Extech Instruments MA120 Manuel utilisateur

User’s Guide

Model MA120

200A AC/DC Mini Clamp-on Meter

MA120 Ver. 1.2 10/2004

Introduction

Congratulations on your purchase of Extech’s MA120 AC/DC Mini Clamp Meter. This professional

meter, with proper care, will provide years of safe reliable service.

Meter Description

1. Current sense jaw

2. Non-contact AC voltage indicator light

3. Flashlight button

4. Rotary function switch

5. Data HOLD and Backlight key

6. LCD display

7. Clamp trigger

8. One-touch DCA ZERO key

Safety Information

!Caution! Refer to the explanation in this Manual

Double Insulation

This meter has been designed to be safe in use, but the operator must use caution in its operation.

The rules listed below should be carefully followed for safe operation.

1. NEVER apply voltage or current to the meter that exceeds the specified maximum:

2. USE EXTREME CAUTION when working with voltages greater than 60VDC or 25VAC rms.

These voltages are considerd a shock hazard.

3. NEVER operate the meter unless the back cover and the battery/fuse door are in place and

fastened securely.

Input Limits

Function Maximum Input

AC Current 200A

DC Current ±200A

Frequency 1kHz

23456

MA120-V1.3-EN-3/12

Operation

AC Current Measurements

1) Set the Function switch to the ACA range.

2) Press the jaw trigger and clamp around, fully enclosing a single conductor.

Do not allow a gap between the two halves of the jaw. Refer to the diagram

at right for the correct way to enclose a single conductor.

3) Read the ACA value on the LCD.

DC Current Measurements

1) Set the Function switch to the DCA range.

2) Press the ZERO key to null the meter display.

3) Press the Trigger to open the current sense Jaw.

4) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the

jaw.

5) Read the DCA value on the LCD.

Non-Contact AC Voltage Detection

1) AC Voltage detection operates on any of the four Function switch positions.

2) Touch the probe tip to the hot conductor or insert into the hot side of the electrical outlet.

3) If AC voltage is present, the detector light will illuminate.

NOTE: The conductors in electrical cord sets are often twisted. For best results, slowly slide the

probe tip along a length of the cord to assure placing the tip in close proximity to the live

conductor.

NOTE: The detector is designed with high sensitivity. Static electricity or other sources of energy

may randomly turn the detector light on. This is normal operation

Frequency Measurements

1) Set the Function switch to the Hz position.

2) Fully enclose the conductor to be measured. Do not allow a gap between the two halves of the

jaw.

3) Read the Frequency value on the LCD.

Flashlight

Press and hold the top button to turn the flashlight on. Release the button to turn the flashlight off.

Data Hold

To freeze the current reading on the LCD, press the “Hold / Backlight” key. The word HOLD will

appear on the LCD while the meter is in the Data Hold mode. To release the Data Hold function and

return the meter to normal operation, press the “Hold / Backlight” key again. The word HOLD will

switch off.

Backlight Display

Press and hold the “Hold / Backlight” key for more than 2 seconds to turn on the backlight. This will

also activate the Data Hold function. To release the Data Hold function and return the meter to normal

operation, press the Data Hold key momentarily. To turn off the backlight, press and hold the “Hold

Backlight” key for more than 2 seconds.

Yes

WARNING: Risk of Electrocution. Before use, always test the Voltage Detector on a

known live circuit to verify proper operation

MA120-V1.3-EN-3/12

Specifications

General Specifications

Display 3-2/3 (2400 count) Digit LCD with white LED backlight

Polarity Minus sign ( - ) indicates negative polarity

Current sensor Hall effect sensor type

Overload indication “OL” displayed on the LCD

DCA zero adjust One touch zero key

Display rate 2 readings/second, nominal

Battery Two 1.5V AAA batteries

Low Battery indication “BATT” displayed on the LCD

Operating conditions 32ºF to 86ºF (0ºC to 30ºC) 90%RH; 86ºF to 104ºF (30ºC to 40ºC) 75%RH;

104ºF to 122ºF (40ºC to 50ºC) 45%RH

Storage conditions - 14ºF to 140ºF (-30ºC to 60ºC); < 90% Relative Humidity

Altitude Operate at less than 3000 meters

Weight 6.2 oz. (176g) including battery

Dimensions 6.5 x 2.6 x 1.3” (164 x 65 x 32mm) (HWD)

Jaw opening 0.7” (18mm)

Standards IEC 1010 Category III 300V, Category II 600V,

Range Specifications

Function Range Resolution Accuracy (of reading)

DC Current 200A 0.1A ± (2.8% + 8 digits)

AC Current 200A 0.1A ±(3.0% + 8 digits)

40-51Hz 0.01Hz

51-510Hz 0.1Hz

Frequency

(Auto-Ranging)

0.51-1kHz 0.001kHz

±(1.2% + 5 digits)

Input Sensitivity: 2.5A AC RMS min.

Non-Contact AC Voltage 100VAC to 600VAC 50/60Hz

MA120-V1.3-EN-3/12

Support lines: U.S. 877-439-8324, Intl. 603-324-7800

Technical support: Option 3; E-mail: [email protected]

Repair & Returns: Option 4; E-mail: [email protected]

Product specifications subject to change without notice

Visit our website: www.extech.com

Extech Instruments Corporation, 9 Townsend West, Nashua, NH 03063

ISO 9001 Certified since 1995

Maintenance

Battery Replacement

1) When the low battery symbol appears on the LCD the batteries must be replaced.

2) Power down and remove the rear battery compartment Phillips screw.

3) Lift off the battery compartment cover and replace the two 1.5V AAA cells.

4) Replace compartment cover and secure the screw.

You, as the end user, are legally bound (EU Battery ordinance) to return all used

batteries, disposal in the household garbage is prohibited! You can hand over your

used batteries / accumulators at collection points in your community or wherever batteries /

accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle

Cleaning

Caution: Use only a dry cloth to clean the plastic case.

Warranty

EXTECH INSTRUMENTS CORPORATION (a FLIR company) warrants this instrument to be free of defects in parts and workmanship for

one year from date of shipment (a six month limited warranty applies to sensors and cables). If it should become necessary to return the

instrument for service during or beyond the warranty period, contact the Customer Service Department for authorization. Visit our website

www.extech.com for contact information. A Return Authorization (RA) number must be issued before any product is returned to Extech. The

sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not

apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance

or repair, or unauthorized modification. Extech specifically disclaims any implied warranties or merchantability or fitness for a specific

purpose and will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or

replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or

implied.

Calibration and Repair Services

Extech offers repair and calibration services for the products we sell. Extech also provides NIST certification for most products. Call the

Customer Service Department for information on calibration services available for this product. Extech recommends that annual calibrations

be performed to verify meter performance and accuracy.

Table des matières

Autres manuels Extech Instruments Instrument de mesure

Extech Instruments

Extech Instruments DT300 Manuel utilisateur

Extech Instruments

Extech Instruments 451104 Manuel utilisateur

Extech Instruments

Extech Instruments MA160 Manuel utilisateur

Extech Instruments

Extech Instruments HDV7C-A2-39-HD-1 Manuel utilisateur

Extech Instruments

Extech Instruments 407768 Manuel utilisateur

Extech Instruments

Extech Instruments 407114 Manuel utilisateur

Extech Instruments

Extech Instruments 445580 Manuel utilisateur

Extech Instruments

Extech Instruments PQ3450-2-NIST Manuel utilisateur

Extech Instruments

Extech Instruments 380193 Manuel utilisateur

Extech Instruments

Extech Instruments RH25 Manuel utilisateur

Extech Instruments

Extech Instruments EC150 Manuel utilisateur

Extech Instruments

Extech Instruments 407412 Manuel utilisateur

Extech Instruments

Extech Instruments C015 Manuel utilisateur

Extech Instruments

Extech Instruments HD600 Manuel utilisateur

Extech Instruments

Extech Instruments Oyster-10 Manuel utilisateur

Extech Instruments

Extech Instruments 38389 Manuel utilisateur

Extech Instruments

Extech Instruments SDL600 Manuel utilisateur

Extech Instruments

Extech Instruments MA140 Manuel utilisateur

Extech Instruments

Extech Instruments Oyster 341350A-P Manuel utilisateur

Extech Instruments

Extech Instruments 380580 Manuel utilisateur

Extech Instruments

Extech Instruments CO10 Manuel utilisateur

Extech Instruments

Extech Instruments MA150-T Manuel utilisateur

Extech Instruments

Extech Instruments MA250 Manuel utilisateur

Extech Instruments

Extech Instruments 407510 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur