Extron electronics System 4xi Manuel utilisateur

Extron • System 4

Switcher Series • User’s Manual • P/N 68-408-02 Rev. A

Configuration and ConnectionsSony Installation

SYSTEM 4xi

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: SONY

Included Communications Adapter(s):

Quantity Part Number Description

1 26-312-01 ADP, SONY CCQ ADAPTER

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔”IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: SONY

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM

AS 1 2 3 4 CABLE ADAPTER

✔Sony off on off on 0 0 3 5 0 J15 26-312-01

Extron • System 4

Switcher Series • User’s Manual • P/N 68-408-02 Rev. A

Sony Installation Configuration and Connections

(Note: Information depends on

stem 4 setup.

)

(See note.)

[System 4 model and software

version displayed here]

Connecting System 4xi to Sony

If the System 4xi is already configured for a Sony projector, go to step 4. If it is

not set up correctly, it will be necessary to change switch settings on the

System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct

configuration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xi

is already set up for the Sony projector. Apply power to the System 4xi and do

the following:

a. Press to display the MENU SELECT on the LCD screen.

b. Press or to step to Menu 8.

c. Press to select this menu.

d. Press or to display the configuration. The example to the left is general,

yours will show the System 4xi model name, the software version and the

following information:

PRJ = SONY

PRJ BAUD = 9600

UNIT No. = 000

HST BAUD = 9600 (value depends upon setup Menu 3)

2. Go to the procedure on page 2-3 of the

System 4

User’s Manual

to remove the

System 4xi cover. Then go to page 2-4 and refer to the configuration below to

set up the Main Controller board. Continue with Step 3 (below) when the

configuration is correct.

Config Projector SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Comm

as Adapter

✔Sony off-on-off-on 0 0 3 5 0 J15 26-312-01

3. Double-check your work and be sure the System 4xi cover is on securely.

4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.

__________ Changes in some switch configurations are not detected until the power is

removed at the AC cord, and then restored.

Refer to the following connection diagram and continue.

Page 1

}

SW1

SW2

SW4

SW3 SW5

J15

Extron • System 4

Switcher Series • User’s Manual • P/N 68-408-02 Rev. A

Configuration and ConnectionsSony Installation

5. The Sony Comm Adapter (SY COM) has a 9-pin male connector that

accommodates the Comm Extension cable. It also has eight BNC connectors for

all video signals. Both control and video signals are combined in a cable with a

single, 14-pin connector. This plugs into the projector’s “Remote 1” connector.

6. Plug the 15-pin HD connector of the Projector Communications Extension cable

into the PJ Comm port on the System 4xi.

______ Secure all of the connector screws.

7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV

cable onto the System 4xi output and those on the other end onto the matching

BNCs on the Sony connector panel.

System 4xi Series – Sony Projector Connections

Use the illustration below as a guide when connecting the System 4xi to a Sony

projector. Refer to Sony documentation to continue the installation.

____________ In a rack mount, do NOT allow the weight of the cables to be supported by the

System 4

. See page 2-5 for cabling guidelines.

____________ See the following pages for stacking Sony projectors.

Page 2

Extron • System 4

Switcher Series • User’s Manual • P/N 68-408-02 Rev. A

Sony Installation Configuration and Connections

Page 3

__________ For either of the following procedures, the projector(s) must be set up to use the

BNC input. This means the video signals will

NOT

go through the Comm Adapter.

Use the Sony Manual that came with the projector for the procedure for

removing the circuit board and resetting the switch. A simple illustration is also

included in the figure on the previous page.

Frequencies above 48 kHz (see previous illustration)

For a better quality picture at higher frequencies, don’t use the 14-pin cable for

the RGB signals; use the BNC connectors on the projector instead.

See note at the top of this page and use the diagram on the previous page for

the following steps.

7a. The Sony Adapter (SY COM) has one 9-pin male connector that

accommodates the Comm Extension cable. Do NOT use the eight BNC

connectors on the adapter. Only the control signals will go through the Comm

Adapter. Plug the single 14-pin connector from the adapter into the connector

marked “Remote 1” on the Sony connector panel.

8a. Plug the 15-pin HD connector of the Projector Communications Extension cable

(shown as CC 50') into the PJ Comm port on the System 4xi. The other end has

a 9-pin female connector. Plug this end into the 9-pin male D connector on the

SY COM adapter and secure the screws.

9a. Plug the BNC connectors on one end of the RGBS cable onto the System 4xi

output and those on the other end onto the matching BNCs on the Sony

projector.

Stacking Sony Projectors (see following illustration)

Sony projectors are sometimes “stacked” to provide increased brightness. This

technique uses two projectors which display the same image at the same time

on the same screen. To supply RGBS signals to two projectors, an Analog

Distribution Amplifier is required, as well as three, Hi-Res 5-BNC cables.

If the System 4xi is not already setup for Sony, follow steps 1 through 6 on the

previous pages. To parallel-connect the projectors, choose which projector will

be #1 and which will be #2, and continue.

See note at the top of this page and use the following illustration for the following

steps.

7b. Connect the Communications Extension cable from the System 4xi to the

adapter.

8b. Connect the SY COM adapter as shown on the following page. Do NOT use the

eight BNC connectors for the video signals; only the control signals will go

through the adapter. Plug the round, 14-pin connector into the projector

designated as “Projector #1” and turn the collar to secure it in place.

9b. Connect the color-coded, Hi-Res RGBS cable from the BNC outputs of the

System 4 to the input of the ADA.

10b.Connect the first output of the ADA to the BNC input of Projector #1.

Connect the second output of the ADA to the BNC input of Projector #2.

11b.Connect a “mini-phone” control cable from the “Controls Out” jack on

Projector #1 to the “Controls In” jack on Projector #2.

__________ This setup allows any commands, such as remote control, etc., received by

Projector #1 to be passed to Projector #2.

Extron • System 4

Switcher Series • User’s Manual • P/N 68-408-02 Rev. A

Configuration and ConnectionsSony Installation

Page 4

System 4xi - Cable Diagram for Stacking Sony Projectors

Use the following diagram as a guide when connecting the System 4xi to two

Sony projectors. Refer to Sony documentation for further information.

Connecting the System 4

to Two Stacked Sony Projectors

Comm Adapter

SY COM

26-312-01

Table des matières

Autres manuels Extron electronics Changer

Extron electronics

Extron electronics SGS 408 Manuel utilisateur

Extron electronics

Extron electronics SW 4 AR MX HV Manuel utilisateur

Extron electronics

Extron electronics DTP2 T 212 Manuel utilisateur

Extron electronics

Extron electronics SW HD 4K PLUS Series Manuel utilisateur

Extron electronics

Extron electronics SW RGBHV Series Manuel utilisateur

Extron electronics

Extron electronics System 4LD xi Manuel utilisateur

Extron electronics

Extron electronics MediaLink Controllers MLC 104 Series Manuel utilisateur

Extron electronics

Extron electronics IP LINK IPL T PCS4 Manuel utilisateur

Extron electronics

Extron electronics SW2 VGA DA2 A Manuel utilisateur

Extron electronics

Extron electronics MPS 409 Manuel utilisateur

Extron electronics

Extron electronics Matrix 3200 Series Manuel utilisateur

Extron electronics

Extron electronics IN1508 Manuel utilisateur

Extron electronics

Extron electronics SW HDMI Series Manuel utilisateur

Extron electronics

Extron electronics System 8 Plus Manuel utilisateur

Extron electronics

Extron electronics SW2 VGA DA2 A Manuel utilisateur

Extron electronics

Extron electronics RGB 580xi CCSI AAP Manuel utilisateur

Extron electronics

Extron electronics IN1808 Series Manuel utilisateur

Extron electronics

Extron electronics USB HUB4 AAP Manuel utilisateur

Extron electronics

Extron electronics FOX SW8 MM Manuel utilisateur

Extron electronics

Extron electronics Matrix 3200 Series Manuel utilisateur

Extron electronics

Extron electronics CVEQ1 WM Manuel utilisateur

Extron electronics

Extron electronics in1608 series Manuel utilisateur

Extron electronics

Extron electronics VersaTools MSW 4SV Manuel utilisateur

Extron electronics

Extron electronics YCS SW2 A Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur