Evikon PluraSens E2227 Manuel utilisateur
PluraSens®
Humidity & Temperature Transmitter
E2227
User Manual
E2227 Rev 17.05.2021
Table of contents
Specifications 3
Product description 4
Safety requirements 4
Operating conditions 4
Installation and connection 5
Delivery set 8
Emergency mode 8
Return to default settings 8
Modbus RTU Communication 9
Communication parameters 10
Modbus holding registers 10
Warranty 14
Manufacturer contacts 14
2
E2227 Rev 17.05.2021
Specifications
Sensor type
Digital combined RH and T sensor
Measurement range
0...95 % RH
-20...+70 °C
Resolution
0,01 %RH
0,01 °C
Accuracy
±2,5 % RH / ±0,5 °C
±1,8 % RH / ±0,3 °C on request
Self-diagnostics
Full functionality check at start-up
Warm-up time
≤ 1 s
Response time
<15 seconds
Power supply
11...30 VDC, nominal 24 VDC
Power consumption
< 1,5 VA
Analog outputs
2 × 4-20 mA / 0-10 V, user settable, freely
configurable scales
Load resistance
RL < (Us - 2 V) / 22 mA for 4-20 mA
RL > 250 kOhm for 0-10 V mode
RS485 fieldbus interface
Up to 256 units on bus (1/8 unit load)
no galvanic isolation
Modbus RTU protocol support
Cable connections
Screwless spring loaded terminals
Enclosure
White ABS, wall mount, ventilation slots, protection class IP20
Dimensions
H71 × W71 × D27 mm
Weight
<100 g
Operating environment
Residential, business and industrial, indoor spaces
Operating conditions
20...+70 °C, 0...95% RH non-condensing,
no aggressive gases
CE marking
According to 2014/30/EU:
EN 61000-6-3:2020, EN 61326-1:2013(EMC, emissions)
EN 61000-6-1:2019, EN 61000-6-2:2019(EMC, Immunity)
3
E2227 Rev 17.05.2021
Product description
Humidity and temperature transmitter E2227 is a member of the new PluraSens® family of
multifunctional measurement instruments. The device is intended for the measurement of
relative humidity and temperature in air and non-aggressive gases indoors with high
accuracy and stability. The absolute humidity and dew point values can also be obtained.
Target applications are HVAC and building automation management systems.
The device is equipped with a digital combined RH and T sensor. The sensor is
temperature compensated to avoid transmitter self-heating effects. Compact wall-mount
slotted plastic enclosure provides natural ventilation of the sensor.
Two freely configurable 4-20 mA / 0-10 V analog outputs can be used to connect the
transmitter to secondary instruments. Each output can be independently assigned either to
temperature, relative humidity or dew point channel. RS485 interface with
industry-standard Modbus RTU protocol support allows direct Fieldbus networking of the
transmitter as a Slave unit.
Safety requirements
Always adhere to the safety provisions applicable in the country of use.
Do not perform any maintenance operation with the power on. Do not let water or foreign
objects inside the device.
Operating conditions
The device should be used in explosion-safe (non ATEX-rated) indoor areas without
aggressive gases, dust or mists in the atmosphere.
Allowable conditions are:
– Temperature in the range of -20...+70 °C;
– Relative humidity in the range of 0...95%, without condensation;
– Atmospheric pressure in the range of 0,9...1,1 atm.
4
E2227 Rev 17.05.2021
Installation and connection
To ensure representative measurement of temperature and humidity in the room, choose
carefully the transmitter installation place. E2227 should not be located in direct sunlight,
near heat sources or air conditioning units, near doors and windows, in places where air
circulation is limited, or on poorly insulated and cold external walls.
Detach the base from the enclosure by pulling gently along the four guiding pins. You may
need to drill or cut suitable holes in the base for screws and cable. Attach the base to the
wall either with double-sided adhesive tape or with two screws (see drawings below).
5
E2227 Rev 17.05.2021
PCB without PSU and relays
Jumpers
J1
OUT1 type (open: 4-20 mA; closed 0-10 V)
J2
OUT2 type (open: 4-20 mA; closed 0-10 V)
X6
Reset Modbus network parameters to default
X4 terminals
OUT1
4-20 mA / 0-10 V output
OUT2
4-20 mA / 0-10 V output
0V
0 V / 24 VAC Neutral (optional)
A
RS485 A / Data +
B
RS485 B / Data -
+U
+24 VDC / 24 VAC Phase (optional)
6
E2227 Rev 17.05.2021
Position the transmitter with the ventilation slots upwards and downwards to ensure
proper air convection for faster response and higher accuracy.
Plug the power cable and connect the analog outputs and/or digital interface terminals to
the relevant devices as described below.
E2227 uses screwless quick connect spring terminals suitable for a wide range of wires
with cross-section 0,2...1,5 mm2. We recommend to strip the wire end by 8...9 mm and tin
it, or to use the wire end sleeves. To connect the wire, insert the wire end into the terminal
hole. To disconnect, push the spring loaded terminal lever, pull the wire out, and release the
lever.
Use twisted pair cable, e.g. LiYY TP 2×2×0,5 mm2 or CAT 5, to connect the device to the
RS485 network. Use one pair for A and B wires and the second pair for common 0V and
power +U wires. to connect the transmitter to the Fieldbus network. polarity must be
respected when connecting to an external RS485 network. Overall length of all connections
via RS485 interface should not exceed 1200 m.
Note! The outputs are not galvanically isolated from external power supply and share
common 0V. Allowed load resistance limits are stated in the Specifications table. To power
the instrument from an external power source, connect terminals 0V and +U to the source
(see connection diagram).
Both analog outputs can be independently changed between 4-20 mA and 0-10 V type
using jumpers J1 (OUT1) and J2 (OUT2). By closing pins on a specific jumper the related
output is 0-10 V, with an open jumper the output is 4-20 mA. Power restart is required after
changing the position of the jumpers.
By default the output OUT1 is assigned to relative humidity with default scale 0-100 %RH.
By default the output OUT2 is assigned to temperature with default scale 0-100 °C.
After wiring and setting output options attach the enclosure back to the base.
A LED placed on the PCB of the device to control the connection process. The LED
response to different processes is presented in the table below:
Mode
LED mode
During calibration mode or sensor heating
period (if activated)
0.5 Hz (50% on, 50% off)
During Modbus communication cycle
Short on-off pulses
Normal operating/measurement
Continuously on or off
7
E2227 Rev 17.05.2021
Delivery set
●Humidity and temperature transmitter E2227
●Set of mounting accessories (2 screws with plastic dowels)
Emergency mode
The current outputs of the transmitter may be programmed via Modbus commands to
signal if the connection with the sensor is lost. The signal may be set to 3,8 mA or 21,5 mA.
See the table of Modbus registers for more information.
Return to default settings
To reset the device’s Slave ID, baud rate and stop bit number to factory settings, proceed as
follows:
1. De-energize the device
2. Connect the X6 jumper
3. Turn on the device
4. De-energize the device
5. Disconnect the X6 jumper
6. Turn on the device
8
E2227 Rev 17.05.2021
Modbus RTU Communication
Modbus main holding registers (00xxx or 40xxx): 0-based, decimal
Reg
RW
Description
1
R
hardware version
2
R
software version
3
R
product serial number
4
RW
Slave ID [1...247], default 1
5
RW
baud rate, default 9600
6
RW
response delay [1...255] ms, default 10
7
RW
stop bits , parity bit [1,2,3,4], default 1
17
RW
write ‘42330’ to restart
168
RW
integrating time constant [0...32000] s
201
RW
OUT1 parameter, 0:none, 1:T, 2:RH
202
RW
OUT2 parameter, 0:none, 1:T, 2:RH
258
R
temperature, °C×100, signed integer
259
R
humidity, %RH×100, integer
261
RW
OUT1 out 0%, [±1000] °C / %RH
262
RW
OUT1 out 100%, [±1000] °C / %RH
263
RW
OUT2 out 0%, [±1000] °C / %RH
264
RW
OUT2 out 100%, [±1000] °C / %RH
Note! New Slave ID, baud rate and stop bits values apply after restart
Supported Modbus functions: 03 - read multiple registers, 06 - write single register
9
E2227 Rev 17.05.2021
Communication parameters
Parameter
Permitted values
Default
Supported baud rates
1200, 2400, 4800, 9600, 19200, 38400, 57600
9600
Data bits
8
8
Parity
none / odd / even
none
Stop bits
1, 2
1
Protocol
Modbus RTU
Modbus functions
03 - Read multiple registers
06 - Write a single register
Error codes
01 – Illegal function
02 – Illegal data address
03 – Illegal data value
04 – Slave device failure
(details of last error 04 can be read from register 0x0008)
Modbus holding registers
Registers Reg are shown in hexadecimal 0-based format.
Modbus holding register numbers MHR are shown in decimal 1-based format, and may be
addressed either from 00001 or 40001 base.
Reg
(hex)
MHR (dec)
RW
Description
Supported values (dec)
Default
0x0004
(4)0005
RW
Slave ID (net address) *
1...247 **
1
0x0005
(4)0006
RW
Baud Rate *
1200, 2400, 4800, 9600, 19200,
38400, 57600
9600
0x0006
(4)0007
RW
Response delay, ms
1...255
10
0x0007
(4)0008
RW
Stop bits, parity bit *
1 no parity bit, 1 stop bit
(default after factory reset)
2 no parity bit, 2 stop bits
3 odd parity, 1 stop bit
4 even parity, 1 stop bit
NOTE: 3 and 4 are available
starting from the Software
version 0x214 (dec. 532)
1
10
Table des matières
Autres manuels Evikon Émetteur
Evikon
Evikon PluraSens E2618-O2-L Manuel utilisateur
Evikon
Evikon PluraSens E2638-Cl2 Manuel utilisateur
Evikon
Evikon PluraSens E2418DF Manuel utilisateur
Evikon
Evikon PluraSens E2658-O3 Manuel utilisateur
Evikon
Evikon PluraSens E2648-CO2 Manuel utilisateur
Evikon
Evikon PluraSens E2670-LEL Manuel utilisateur
Evikon
Evikon E2660-CO-CO2 Manuel utilisateur
Evikon
Evikon E2615-H2S Manuel utilisateur
Evikon
Evikon PluraSens E2618-O2 Manuel utilisateur
Evikon
Evikon E2618-H2S Manuel utilisateur
Evikon
Evikon E2618-NH3 Manuel utilisateur
Evikon
Evikon PluraSens E2648-ETO Manuel utilisateur
Evikon
Evikon PluraSens E2608-N2O Manuel utilisateur
Evikon
Evikon PluraSens E2670-NO2 Manuel utilisateur
Evikon
Evikon PluraSens E2638 Series Manuel utilisateur
Evikon
Evikon PluraSens E2608-Cl2 Manuel utilisateur
Evikon
Evikon E2615-CO Manuel utilisateur
Evikon
Evikon PluraSens E2618 Series Manuel utilisateur
Evikon
Evikon PluraSens E2218 Manuel utilisateur
Evikon
Evikon E2615-NO2 Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
