Extron electronics MPS 601 Manuel utilisateur
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
MPS 601 • Setup Guide
This guide provides basic instructions for an experienced technician to install, set up, and operate the Extron Media Presentation
Switcher, MPS 601. Installation and service must be performed by authorized personnel only. For additional information and
specications, see the MPS 601 product page at www.extron.com.
Step 1 — Mount the MPS 601
The MPS 601 is housed in a half rack width, 6 inch deep, 1U high metal enclosure that can sit on a table with the provided rubber
feet or can be rack mounted. Select a suitable mounting location, then choose an appropriate mounting option.
Step 2 — Cable the Switcher
0.5 A MAX
POWER
12V
1
2
B
A3
4
5
6
INPUTS
MPS 601
CONTACT IN / TALLY OUT
HDMI
RGBHV
HDMI
HDMI RS-232
GC
135
246
TTCG TCG
GCT TCG T+V
CG
Tx Rx G
OUTPUT
REMOTE
$$%%&&''(()
)*
*
+
+
Figure 1. MPS 601 Rear Panel
Power and Input Connections Output Connection Control Device Connections
ADC power connector
BTwo configurable analog
15-pin HD (VGA) connectors
CTwo female 3.5 mm TRS
connectors — (lettered A and B
on the rear panel) corresponding
to the two RGBHV video inputs
DFour female HDMI connectors
— for HDMI compliant audio
and video input (numbered 3, 4,
5, and 6 on the rear panel).
EOne female HDMI connector FContact In/Tally Out — Six
3.5mm, 3-pole captive screw
connectors for automatic input
switching and tally indication
using Extron Show Me cables.
G+V Port — 3-pole 3.5mm
captive screw connector for +V
output.
HRS-232 — 3-pole, 3.5mm
captive screw connector.
Connect Inputs
1. RGBHV video inputs — Connect analog video sources to the HD connectors (see gure 1, B). The connectors accept VGA
signals.
NOTE: The MPS 601 digitizes the RGBHV inputs. It does not scale or convert video to a different resolution. The output
signal resolution is the same as the input resolution.
2. Analog audio inputs — By default, audio input A is tied to RGBHV input 1 and audio input B is tied to RGBHV input 2 (C).
Analog audio is digitized for HDMI output.
3. HDMI video inputs — Connect digital HDMI sources to these inputs using standard HDMI cables (D).
Connect Output
HDMI video output — Connect an HDMI display device using a standard HDMI cable (E).
figure 1
2
MPS 601 • Setup Guide (Continued)
Connect Control Devices
NOTE: Do not tin the leads. Tinned wires are not as secure in the connector and could be pulled out.
• Contact In/Tally Out —When a connected contact is grounded, the corresponding input is selected (see figure 1, Fon the
previous page). At the same time, the tally output closes causing the Show Me cable LED indicator to light.
NOTE:
• For “Show Me” cables, the ground pin is optional.
• Do not connect “Show Me” cables to the +V pin of the +V Port (see below).
The six contacts are mutually exclusive so that only one input can be selected at a time.
• Contact (C) – Momentary closure of this pin to ground selects the corresponding
Ground (G)
Ta lly (NO)
Contact (NO)
TC G
Do not tin
the wires!
number input. Selection is triggered at the closure (grounding) of the pin, not the
opening.
• Ground (G) – Ground pin.
• Tally output (C) – Controls the LEDs on the contact closure push button. When an input
is selected, the tally LED for that input is active.
• +V Port — All three pins constantly output +5 VDC, 200 mA total (shared between pins).
+V
+V
+V
Do not tin
the wires!
The +V pins can provide power to illuminate external tally LEDs (G).
• Remote RS-232 — Serial port for connection of a host computer or controller using
Simple Instruction Set (SIS™) or Windows-based control software commands (H).
Ground ( _)
Receive (Rx)
Transmit (Tx)
Bidirectional
RS-232
Device
Ground ( _)
Receive (Rx)
Transmit (Tx)
RxTx
Do not tin
the wires!
The default protocol is 9600 baud, 8 data bits, 1 stop bit, and no parity.
An IP Link® driver allows Extron IPL and MediaLink® devices to control the MPS 601
from the RS-232 remote connector.
Connect Power
Connect the provided 12 VDC power supply to the rear panel captive
Ground
+12 VDC input
G
External Power Suppl
y
(12 VDC, 0.5 A max.)
Ground all
Devices
DC Power Cord
Captive Screw
Connector
3/16"
(5 mm) Max.
screw connector (A) and plug the AC power cord into 100-240 VAC,
at 50-60 Hz.
ATTENTION:
• Always use a power supply provided by or specied by Extron. Use of an unauthorized power supply voids all
regulatory compliance certication and may cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source
d’alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi
que le produit nal.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The
power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location,
Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium, or desk.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération
ou dans les cavités murales. La source d’alimentation doit être située à proximité de l’équipement de traitement
audiovisuel dans un endroit ordinaire, avec un degré2 de pollution, xé à un équipement de rack à l’intérieur d’un
placard, d’une estrade, ou d’un bureau.
3
ATTENTION:
•The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA
70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently xed to
building structure or similar structure.
•Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/
NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être
xée de façon permanente à une structure de bâtiment ou à une structure similaire.
•This product is intended for use with a UL Listed power source marked Class 2 or LPS and rated 12VDC, minimum
0.5 A.
•Ce produit est destiné à une utilisation avec une source d’alimentation certifiée UL de classe 2 ou LPS et calibrée à 12
Vcc, 0,5 A minimum.
Configuring the MPS 601
The MPS 601 can be congured using a connected PC and the Extron Product Conguration Software or using SIS commands.
To congure the MPS 601 using the Product Conguration Software, install the software (available on the Extron website, www.
extron.com) on a PC connected to the MPS 601 by the rear panel remote (RS-232) port (see gure 1, h), or front panel USB
Cong port (see gure 6, b). After the installation, start the program. See the MPS 601 User Guide and the Product Conguration
Software Help File for additional information.
To congure the MPS 601 using SIS commands, see the MPS 601 User Guide.
MPS 601
MEDIA PRESENTATION SWITCHER
CONFIG
SIGNAL
INPUTS
INPUTS OUTPUT
12 345 6
HDCP
1 2 3 4 5 6
AUTO
SWITCH
$$%%&
&'
'(()
)*
*
Figure 2. MPS 601 Front Panel
Setup and Operation
APower on all connected devices, then apply power to the MPS 601. The Auto Switch LED lights when auto-input switching is
active.
BOne mini type-B female USB Config port connects to a host computer for configuring the switcher and upgrading firmware.
CInput switching. The input group has six buttons with associated green LEDs. Press an input button to switch the input to the
HDMI output. The associated LED lights. Only one of the six inputs can be selected at a time.
DInput signal LEDs. Six green LEDs indicate:
•The LEDs for RGBHV inputs 1 and 2 light when horizontal sync is detected on the input.
•The LEDs for HDMI inputs 3 to 6 light when TMDS clock activity is detected on the input.
NOTE: If a connected HDMI source is HDCP encrypted, the associated input signal LED does not light until HDCP is
authenticated.
EOutput signal LED. This LED lights when the HDMI output is connected to a display or sink device.
FHDCP input signal LEDs (inputs 3, 4, 5, and 6). These LEDs light for the associated HDMI input when the connected source is
HDCP encrypted.
GHDCP output LED. This LED lights when the currently selected input source requires HDCP and the connected output device
(sink) is authenticated.
The MPS 601 can be connected to as many as six input devices. Any of the six inputs (2 RGBHV, 4 HDMI) can be routed to the
HDMI output.
4
68-2454-50 Rev. B
10 18
© 2014-2018 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
Executive Mode
Executive mode, when enabled, provides security from an accidental or unauthorized front panel button press by locking out the
input switching buttons.
The RS-232 and USB ports are always accessible regardless of the executive mode state.
To enable or disable executive mode:
• Press and hold input 1 and input 2 for 3 seconds to toggle executive mode on or off.
• The front panel LEDs ash twice to indicate that executive mode is enabled or disabled.
All LEDs ash twice if a button is pressed while executive mode is enabled.
Figure 3. MPS 601 Application Diagram
Autres manuels pour MPS 601
2
Table des matières
Autres manuels Extron electronics Changer
Extron electronics
Extron electronics DTP2 R 212 Series Manuel utilisateur
Extron electronics
Extron electronics SW DVI A Series Manuel utilisateur
Extron electronics
Extron electronics SW AV Manuel utilisateur
Extron electronics
Extron electronics SW8 HD 4K PLUS Manuel utilisateur
Extron electronics
Extron electronics SW4 3G HD-SDI Manuel utilisateur
Extron electronics
Extron electronics MLS 608 D SA Manuel utilisateur
Extron electronics
Extron electronics WPD 181 Manuel utilisateur
Extron electronics
Extron electronics Converter CVC 200 Manuel utilisateur
Extron electronics
Extron electronics ISS 608 Manuel utilisateur
Extron electronics
Extron electronics MSW 4V SDI rs Manuel utilisateur
Extron electronics
Extron electronics IN1604 DT Manuel utilisateur
Extron electronics
Extron electronics DTP T SW4 HD 4K Manuel utilisateur
Extron electronics
Extron electronics SW4 12G HD-SDI Manuel utilisateur
Extron electronics
Extron electronics MGP 641 xi Series Manuel utilisateur
Extron electronics
Extron electronics SW RGBHV Series Manuel utilisateur
Extron electronics
Extron electronics SW6 YUV A Manuel utilisateur
Extron electronics
Extron electronics PVT Series Manuel utilisateur
Extron electronics
Extron electronics Extron MediaLink MLS 304MA Manuel utilisateur
Extron electronics
Extron electronics Extron SW 2 VGAcc Manuel utilisateur
Extron electronics
Extron electronics SW2 DVI A Plus Manuel utilisateur
Extron electronics
Extron electronics PVS 405D Manuel utilisateur
Extron electronics
Extron electronics SW DVI Plus Series Manuel utilisateur
Extron electronics
Extron electronics IP LINK IPL T PCS4 Manuel utilisateur
Extron electronics
Extron electronics PVS 204SA Plus Instructions d'installation et d'utilisation
