Evikon PluraSens E2218 Manuel utilisateur
PluraSens®
Humidity & Temperature Transmitter
E2218
User Manual
E2218 Rev 14.05.2021
Table of contents
Specifications 3
Product description 5
Safety requirements 5
Operating conditions 5
Installation and connections 6
Sensor probe handling 9
Delivery set 9
Order code for E2218 options 10
Emergency mode 11
Return to default settings 11
Modbus RTU Communication 12
Communication parameters 13
Modbus holding registers 13
Warranty 17
Manufacturer contacts 17
2
E2218 Rev 14.05.2021
Specifications
Sensors
Digital combined RH and T sensor
Measurement range
0...100 % RH
40...+85 °C or -40...+125 °C (with HT-RP16-H probe)
Resolution
0,1 %RH
0,1 °C
Accuracy
±2,5 % RH / ±0,3 °C
±1,8 % RH / ±0,3 °C on request
Self-diagnostics
Full functionality check at start-up
Warm-up time
≤ 1 s
Response time
~15 seconds
Power supply (Us)
11...30 VDC (nominal 24 VDC) or 24 VAC ±10%
Power consumption
< 1,5 VA
Analog outputs
2 × 4-20 mA / 0-10 V, user settable,
Freely configurable scales
Load resistance
RL< (Us - 2 V) / 22 mA for 4-20 mA
RL> 250 kOhm for 0-10 V mode
Digital interface
RS485, Modbus RTU protocol
no galvanic isolation
Cable connections
Screwless spring loaded terminals
Probe connector
Round industrial M12, IP68
Standard probe
HT-RP16: grey painted aluminium body Ø16 × L90 mm,
IP54 protection, 0...100% RH, -40...+85°C
Probe extension cables
RPEC-2: PVC-insulated, M12 plug and socket, 2.5 m
RPEC-5: PVC-insulated, M12 plug and socket, 5.0 m
Enclosure
Grey ABS, wall mount, protection class IP65
Dimensions
H82 × W80 × D55 mm
Weight
<450 g
Operating environment
Residential and office indoor spaces
Operating conditions
-40...+85 °C, 0...100 %RH without aggressive gases (for main unit)
CE marking
According to 2014/30/EU:
EN 61000-6-3:2020, EN 61326-1:2013(EMC, emissions)
EN 61000-6-1:2019, EN 61000-6-2:2019(EMC, Immunity)
3
E2218 Rev 14.05.2021
Probe options
Standard probe
HT-RP16: grey painted aluminium body Ø16 × L90 mm,
IP54 protection, 0...100% RH, -40...+85°C
Micro probe
HT-RP04:
stainless steel body Ø4 ×50 mm, IP54 protection, 0...100% RH, -40...+85 °C
attached PVC-insulated cable 2 or 5 m
Heavy duty probe
HT-RP16-H:
black painted aluminium body Ø16 × L90 mm,
IP54 protection, 0...100% RH, -40...+125°C
attached PTFE-insulated cable 2 or 5 m
4
E2218 Rev 14.05.2021
Product description
Humidity and temperature transmitter E2218 is a member of the new PluraSens® family of
multifunctional measurement instruments. The transmitter is intended for measurement of
relative humidity and temperature in air and non-aggressive gases with high accuracy and
stability. Absolute humidity and dew point values can be found as well.
The instrument utilises digital fully calibrated and temperature compensated combined
relative humidity and temperature sensors with excellent repeatability and stability. Thanks
to the digital interface the sensor probes are detachable and fully interchangeable. The
range of probes for different applications may be attached to the main unit using standard
water- and dustproof M12 connectors.
Two freely configurable 4-20 mA or 0-10 V analog outputs can be used to connect the
transmitter to secondary instruments. Each output can be independently assigned either to
temperature, relative humidity or dew point channel. RS485 interface with
industry-standard Modbus RTU protocol allows direct Fieldbus networking of the
transmitter.
Safety requirements
Always adhere to the safety provisions applicable in the country of use.
Do not perform any maintenance operation with the power on. Do not let water or foreign
objects inside the device.
Operating conditions
The device should be used in explosion-safe (non ATEX -rated) indoor areas, without
aggressive gases in the atmosphere. Allowed conditions are:
– Temperature in the range of -40...+85 °C;
– Relative humidity in the range of 0...100%;
– Atmospheric pressure in the range of 84...106,7 kPa.
5
E2218 Rev 14.05.2021
Installation and connections
Connect the sensor probe to the device main unit directly or via connecting cable.
Mark and drill four mounting holes on the wall at the chosen mounting place (see
dimensional drawing).
Unscrew four lid screws and detach the lid from the instrument. Fix the transmitter through
mounting holes by screws.
Plug the power cable and connect the analog outputs and/or digital interface terminals to
the relevant devices according to the connection diagram and table.
6
E2218 Rev 14.05.2021
PCB without PSU and relays
Jumpers
J1
OUT1 type (open: 4-20 mA; closed 0-10 V)
J2
OUT2 type (open: 4-20 mA; closed 0-10 V)
X6
Reset Modbus network parameters to default
X4 terminals
OUT1
4-20 mA / 0-10 V output
OUT2
4-20 mA / 0-10 V output
0V
0 V / 24 VAC Neutral (optional)
A
RS485 A / Data +
B
RS485 B / Data -
+U
+24 VDC / 24 VAC Phase (optional)
7
E2218 Rev 14.05.2021
Make certain that the cable gland is properly tightened to ensure the conformity to IP65
protection class.
The screwless quick connect spring terminals on the E2218 are suitable for a wide range
of wires with cross-section 0,2...1,5 mm2. The recommended wire stripping length is 8...9
mm. Push the spring loaded terminal lever, insert the wire end into the terminal hole and
release the lever.
Use twisted pair cable, e.g. LiYY TP 2×2×0,5 mm2 or CAT 5, to connect the device to the
RS485 network. Use one pair for A and B wires and the second pair for common 0V and
power +U wires. to connect the transmitter to the Fieldbus network.polarity must be
respected when connecting to an external RS485 network.
Overall length of all connections via RS485 interface should not exceed 1200 m.
Place the lid back and tighten it with the four screws.
Both analog outputs can be independently changed between 4-20 mA and 0-10 V type
using jumpers J1 (OUT1) and J2 (OUT2). By closing pins on a specific jumper the related
output is 0-10 V, with an open jumper the output is 4-20 mA. Power restart is required after
changing the position of the jumpers.
By default the output OUT1 is assigned to relative humidity with default scale 0-100 %RH.
By default the output OUT2 is assigned to temperature with default scale 0-100 °C.
The output assignments and scales can be changed by Modbus commands.
8
E2218 Rev 14.05.2021
Sensor probe handling
The sensor probes HT-RP16 and HT-RP16H are equipped with a hydrophobic microporous
PTFE filter to protect the sensor from dust, dirt and water drops. The round filter is
snap-fitted and may be replaced if it gets strongly contaminated.
To replace the PTFE filter, carefully hook the filter near it’s edge with a small flat
screwdriver and pull it off. Place a new filter onto the sensor opening and press it to snap
into the groove.
Note! Never stab or press the filter near its center where the sensor is located, as this may
damage the sensor. Do not remove the filter as it may cause the device to show incorrect
values and/or break the sensor.
The recommended orientation of the sensor probe is vertical with the sensor tip pointing
downwards. This prevents possible accumulation of condensed water on the sensor
protection filter. The horizontal orientation is also suitable. Avoid upward position of the
sensor tip.
After replacing the sensor probe check if the M12 connector is securely tightened to
ensure appropriate electrical contact and protection.
9
E2218 Rev 14.05.2021
Delivery set
●Humidity and temperature transmitter E2218
●Set of mounting accessories (4 screws with plastic dowels)
Order code for E2218 options
E2218 options
Order code
With attached probe, -40...+85 °C
E2218-RP16
Duct mount, with stem Ø15×L200 mm, -40...+85 °C
E2218-DM
With remote probe, PVC cable 2,5 m, -40...+85 °C
E2218-RP16-2
With remote probe, PVC cable 5,0 m, -40...+85 °C
E2218-RP16-5
With micro remote probe Ø4×50 mm, 2,5 m PVC cable,
-40...+85 °C
E2218-RP04-2
With micro remote probe Ø4×50 mm, 5,0 m PVC cable,
-40...+85 °C
E2218-RP04-5
With remote probe, fluoroplast cable 2,5 m, -40...+125 °C
E2218-RP16H-2
With remote probe, fluoroplast cable 5,0 m, -40...+125 °C
E2218-RP16H-5
High accuracy ±1,8 %RH
E2218-A
10
Table des matières
Autres manuels Evikon Émetteur
Evikon
Evikon PluraSens E2638 Series Manuel utilisateur
Evikon
Evikon PluraSens E2660-CO-NO2 Manuel utilisateur
Evikon
Evikon PluraSens E2638 Series Manuel utilisateur
Evikon
Evikon PluraSens E2618-O2 Manuel utilisateur
Evikon
Evikon E2615-LEL Manuel utilisateur
Evikon
Evikon PluraSens E2670-Cl2 Manuel utilisateur
Evikon
Evikon PluraSens E2648-NO2 Manuel utilisateur
Evikon
Evikon PluraSens E2638-Cl2 Manuel utilisateur
Evikon
Evikon PluraSens E2618 Series Manuel utilisateur
Evikon
Evikon PluraSens E2638-C2H4 Manuel utilisateur
Evikon
Evikon PluraSens E2611-HFC Manuel utilisateur
Evikon
Evikon PluraSens E2638-HFC Manuel utilisateur
Evikon
Evikon PluraSens E2648-NH3-S Manuel utilisateur
Evikon
Evikon PluraSens E2618-Cl2 Manuel utilisateur
Evikon
Evikon PluraSens E2660-CO-NO Manuel utilisateur
Evikon
Evikon PluraSens E2618 Series Manuel utilisateur
Evikon
Evikon PluraSens E2648-C2H4 Manuel utilisateur
Evikon
Evikon PluraSens E2658 Series Manuel utilisateur
Evikon
Evikon PluraSens E2618-C2H4 Manuel utilisateur
Evikon
Evikon PluraSens E2608-H2S Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
