Extron electronics SW8 HD 4K PLUS Manuel utilisateur

SW6 and SW8 HD 4K PLUS • Setup Guide

The Extron SW HD 4K PLUS are six and eight input HDMI switchers that support 4K video signals at 60 Hz. They

switch 4K/60 signals between multiple HDMI source devices to a single display. The switchers support computer and

video resolutions up to 4K/60 and 1080p/60, data rates up to 18 Gbps, HDR, 12-bit Deep Color, 3D, Lip Sync, and

HD lossless audio formats. Both models feature EDID Minder®, which maintains continuous EDID communication

with connected devices and ensures that the HDMI sources power up properly and maintain correct video output.

The switchers also provide automatic input cable equalization up to 25 feet (7.6 meters) when used with Extron

HDMI Pro Series cable.

The SW HD 4K PLUS Series offers control via front panel buttons, USB, Extron Product Control Software (PCS),

Ethernet, RS-232, contact closure, and auto-input switching for integration with any control system. Front panel LED

indicators provide immediate conrmation of HDCP authentication and signal presence for each input and output.

This guide provides instructions for an experienced installer to set up and operate these switchers.

For full

installation, conguration, and operation details, see the SW HD 4K PLUS Series User Guide, available at

www.extron.com.

Rear Panel Features and Connections

SW6 HD 4K PLUS

Tx Rx G

GCT GC

CT TGC G

TGCT

RS-232

CONTACT IN/TALLY OUT

INPUTS

1 2 3 4 5 6

100-240V 0.2A MAX

50/60 Hz

OUTPUT

REMOTE

LAN

RESET

SW8 HD 4K PLUS

Tx Rx G

GCT GC

CT TGC G

CT TGC

TGCT GC

T+V

RS-232

CONTACT IN/TALLY OUT

INPUTS

1 2 3 4 5 6 7

100-240V 0.2A MAX

50/60 Hz

OUTPUT

REMOTE

LAN

RESET

AA BB

APower connector ERS-232 connector

BHDMI Input connectors FLAN (Ethernet) connector

CHDMI Output connector GContact closure input and tally output ports

D+V connector (for tally voltage output) HReset button

Figure 1. SW6 and SW8 HD 4K PLUS Rear Panel

Installation Steps

1. Turn off all of the equipment and disconnect it from the power source.

2. Mount the switcher on a rack shelf or furniture (optional). (See the instructions provided with the mounting kit,

which can be ordered at www.extron.com).

3. Connect HDMI input sources to one or more of the SW HD 4K PLUS input connectors (see gure 1, B).

NOTE: LockIt®cable lacing brackets, one for each HDMI input and output connector, are provided with the

SW HD 4K PLUS. These brackets can be used to secure the HDMI cables to the rear panel connectors

to reduce stress on the HDMI connectors and prevent signal loss due to loose cable connections. For

information on attaching the LockIt brackets, see the LockIt HDMI Lacing Bracket instructions in the

SW HD 4K PLUS Series User Guide, available at www.extron.com.

SW6 and SW8 HD 4K PLUS • Setup Guide (Continued)

4. Connect an HDMI output device to the output connector (see ﬁgure 1, C, on the previous page). By default,

the EDID of this device is stored at the HDMI output.

5. Connect control devices. Connect your computer

to one of the following SW HD 4K PLUS

communication ports to congure and control the

switcher via SIS commands or via PCS (Cong and

LAN ports only):

• RS-232 port — Connect the unterminated

transmit, receive, and ground wires of the RS-232

cable to the provided 3-pole captive screw plug, as

shown in the illustration at right. Connect the plug

between the rear panel RS-232 connector (E), and

the serial port of your computer. Protocol for the

RS-232 port is 9600 baud, 8 data bits, 1 stop bit,

no parity.

• Config port — Connect a USB mini-B cable between the front panel USB mini-B connector (see ﬁgure 2,

B, on page 3) and a USB port on your computer for control via USB.

• LAN port — Use an RJ-45 cable to connect this jack (see figure 1, F) to a LAN for Ethernet control of the

switcher.

6. (Optional) Connect contact closure and indicator devices. The REMOTE panel on the SW6 and SW8

models contains six (SW6) or eight (SW8) 3-pole captive screw connectors, each with three pins labeled C, G,

and T, for contact closure and tally indicator devices. The panel also contains a 3-pole captive screw connector

with three +V pins that provide power to the indicator devices connected to the tally (T) ports (see 2in the

illustration below right).

Each 3-pole connector is labeled with the number of the HDMI input associated with it. Wire devices to these

connectors as follows:

a. Connect contact input and tally output devices to one or

more of the 3-pole CONTACT IN/TALLY OUT connectors

(see 1in the illustration at right), as desired:

• To enable input switching via contact closure, connect

a push-button contact closure input device to pins C

(contact) and G(ground).

• To identify the currently selected input when the front

panel buttons are not visible, connect an indicator

device, such as an LED, to tally output pin Tof the

same 3-pole connector.

When the input you are using is selected, the

corresponding tally out pin shorts to ground, which activates the connected indicator.

b. If desired, attach the power wires for your connected indicator devices to any of the three ports of the +V

connector (2).

NOTE: You need to connect the indicator LED to the voltage output if you want to power the device for

visual feedback. However, only the contact and ground connections are needed to select an input.

Pressing the button on the contact closure device switches the connected input to the output.

Computer or

Control Syste

RS-232 Port

SW HD 4K Series Switcher

Rear Panel

Remote Port

NOTE: If you use cable that has a drain

wire, tie the drain wire to ground at both ends.

Ground (G)

Transmit (Tx)

Receive (Rx) Transmit (Tx)

Receive (Rx)

Tx Rx G

RS-232

Tx Rx G

GCT GC

CT TGC G

CT TGC

TGCT GC

T+V

RS-232

CONTACT IN/TALLY OUT

REMOTE

11 2

Using a Show Me®cable:

The Contact and Tally connectors can also be used with Extron Show Me cables. The

diagram at right shows how to wire a Show Me cable to a contact input.

For each Show Me cable:

• Connect the red pigtail to the Cpin corresponding to the input being used.

• Connect the black pigtail to the Tpin of the same input.

NOTE: The ground or drain wire on the Show Me cable is not used here. You can tie

it back and shield it.

7. Connect the rear panel IEC power connector to an AC source (see ﬁgure 1, A, on page 1).

8. Power on the output display.

9. Power on the source devices.

Front Panel Features

SW8 HD 4K PLUS

HDMI SWITCHER

CONFIG

SIGNAL

INPUTS

INPUTS OUTPUT

12345678

HDCP

2 3 4

AUTO

SWITCH

5 6 7 8

CCA

A BB

AAUTO SWITCH LED DHDCP LEDs

BUSB CONFIG port EInput selection buttons

CSIGNAL LEDs

Figure 2. SW6 and SW8 HD 4K

PLUS

Front Panels

NOTE: The SW6 front panel is identical to that of the SW8 except that it has six input buttons, Signal LEDs, and

HDCP LEDs.

A AUTO SWITCH LED — Lights when auto-input switching is in effect. When auto-input switching is enabled, the

switcher automatically switches to the highest-numbered input with an active video signal.

B USB CONFIG port — Connect a USB cable (USB A to mini-B) between your computer and this female USB

mini-B port to configure and control the switcher via SIS commands or PCS, and to update the firmware.

C SIGNAL LEDs — The LEDs labeled INPUTS each light when the corresponding input is connected to a device

that has power. The LED labeled OUTPUT lights when the output is connected to a device that has power.

D HDCP LEDs

• Input LEDs — Light if the connected sources are HDCP encrypted and have been authenticated by the

switcher inputs.

NOTE: If the source device connected to the selected input is HDCP encrypted (requires HDCP

authentication), the corresponding signal LED may not light unless HDCP has been authenticated.

• Output LED — Lights when the currently selected input requires HDCP and the connected output device

has been successfully authenticated.

NOTE: HDCP is re-authenticated on the output whenever a new input is selected.

CONTACT IN/TA LLY OUT

Connector

Black

Red

Show Me

Cable

CTG

SW6 and SW8 HD 4K PLUS

68-2940-51 Rev. A

07 18

EInput selection buttons — Press one of these buttons to select an input to switch to the output. The LED at

the right of each button lights when the corresponding input is selected. If auto-input switching is in effect, these

buttons are disabled, but the LEDs continue to light to indicate the selected input. The input buttons are also

used to initiate a system reset and to enable and disable front panel lockout (see the SW HD 4K PLUS Series

User Guide for more information).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Extron electronics Changer

Extron electronics

Extron electronics IN1606 Manuel utilisateur

Extron electronics

Extron electronics SW USB Pro Series Manuel utilisateur

Extron electronics

Extron electronics MPX 866 A Manuel utilisateur

Extron electronics

Extron electronics MLS 100 A Manuel utilisateur

Extron electronics

Extron electronics ISS 608 Manuel utilisateur

Extron electronics

Extron electronics SW RGBHV Series Manuel utilisateur

Extron electronics

Extron electronics SW2 VGA Ars Manuel utilisateur

Extron electronics

Extron electronics SW HD 4K PLUS Series Manuel utilisateur

Extron electronics

Extron electronics ISS 608 Manuel utilisateur

Extron electronics

Extron electronics FOX 4G Matrix 3200 Manuel utilisateur

Extron electronics

Extron electronics RSB129 Manuel utilisateur

Extron electronics

Extron electronics SW2 VGA Series Manuel utilisateur

Extron electronics

Extron electronics UCS 303 Manuel utilisateur

Extron electronics

Extron electronics Extron SW 2 VGAcc Manuel utilisateur

Extron electronics

Extron electronics System 4LD xi Manuel utilisateur

Extron electronics

Extron electronics SW4 ARxi Manuel utilisateur

Extron electronics

Extron electronics Matrix 3200 Series Manuel utilisateur

Extron electronics

Extron electronics SW DVI Plus Series Manuel utilisateur

Extron electronics

Extron electronics XTP T USW 103 Manuel utilisateur

Extron electronics

Extron electronics SW8/12 VGA Ars Manuel utilisateur

Extron electronics

Extron electronics XTP T USW 103 Manuel utilisateur

Extron electronics

Extron electronics YCS SW2 A Manuel utilisateur

Extron electronics

Extron electronics IN1604 DT Manuel utilisateur

Extron electronics

Extron electronics XTP T USW 103 4K Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur