Extron electronics FOX T UWP 302 Manuel utilisateur

Product Category

FOX T UWP 302 • Installation Guide

CLASS 1 LASER PRODUCT, see FOX T UWP 302 User Guide at www.extron.com.

This guide provides instructions for an experienced installer to install and connect the 3-gang Extron FOX T UWP 302 Universal

Wallplate Transmitter and switcher. It can t into a wall or oor box.

NOTE: The FOX T UWP 302 is not compatible with the FOX 3G HD-SDI,

FOX 3G DVC, or FOX AV models.

WARNING: Risk of serious physical injury. The transmitter outputs continuous

invisible light, which may be harmful to the eyes; use with caution.

• Do not look into the ber optic cable connectors or into the ber optic cables

themselves.

• Plug the attached dust caps into the optical transceivers when the ber optic

cable is unplugged.

Planning

CAUTION: Risk of personal injury. Failure to check these items may result in personal injury.

ATTENTION: Failure to check the items listed below may result in property damage.

Check that the installation meets the building, electrical, and safety codes.

Installation

Step 1 —Preparing the Mounting Surface

a. Install a UL-listed electrical junction box according to the instructions of the manufacturer.

b. Secure cables with clamps or ties to provide strain relief (see Making Rear Panel Connections below for necessary cables).

c. Trim back and insulate shields with heat shrink.

ATTENTION: To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable

clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

Step 2 —Making Rear Panel Connections

AFiber optic connector — Connect a ber cable between the Tx port on the FOX T UWP 302

and the Rx port on a receiver.

To return serial data from the receiver to the FOX T UWP 302, connect a ber cable between

the Rx port on the transmitter and the Tx port on the receiver.

BRemote RS-232 and Alarm connector — For serial RS-232 control of the FOX T UWP 302,

connect the host device to the leftmost poles (Tx, Rx, and G) of this 5-pole captive screw

connector. For remote monitoring of the status of ber optic link 2, connect a custom

monitoring device to the rightmost poles (1 and 2) of this 5-pole captive screw connector.

CPower connector —Connect the provided 12 VDC external power supply to this 3.5 mm,

2-pole captive screw connector.

Step 3 —Mounting

DAttach the FOX T UWP 302 to the junction box with screws.

TIP: If necessary, configure the device before attaching the

decorator-style faceplate in the step below (see Remote Control on

the next page or the FOX T UWP 302 User Guide for more details).

EAttach the decorator-style faceplate to the FOX T UWP 302 with the provided

screws.

POWER

HDMI

HDCP

AUDIO INPUT

HDMI INPUT

COMPUTER INPUT

AUDIO

Flush with

Wall Surface

Scr

ews or Nails

Wall Stud

Wall Box

Mounting

Screws

(6 Plcs)

EEEEEEEEEE

DDDDDDDD

Rear Panel Connectors from the Side View

AAAAAAAAAA

BBBBBBBB

CCCCCCCC

FOX T UWP 302 • Installation Guide (Continued)

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

Inside India Only

+91-80-3055.3777

+91 80 3055 3737 FAX

Rev. B

04 17

Step 4 —Making Front Panel Connections

FConnect a source device to the HDMI connector.

TIP: Use an Extron LockIt®Lacing Bracket to secure

HDMI cables to the HDMI connector.

GConnect a video source to the Computer Input connector.

HConnect an audio source to the 3.5 mm TRS jack.

Operation

Remote Control

Connect a host device, such as a computer, to the mini-USB type B

cong port for serial control of the FOX T UWP 302. Use SIS commands or install the FOX Extenders Control Program

from the Extron Software Products DVD or check the Extron website, www.extron.com, for the latest version (see the

FOX T UWP 302 User Guide for remote control details).

Reset button

Press and hold the Reset button on the front panel to enter reset mode 1 or 5. If necessary, unscrew the screws

connecting the faceplate to the enclosure and remove the faceplate to access the Reset button.

Reset Mode Summary

Mode Activation Result Purpose/Notes

Factory Reset

(Mode 1)

Hold the Reset button down while

applying power to the device.

NOTE: After a mode 1 reset,

update the device with the

latest firmware version. DO NOT

operate the firmware version

that results from this mode

reset.

zThe device reverts to the factory default rmware.

zAll user les and settings (audio adjustments,

audio input selection, input selection,

auto-switch mode, picture adjustments, and

input video format) are maintained.

Use mode 1 to roll back

to factory rmware for

a single power cycle if

an incompatibility issue

arises.

Reset to Factory

Defaults (Mode 5)

Hold the Reset button down for about

9 seconds or until the Power LED

blinks three times. Then press the

Reset button momentarily

(for <1 second) within 1 second.

zMode 5 performs a complete reset to factory

defaults except for rmware.

zResets all user modiable congurations to

default values including real-time adjustments.

zThe power LED blinks 4 times in quick

succession during the reset.

Use mode 5 to start over

with conguration or

uploading.

NOTE: This is

equivalent to SIS

command ZXXX.

Indicators

Link 1 and Link 2 LEDs —Light to indicate ber light presence.

Power LED —Lights when the device receives 12 V from an external power supply.

PC LED —Lights when PC input is detected.

HDMI LED —Lights when HDMI input is detected.

HDCP LED —Lights if the HDMI input signal is HDCP-encrypted.

Audio LED —Lights when the device detects audio with the selected input. If the selected input has an analog audio

signal above -44 dBV, the Audio LED lights immediately, but turns off only after the audio signal level drops below the

threshold continuously for 10 seconds. If the selected input has digital embedded audio, the Audio LED lights and

remains lit as long as the digital audio signal is detected.

POWER

HDMI

HDCP

AUDIO

CONFIG

RESET

LINK 1

LINK 2

LINK 1

LINK 2

HDMI INPUT

AUDIO INPUT

COMPUTER INPUT

POWER

RESET

CONFIG

HDMI

HDCP

AUDIO

FFFFFFFFFF

GGGGGGGG

HHHHHHHH

Autres manuels pour FOX T UWP 302

Table des matières

Autres manuels Extron electronics Émetteur

Extron electronics

Extron electronics DTP2 T 201 D Manuel utilisateur

Extron electronics

Extron electronics FOXBOX T HD-SDI Manuel utilisateur

Extron electronics

Extron electronics PowerCage MTP AV Series Manuel utilisateur

Extron electronics

Extron electronics ExSens Manuel utilisateur

Extron electronics

Extron electronics DTP T HWP D Series Manuel utilisateur

Extron electronics

Extron electronics DTP T USW 233 Manuel utilisateur

Extron electronics

Extron electronics XTP T UWP 202 4K Manuel utilisateur

Extron electronics

Extron electronics DVI 201xi TX Manuel utilisateur

Extron electronics

Extron electronics DTP T EU 4K 331 Manuel utilisateur

Extron electronics

Extron electronics FOXBOX 4G Tx Manuel utilisateur

Extron electronics

Extron electronics XTP T VGA Manuel utilisateur

Extron electronics

Extron electronics USB Extender Plus Series Manuel utilisateur

Extron electronics

Extron electronics PVT RGB D Plus Manuel utilisateur

Extron electronics

Extron electronics DTP2 T 203 Manuel utilisateur

Extron electronics

Extron electronics XTP FT HD 4K Manuel utilisateur

Extron electronics

Extron electronics PowerCage FOX 4G Tx VGA Manuel utilisateur

Extron electronics

Extron electronics DTP T HWP 232 D Manuel utilisateur

Extron electronics

Extron electronics XTP T VGA Manuel utilisateur

Extron electronics

Extron electronics FOX II T HD 4K Manuel utilisateur

Extron electronics

Extron electronics DTP2 T 202 FB Manuel utilisateur

Extron electronics

Extron electronics MTP T 15HD A Manuel utilisateur

Extron electronics

Extron electronics DVI 201xi TX Manuel utilisateur

Extron electronics

Extron electronics FOX3 T 301 Manuel utilisateur

Extron electronics

Extron electronics XTP T HDMI Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur