ETC Source Four LED 3 Series Manuel utilisateur

Source Four LED Series 3

User Manual

Version 1.1.0

Part Number: 7462M1200-1.1.0 Rev: A

Released: 2021-08

To view a list of ETCtrademarks and patents, go to etcconnect.com/ip. All other trademarks, both marked

and not marked, are the property of their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents

Table of Contents i

Introduction 1

Help from ETC Technical Services 2

Safety 3

Overview 5

Fixture 5

User Interface 6

Set Up and Focus the Fixture 7

Install the Antenna 7

Install a Shutter Barrel 8

Install a Lens Tube 8

Mount the Fixture 9

Connect Power and Data 9

Focus the Fixture 10

Shape the Beam 11

Use Fixture in DMX Mode 12

Set DMXAddress 13

Set DMXMode 13

DMXModes 13

Set DMX Loss Behavior 15

Use Fixture in Stand-aloneMode 16

Studio Mode 17

Color Mode 18

Effects Mode 19

Preset Mode 20

Set Up Wireless Control 21

Set Up Multiverse Wireless Communication 21

Configure Fixtures Wirelessly Using the Set LightApp 21

Control and Customize the Display 22

Lock the Display 22

Adjust the Display Settings 22

Troubleshooting and Maintenance 23

Troubleshooting Checklist 23

Adjust the Pulse Width Modulation (PWM) 24

Test the Emitters 24

View Diagnostic Data 25

Export Fixture Data for Troubleshooting 25

Restore Default Settings 26

Update Firmware 26

Backup and Restore the Fixture Configuration 27

Store the Antenna 28

Clean the Lens and the Fixture Housing 28

Specifications and Reference 29

Environment 29

Weight 29

Electrical 29

RDM Parameters 30

Fixture Compliance 30

Licensed Software 31

ii Source Four LED Series 3 User Manual

Introduction 1

Introduction

With the Source Four LED Series 3 you get a fixture that breaks through the limitations of

designing with other LED fixtures. Wireless control, NFC from a mobile device, and over a

decade of LED color research come together in this impressive fixture. You get incredible

brightness with the highest quality light and tunability available from an LED profile.

The Source Four LED Series 3 is available in two arrays:

•

Lustr X8: The next generation of the Lustr color system incorporates deep red into the

already amazing x7 mix to create an even more rich, vibrant X8 color palette.

•

Daylight HDR: Years of research resulted in an LED mix that yields the highest quality

tunable white light, optimized for studio use.

Model Array Type Description

S4LEDS3L Lustr X8 Light engine without barrel

S4LEDS3LS Lustr X8 Light engine with barrel

S4LEDS3D Daylight HDR Light engine without barrel

S4LEDS3DS Daylight HDR Light engine with barrel

Source Four LED Series 3,

shown with 26° XDLT lens tube

2 Source Four LED Series 3 User Manual

Help from ETC Technical Services

If you are having difficulties and your problem is not addressed by this document, try the ETC

support website at support.etcconnect.com or the main ETC website at etcconnect.com. If none

of these resources are sufficient, contact ETC Technical Services directly at one of the offices

identified below. Emergency service is available from all ETC offices outside of normal business

hours.

When calling for help, take these steps first:

•

Prepare a detailed description of the problem

•

Go near the equipment for troubleshooting

•

Find your notification number if you have called in previously

ETC, Inc.

Americas

Technical Services Department

3031 Pleasant View Road

Middleton, WI 53562

800-775-4382 (USA, toll-free)

+1-608 831-4116

service@etcconnect.com

ETC GmbH

Germany, Austria, Switzerland,

Eastern Europe, and Russia

Technical Services Department

Ohmstrasse 3

83607 Holzkirchen, Germany

+49 (80 24) 47 00-0

techserv-germany@etcconnect.com

ETC Austin

High End Systems Products

Technical Services Department

2105 Gracy Farms Lane

Austin, TX 78758 USA

800-890-8989 (USA, toll-free)

+1-512 836-2242

hesservice@etcconnect.com

ETC France

France

Zone Urbaparc -

Bâtiment E

6 Boulevard de la Libération

Saint-Denis, 93200

+33 1 4243 3535

techservfrance@etcconnect.com

ETC Ltd

Europe, Middle East, and Africa

Technical Services Department

26-28 Victoria Industrial Estate

Victoria Road,

London W3 6UU England

+44 (0)20 8896 1000

techservltd@etcconnect.com

ETCAsia

Asia

Technical Services Department

Room 1801, 18/F

Tower 1, Phase 1 Enterprise Square

9 Sheung Yuet Road

Kowloon Bay, Kowloon, Hong Kong

+852 2799 1220

techserv-asia@etcconnect.com

Introduction 3

Safety

WARNING: RISK OF ELECTRIC SHOCK! The light source in this luminaire is

not user-replaceable, and must be replaced only by a qualified technician.

Contact ETC Customer Support for assistance.

AVERTISSEMENT : RISQUE DE DÉCHARGE ÉLÉCTRIQUE! La source

lumineuse de ce projecteur n'est pas remplaçable par l'utilisateur et ne doit

être remplacée seulement par un technicien qualifié. Contactez le service

client ETC pour obtenir de l’assistance.

WARNING: Note the following safety warnings before use:

•

Use the fixture in dry locations only, where humidity does not exceed

90 percent (non-condensing).

•

Connect the fixture to a non-dimmable power source in order to avoid

damage to the fixture's internal power supply and other electrical

components. Using a dimmable power source can damage the fixture

and will void the warranty.

•

This product must be installed in accordance with the applicable

installation code by a person familiar with the construction and

operation of the product and the hazards involved.

•

Disconnect the fixture from power and DMX and allow it to cool before

installing accessories or performing any cleaning and maintenance.

•

Only use mounting hardware that is rated for the total weight of the

fixture and accessories.

•

In addition to primary suspension, attach a safety cable (or other

approved safety device) to the fixture. Safety cables must be rated to

support ten times the fixture weight. Consult local standards to ensure

that safety cables meet all requirements.

•

Check that the accessory holder is locked and that any accessory safety

cables are connected before mounting the fixture.

•

When adjusting the fixture tilt, be aware that a lens tube adds weight

to the front of the fixture. Use caution to control unintended fixture

movement when adjusting the fixture tilt.

•

Risk of eye injury. Do not stare directly into the light.

•

Do not operate the fixture without the lens installed.

•

Do not use this fixture with a damaged power lead. If the power lead

(cord set) is damaged, it must be replaced.

•

Do not use this fixture if the lens is deeply scratched or cracked. You

must replace the lens when it is damaged.

4 Source Four LED Series 3 User Manual

AVERTISSEMENT : Prendre connaissance des avertissements de sécurité

suivants avant toute utilisation :

•

Ce produit doit être installé selon le code d'installation pertinent, par

une personne qui connait bien le produit et son fonctionnement ainsi

que les risques inhérents.

•

Débranchez le projecteur de son alimentation et du DMX et laissez-le

refroidir avant d’installer des accessoires ou d’effectuer un nettoyage

ou un entretien.

•

N’utilisez que de la quincaillerie de montage adaptée au poids total

des projecteurs et des accessoires.

•

En plus de la suspension principale, fixez une chaîne de sécurité (ou

tout autre dispositif de sécurité homologué) au projecteur. Les chaînes

de sécurité doivent être en mesure de supporter dix fois le poids du

projecteur. Consultez les normes locales pour vous assurer que les

câbles de sécurité respectent toutes les exigences.

•

Vérifiez que le porte-accessoires est verrouillé et que les élingues de

tous les accessoires sont bien attachées avant de monter le projecteur.

•

Lorsque vous ajustez l'inclinaison de l'appareil, sachez que le nez

optique ajoute du poids à l'avant de l'appareil. Soyez prudent afin de

contrôler des mouvements involontaires du luminaire lors du réglage

de son inclinaison.

•

Risque de lésion oculaire. Ne fixez pas directement la lumière.

•

N’utilisez pas le projecteur sans que la lentille soit installée.

•

Ne pas utiliser ce projecteur avec un cordon d’alimentation

endommagé. Si le cordon d’alimentation (câble) est abîmé, il doit être

remplacé.

•

N’utilisez pas ce projecteur si la lentille présente des rayures ou des

fissures profondes. Il faut remplacer la lentille si elle est abîmée.

The luminaire must be installed at least 0.1m (4.0in)

away from all lighted objects.

Le luminaire doit être installé à au moins 0,1m (4,0po)

de tout objet éclairé.

Do not mount the fixture on or near a flammable

surface.

Ne pas installer le projecteur sur ou à côté d’une surface

inflammable.

Do not stare at the operating light source. Ne pas regarder la source de lumière lorsqu’elle

fonctionne.

This product should not be discarded as unsorted

waste but must be sent to separate collection facilities

for recovery and recycling.

Ce produit ne doit pas être jeté avec les déchets

ménagers mais doit être déposé dans une collecte de

déchets électroniques ou dans un point de collecte.

Overview 5

Overview

Fixture

J J

Source Four LED Series 3,

shown with 26° XDLT lens tube

AYoke tilt-lock: Tilt the fixture as needed, and then turn the tilt-lock clockwise to lock the

position. If necessary, pull the tilt-lock away from the stem to adjust the tilt-lock position.

B Safety cable attachment point: Attach safety cable to the fixture housing.

CAntenna storage accessory:When transporting or storing the fixture, store the wireless

antenna on the yoke to protect it (

page28

D Barrel rotation knob: Loosen to rotate the barrel, and then tighten to secure it (

page11

E Shutters: Use four framing shutters to shape the beam.

FPattern holder slot and accessory slot: Insert an A-size, B-size, or glass pattern holder, and

insert an accessory, such as a drop-in iris or motorized pattern device (

page11

GBeam focus knob: Loosen to adjust the lens tube position, and then tighten to secure it

(

page10

H Accessory holder: Insert a color frame or other accessory, and then lock the holder.

IPower In and Power Thru connectors: powerCON®TRUE1 TOP connectors for power in and

power thru (

page9

J DMX In and DMX Thru connectors: Five-pin XLRconnectors for DMX/RDM in and thru.

KUser interface: View the fixture status, set the DMXaddress and mode, or set stand-alone

options.

Antenna: For use when controlling the fixture using wireless DMX (

page21

). The fixture ships

with the antenna stored in the antenna storage accessory (C). Install before using the fixture

(

page7

MNFC(Near Field Communication) tag: Use the Set Light app to wirelessly configure the fixture,

with or without power applied to the fixture (

page21

6 Source Four LED Series 3 User Manual

User Interface

DMX

Address

Mode

DMX Loss

1/3 Red

001

3 Ch RGB

HLL 2 Min

DMX

ADisplay: The colors of options on the display correspond to the colors of the encoders below the

display (E) and the Intensity encoder to the right of the display(B). See

Display on page1

Intensity encoder:

•

When in DMX mode, press the Intensity encoder to enter Focus mode when focusing the

fixture.

•

When configuring the fixture in one of the stand-alone modes, press the Intensity encoder to

toggle between the current intensity and 0, or turn the Intensity encoder to modify the white

fields on the display. See

Use Fixture in Stand-aloneMode on page16

•

When navigating from the Main Menu screen, turn the Intensity encoder to scroll through

menu options, and then press the Intensity encoder to select a menu option.

CMenu button: Press to view the Main Menu screen and configure the fixture. Press the button

again to return to the previous screen when you are setting configuration options.

Function button: Press the button, use the Intensity encoder to navigate to one of the following

modes, and then press the Intensity encoder to select it:

•

DMX:View and set DMX parameters for the fixture.

•

Studio: Use one of three studio (white light) presets, or customize the presets.

•

Color: Use one of 12 color presets, or customize the presets.

•

Effects:Use a sequence, or customize a sequence.

•

Preset: Use one of 12 presets (color preset + fade time), or customize the presets.

See

Use Fixture in Stand-aloneMode on page16

and

Use Fixture in DMX Mode on page12

Encoders(Red, Green, Blue):The colors of encoders correspond to options on the display.

Press to activate the options at the bottom of the display, or turn to modify the values on the

display.

FUSB port: Use for updating firmware, saving and loading fixture configuration settings, or

saving error logs via a flash drive. See

Troubleshooting and Maintenance on page23

GUI lock: Set this switch to lock the UI. This prevents inadvertent changes to the UI. See

Lock the

Display on page22

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ETC Équipement d'éclairage

ETC

ETC Express 24/48 Manuel utilisateur

ETC

ETC 3 Series Manuel utilisateur

ETC

ETC Source 4WRD II Manuel utilisateur

ETC

ETC Source Four CE 405 Manuel utilisateur

ETC

ETC Express 24/48 Manuel utilisateur

ETC

ETC Acclaim 100 series Manuel utilisateur

ETC

ETC Cyberlight LED Manuel utilisateur

ETC

ETC Aero Wave Station Manuel utilisateur

ETC

ETC Source Four Revolution Rotating Wheel Module Manuel utilisateur

ETC

ETC fos/4 Series Manuel utilisateur

ETC

ETC Source Four PARNel CE Manuel utilisateur

ETC

ETC High End Systems SolaPix 19 Manuel utilisateur

ETC

ETC ColorSource PAR Manuel utilisateur

ETC

ETC ColorSource Raceway Manuel utilisateur

ETC

ETC source four fresnel Manuel utilisateur

ETC

ETC Irideon WLZ Manuel utilisateur

ETC

ETC Desire D40XTI Manuel utilisateur

ETC

ETC Hog 4 Series Manuel utilisateur

ETC

ETC HIGH END SYSTEMS LONESTAR Manuel utilisateur

ETC

ETC GDS CueSystem Manuel utilisateur

ETC

ETC Lustr+ Manuel utilisateur

ETC

ETC High End Systems SolaPix 7 Manuel utilisateur

ETC

ETC ArcSystem Pro Multi-Cell RDM Manuel utilisateur

ETC

ETC fos/4 Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur