance) being sure that the connector of the feeding
cable is correctly inserted in the socket placed on the
side of the fan.
EN 2
21
USE
T2
T1 L
T3
Control panel
BUTTON LED FUNCTIONS
T1 Speed On Turns the Motor on at Speed one.
Turns the Motor off.
T2 Speed On Turns the Motor on at Speed two.
T3 Speed Fixed When pressed briefly, turns the Motor on at Speed three.
Flashing Pressed for 2 Seconds.
Activates Speed four with a timer set to 6 minutes, after which
it returns to the speed that was set previously. Suitable to deal
with maximum levels of cooking fumes.
LLight Turns the Lighting System on and off.
Warning: Button T1 turns the motor off, after first passing to speed one.
EN 2
22
MAINTENANCE
Grease filters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
• The filters must be cleaned every 2 months of operation, or
more frequently for particularly heavy usage, and can be
washed in a dishwasher.
• Remove the filters one at a time by pushing them towards the
back of the group and pulling down at the same time.
• Wash the filters, taking care not to bend them. Allow them to
dry before refitting.
• When refitting the filters, make sure that the handle is visible
on the outside.
Activated charcoal filter (Recirculation version)
These filters are not washable and cannot be regenerated, and
must be replaced approximately every 4 months of operation, or
more frequently with heavy usage.
REPLACING THE ACTIVATED CHARCOAL FILTER
• Remove the metal grease filters
• Remove the saturated activated charcoal filter as shown (A).
• Fit the new filters (B).
• Replace the metal grease filters.
A
B
Lighting unit
Warning: This appliance is fitted with a white LED lamp classed
as 1M according to EN 60825-1: 1994 + A1:2002 + A2:2001
standards; maximum optical power emitted @439nm: 7µW. Do
not look directly at the light through optical devices (binoculars,
magnifying glasses…).
• For replacement contact technical support. ("To purchase con-
tact technical support")
Autres manuels pour Veil
1
Table des matières
Autres manuels Faber hotte de ventilation
Faber
Faber AXIA Manuel utilisateur
Faber
Faber Cylindra Isola Gloss Manuel utilisateur
Faber
Faber FABULA PLUS BK 90 Manuel utilisateur
Faber
Faber CRISTAL 24 Manuel utilisateur
Faber
Faber V-AIR Manuel utilisateur
Faber
Faber TCH04 Manuel utilisateur
Faber
Faber INCA HC SS Manuel utilisateur
Faber
Faber GALILEO SMART BK A600 + Kit LL H80 Manuel utilisateur
Faber
Faber STILO ISOLA/SP Manuel utilisateur
Faber
Faber Pixel BK A60 R Manuel utilisateur
Faber
Faber TRAT30SSV Manuel du propriétaire
Faber
Faber INCA SMART Manuel utilisateur
Faber
Faber TENDER Manuel utilisateur
Faber
Faber LINSPT301228 Manuel du propriétaire
Faber
Faber Magnum Manuel utilisateur
Faber
Faber 991.0536.838 Manuel utilisateur
Faber
Faber 630003950 Manuel utilisateur
Faber
Faber BELA30SS600-B Manuel utilisateur
Faber
Faber GLAM FIT 80 WH Manuel utilisateur
Faber
Faber INCA LUX INLX21SSV2 Manuel du propriétaire
