ETC XDLT 26 Manuel utilisateur

ETC Installation Guide

XDLT 26°/36° Lens Tube Front Lens Kit

Corporate Headquarters nMiddleton, WI, USA |+1 608 831 4116

New York, NY |Orlando, FL |Los Angeles, CA |Austin, TX

Web etcconnect.com |Support support.etcconnect.com |Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7462M2150 Rev A Released 2022-09

Secure the Front Lens

This kit secures the front lens in your 26° or 36° XDLT lens tube using a new lens bracket and screws

with pre-applied LOCTITE®threadlocker.

Tools required:

• 4.5 mm hex key (for accessory door)

• T20 TORX®screwdriver (for lens tube housing)

• #1 Phillips screwdriver (for lens bracket)

1. Remove the lens tube from the fixture,

and place the lens tube on a flat surface

with the front lens facing up.

2. Remove the beam focus knob and

washer, and remove the screw and spacer

on the opposite side of the lens tube.

Remove

knob,

washer,

spacer, and

screw

3. Open the accessory door. Use the 4.5 mm

hex key to remove the two hinge screws

securing the accessory door, taking care

to hold and then retain each spring as

your remove the hinge screw on that side.

Then remove the accessory door.

Open door, and

remove hinge

screws while

holding springs

ETC Installation Guide

XDLT 26°/36° Lens Tube Front Lens Kit

XDLT 26°/36° Lens Tube Front Lens Kit Page 2 of 3 ETC

4. Place the lens tube on a flat surface with

the front lens facing out.

5. Use the T20 TORX screwdriver to remove

the four screws that secure the two halves

of the lens tube housing, and then

remove the top half of the lens tube

housing. Note the two nuts that are

nested in the lower lens tube housing,

where you removed the beam focus knob

and screw in step 2.

Remove screws,

and then remove

top housing

Retain

two nuts

6. Remove the front lens and place it

facedown on a flat, soft surface.

7. Use the #1 Phillips screwdriver to remove

the three screws and bracket as shown at

right.

8. Secure the new bracket to the lens with

the provided LOCTITE screws.

Remove old screws and

bracket, and replace with

new screws and bracket

9. Restore the front lens in the lens tube.

10. Verify that the two nuts for the beam

focus knob and opposing screw are still

nested in the lower lens tube housing.

Restore

lens

Verify

position

of nuts

ETC Installation Guide

XDLT 26°/36° Lens Tube Front Lens Kit

XDLT 26°/36° Lens Tube Front Lens Kit Page 3 of 3 ETC

11. Restore the upper lens tube housing, and

use the T20 TORX screwdriver to secure it

with the four screws.

Restore top

housing and

secure with

screws

12. Place the lens tube on a flat surface with

the front lens facing up, and the side of

the lens tube with the accessory door

facing you.

13. Insert the hinge screw on the right side

part of the way, and then slide the spring

over the screw end from inside the lens

tube housing. Hold the screw and spring

in place, and then position the accessory

door.

Insert screw into

housing, slip spring

over screw, and then

position door

14. Position the tension spring on the left side

and hold it in place, and then insert the

screw into the housing and the spring.

15. Use the hex key to tighten both hinge

screws.

Insert tension spring

and hold in place, and

then insert screw

16. Restore the beam focus knob and washer,

and the screw and spacer on the opposite

side of the lens tube.

Restore

knob,

washer,

spacer, and

screw

Ce manuel convient aux modèles suivants

Autres manuels ETC Équipement d'éclairage

ETC

ETC Lustr+ Manuel utilisateur

ETC

ETC Echo Manuel utilisateur

ETC

ETC D22 Desire series Manuel utilisateur

ETC

ETC Source Four LED 3 Series Manuel utilisateur

ETC

ETC Selador Series Manuel utilisateur

ETC

ETC Source Four Revolution Scroller Cartridge Manuel utilisateur

ETC

ETC ColorSource Spot Manuel utilisateur

ETC

ETC Source Four HID jr Manuel utilisateur

ETC

ETC Aero Wave Station Manuel utilisateur

ETC

ETC fos/4 Panel Yoke Manuel utilisateur

ETC

ETC High End Systems SolaFrame 3000 Manuel utilisateur

ETC

ETC Source 4WRD Manuel utilisateur

ETC

ETC Lighting Control Console Manuel utilisateur

ETC

ETC CE Source Four Manuel utilisateur

ETC

ETC High End Systems SolaPix 19 Manuel utilisateur

ETC

ETC IRIDEON AR500 Manuel utilisateur

ETC

ETC Source Four LED series Manuel utilisateur

ETC

ETC F-Drive W1 Series Manuel utilisateur

ETC

ETC fos/4 Fresnel Manuel utilisateur

ETC

ETC Acclaim 100 series Manuel utilisateur

ETC

ETC SolarFrame 750 Manuel utilisateur

ETC

ETC Express 24/48 Manuel utilisateur

ETC

ETC Source Four HID PARNel Manuel utilisateur

ETC

ETC Source Four LED Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur