Extech Instruments DL150 Manuel utilisateur

User's Guide

True RMS AC Voltage/Current

Datalogger

Model DL150

DL150-EU-EN V2.5 5/13

Introduction

Congratulations on your purchase of this Voltage or Current datalogger. With this meter, you can

monitor and log data over long periods of time and then easily transfer the data to a pc for viewing

and evaluation. The LCD display provides real time data, Max/Min data and time information. This

meter is shipped fully tested and calibrated and, with proper use, will provide years of reliable

service.

Safety

Warning!

Do not attempt to make measurement in flammable gaseous areas!

When testing a non-insulated cable, pay attention to avoid short circuits.

Do not attempt to use the instrument when your hand is wet!

Do not input over range during measurements.

Never open the battery cover during measurements.

Stop using the instrument when there is any structural defect or exposed metal parts.

Do not install substitute parts or make modifications on the meter.

Never replace the battery in moist areas.

Ensure the meter is disconnected and switch off before opening the battery cover to replace

the battery.

Do not attempt to place the instrument in high vibration areas.

Do not expose the meter to direct sunlight, high temperature and high moisture environment.

Switch off the meter after use. Remove the AAA batteries when the meter will be stored for a

period of time..

When cleaning, do not use abrasives or solvents on the meter, use a damp cloth and mild

detergent only.

DL150-EU-EN V2.5 5/13

Description and Button Functions

1. LCD Description

: Normal record mode is selected

:Capture record mode is selected. Records the sine

wave when the measure value exceeds the Capture

Detection set level.

: Auto power off setting, the meter will automatically

shuts off after 5mins without any button presses.

: Average peak measure and record mode selected

(about 195ms)

: Recording status. After the record mode is set up by the software, press the

START/STOP button for more than 4 seconds to begin recording. This icon will be

displayed and indicates the meter is recording data. Press the same button again for

more than 4 seconds to stop recording.

: Record until full is selected. When the memory is full, the datalogger will stop recording.

: Continuous recording is selected. When the memory is full, the data will overwrite the

oldest data.

: Memory full and recording has stopped.

: Battery sign, when display completely the battery power is full. When there is only a

frame icon displayed, the battery is exhausted and should be replaced with a new one.

DL150-EU-EN V2.5 5/13

2. AC adaptor Jack

3. ON/OFF Button

4. MAX/MIN : Press the button one time to display the MAX

(maximum) reading . Press again to display the MIN (minimum)

reading. A third press will exit MAX/MIN mode. The meter will

automatically exit MAX/MIN mode in 10 seconds if no button is

pressed.

5. CH Input Jack: Insert the current or voltage sensor to this COM to

measure and record the data.

6. PEAK HOLD: In the non-PEAK measurement mode, press the

PEAK HOLD button to display the average Peak value of the

present value. Press the button again to exit PEAK display. The meter will automatically exit in

10s if no button is pressed.

7. START/STOP: Press the START/STOP button for one time to pause data. Press again to

resume. After setting the record mode, press this button for more than 4 seconds and then

release it after REC is shown on the LCD. The meter will measure and record data according to

the software setup.

8. USB Port

9. AC Current Clamp Jaw: Clamp the jaws around a single

conductor for AC current measurements to 200A

10. Jaw Opening Trigger:

11. CH Plug:

12. AC Voltage Probes or Alligator clips

13. Voltage module

14. CH Plug

910 11

DL150-EU-EN V2.5 5/13

Operation

1. Install 4 fresh AAA batteries or connect the AC adaptor.

2. Set-up the datalogger using the software provided.

3. Connect the voltage test leads or the current probe to the meter and hen to the AC source to

be measured.

4. Press and Hold the START/STOP button for four seconds to start recording. The “REC” icon

will appear in the display indication that recording has begun.

5. Press and Hold the START/STOP button for four seconds to stop recording. The “REC” icon

will disappear from the display.

6. Remove the probe, connect the datalogger to a PC and use the supplied software to download

the data.

7. After each recording you will need to connect to the PC and supplied software to download the

data and set up for the next recording.

You, as the end user, are legally bound (Battery ordinance) to return all used batteries and

accumulators; disposal in the household garbage is prohibited!

You can hand over your used batteries / accumulators at collection points in your community

or wherever batteries / accumulators are sold!

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the

end of its lifecycle.

Note: If the clock does not set to the correct time, replace the 3V button battery.

Software Introduction

1. Place the CD in the drive and then follow the on-screen installation instruction.

2. After the software is installed, keep the CD in the drive and connect the datalogger to the PC

by the USB cable.

3. A USB Driver installation window will pop-up. Follow the directions to install the driver.

System Required:

Windows 2000, Windows XP, Vista, Windows 7, or Windows 8

Minimum Hardware Required:

PC or NoteBook with Pentium 90MHz or higher 32 MB RAM

At least 7 MB hard disk space available to install Datalogger USB software

Recommended display resolution 1024 x 768 with High Color (16 bit)

Software Operation

The Software operation is described in the HELP file located on the software disk.

DL150-EU-EN V2.5 5/13

Specifications

Display Multi-function LCD

Maximum data points 100,000

Channels Single channel, TRMS AC Voltage or Current

Sample rate 1s to 24h selectable

Transient capture >0.244mS

Analysis software Windows 2000/XP/ Vista/7/8

Data output USB port

Open input indication "LO" appears on the LCD

Low battery indication Empty battery symbol appears on the LCD

Power supply 4 AAA Batteries and 1 CR 3V memory button battery (CR2032 or

equivalent)

Battery life 5 days (approximately)

AC Adaptor 9V, 0.5A

Standards

CAT III 600V

Operating Temperature 0 to 50°C (32 to 122°F)

Operating Humidity <70% RH

Current Clamp Jaw opening 12.7mm (0.5”)

Dimensions 114 x 63 x 34mm (4.5 x 2.5 x 1.3”)

Weight 248g (8.7oz.)

Range Accuracy

Voltage

40Hz to 1kHz

10VAC to 600.0VAC ±2.0%±1V

Current

50/60Hz

10A to 200.0A ±2.0%±1A

Peak Measurement 8.0 to 850.0V ±5.0%

Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform

ISO‐9001Certified

www.extech.com

Table des matières

Autres manuels Extech Instruments Enregistreur de données

Extech Instruments

Extech Instruments SD800 Manuel utilisateur

Extech Instruments

Extech Instruments RHT10 Manuel utilisateur

Extech Instruments

Extech Instruments 382100 Manuel utilisateur

Extech Instruments

Extech Instruments 381395 Manuel utilisateur

Extech Instruments

Extech Instruments 42582 Manuel utilisateur

Extech Instruments

Extech Instruments TH10 Manuel utilisateur

Extech Instruments

Extech Instruments RHT30 Manuel utilisateur

Extech Instruments

Extech Instruments 407760 Manuel utilisateur

Extech Instruments

Extech Instruments DL160 Manuel utilisateur

Extech Instruments

Extech Instruments SD700 Manuel utilisateur

Extech Instruments

Extech Instruments 42280 Manuel utilisateur

Extech Instruments

Extech Instruments 42280-NIST Manuel utilisateur

Extech Instruments

Extech Instruments 380340 Manuel utilisateur

Extech Instruments

Extech Instruments 380340 Manuel utilisateur

Extech Instruments

Extech Instruments TM500 Manuel utilisateur

Extech Instruments

Extech Instruments 42280A Manuel utilisateur

Extech Instruments

Extech Instruments TH10 Manuel utilisateur

Extech Instruments

Extech Instruments DL150 Manuel utilisateur

Extech Instruments

Extech Instruments CO220 Manuel utilisateur

Extech Instruments

Extech Instruments SD800 Manuel utilisateur

Extech Instruments

Extech Instruments VB300 Manuel utilisateur

Extech Instruments

Extech Instruments CO210 Manuel utilisateur

Extech Instruments

Extech Instruments RTH10 Manuel utilisateur

Extech Instruments

Extech Instruments 407780 Manuel utilisateur

Manuels Enregistreur de données populaires d'autres marques

TESTO

TESTO 176 Manuel utilisateur

HT Italia

HT Italia XL421 Manuel utilisateur

HBM

HBM SOMAT XR CX22B-R Manuel utilisateur

Agtrix

Agtrix 380i Manuel utilisateur

Hobo

Hobo H8 Pro Manuel utilisateur

Beijing ART Tech

Beijing ART Tech PCI2320 Manuel utilisateur

Athena

Athena GET SL1 Manuel utilisateur

Motec Systems

Motec Systems C185 Manuel utilisateur

Beijing ART Tech

Beijing ART Tech USB2832 Manuel utilisateur

Rotronic

Rotronic HygroLog HL20 Manuel utilisateur

MRC

MRC DW-6092 Manuel utilisateur

Racelogic

Racelogic VBOX LapTimer Manuel utilisateur

Edu-Logger

Edu-Logger 900-240 Manuel utilisateur

Elma

Elma DT173 Manuel utilisateur

MadgeTech

MadgeTech PRTemp140 Fiche technique

Comet

Comet U0121M Manuel utilisateur

pico Technology

pico Technology PT-104 Manuel utilisateur

Soil Instruments

Soil Instruments GTecLink Manuel utilisateur