ETC Source Four LED Series Manuel utilisateur
Copyright © 2011 Electronic Theatre Controls, Inc.
All Rights reserved.
Product information and specifications subject to change.
Part Number:
7064M1200
Rev A
Released: 2011-07
User Manual
Rev A
Source Four®Fresnel
ETC permits the reproduction of materials in this manual only for non-commercial purposes. All other rights are
reserved by ETC.
ETC intends this document, whether printed or electronic, to be provided in its entirety.
ETC
®
, Emphasis
®
, Expression
®
, Insight™, Imagine™, Focus™, Express™, Unison
®
, Obsession™ II, ETCNet2™,
EDMX™, Source Four
®
, Revolution
®
, Sensor® are either registered trademarks or trademarks of Electronic
Theatre Controls, Inc. in the United States and other countries.
All other trademarks, both marked and not marked, are the property of their respective owners.
i
Table of Contents
Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Lamp Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
HPL Lamp Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installing and Replacing the Lamp. . . . . . . . . . . . . . . . . . . . . . . .3
Field Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Accessory Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Yoke Balance Point Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Fixture Angle Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Replacing the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Cleaning the Glass Lens and Reflector . . . . . . . . . . . . . . . . . . .11
ii
Basic Assembly 1
Basic Assembly
Figure-1 Source Four Fresnel fixture components.
WARNING:
Please note the following safety warnings before use:
Do not use this fixture with a damaged power lead. If the power lead
(cordset) is damaged, it must be replaced.
Do not mount the fixture on or near combustible surfaces.
Do not operate the fixture without a lens installed.
Always hang the fixture with the accessory door in the locked position.
Field angle adjustment
knob
Yoke
Color frame holder
Fresnel lens
Safety screen
(CE markets only)
Lamp holder base
Accessory holder door
Lamp door
Lamp
2Source Four Fresnel User Manual
Lamp Information
HPL Lamp Table
CAUTION:
Do not use lamps other than the HPL in Source Four fixtures. Use of lamps other
than HPL will void UL/cUL safety compliance and your warranty.
Lamp code Watts Volts Initial Lumen Color temp. Average rated life
HPL 550/77* 550 77 16,170 3,250° 300 hours
HPL 550/77X* 550 77 12,160 3,050° 2000 hours
HPL 750/115 750 115 21,900 3,250°K 300 hours
HPL 750/115X 750 115 16,400 3,050° 1500 hours
HPL 575/115 575 115 16,520 3,250°K 300 hours
HPL 575/115X 575 115 12,360 3,050°K 2000 hours
HPL 375/115 375 115 10,540 3,250°K 300 hours
HPL 375/115X 375 115 8,000 3,050°K 1000 hours
HPL 750/120 750 120 21,900 3,250°K 300 hours
HPL 750/120X 750 130 16,400 3,0500°K 1500 hours
HPL 575/120 575 120 16,520 3,250°K 300 hours
HPL 575/120X 575 120 12,360 3,050°K 2000 hours
HPL 750/230 750 230 19,750 3,200°K 300 hours
HPL 750/230X 750 230 15,600 3,050°K 1500 hours
HPL 575/230 575 230 14,900 3,200°K 400 hours
HPL 575/230X 575 230 11,780 3,050°K 1500 hours
HPL 375/230X 375 230 7,250 3,000°K 1000 hours
HPL 750/240 750 240 19,750 3,200°K 300 hours
HPL 750/240X 750 240 15,600 3,050°K 1500 hours
HPL 575/240 575 240 14,900 3,050°K 400 hours
HPL 575/240X 575 240 11,780 3,050°K 1500 hours
HPL 375/240X 375 240 7,250 3,000°K 1000 hours
* To be used with ETC Dimmer Doubler™
Lamp Information 3
Installing and Replacing the Lamp
A lamp must be installed before you use the fixture.
Figure-2 Lamp door on bottom of the fixture.
Step 1: Disconnect power to the fixture before installing or replacing the lamp.
Step 2: On the bottom of the fixture, turn the latch on the lamp door one-quarter turn and then
open the door.
Step 3: Remove the lamp holder assembly by turning the knurled knob counterclockwise to
release the lamp socket assembly.
Note:
Verify that the HPL lamp you intend to install is suitable for your facility’s voltage;
115-, 120-, 230-, and 240-volt HPL lamps are available.
See HPL Lamp Table, page 2. Operating HPL lamps above their rated voltage
reduces lamp life and can cause premature lamp failure.
WARNING:
Unplug the fixture and allow it to cool down before attempting to change the
lamp.
Lamp door latch
Lamp door
4Source Four Fresnel User Manual
Step 4: Twist the lamp socket assembly counterclockwise one quarter turn and remove from the
fixture.
Figure-3 Remove lamp with quarter turn counterclockwise.
Step 5: If replacing a lamp, carefully remove the old lamp from the lamp socket assembly.
Step 6: Holding the new HPL lamp by the base, remove it from its box.
.
Step 7: Align the flat sides of the lamp base with the retention brackets on either side of the
socket in the lamp holder assembly as shown in Figure-3.
CAUTION:
The socket assembly remains connected to the fixture by means of its electrical
leads. Do pull or place undue stress on the wired assembly.
CAUTION:
Use caution when installing or replacing any lamp.
When installing and replacing lamp, be sure to point the lamp away from your face
and away from others before inserting it firmly into the assembly.
This may prevent injuries if the lamp should break.
Note:
To avoid premature lamp failure, do not touch the lamp glass. If you do, clean it
carefully with isopropyl alcohol and a clean lint-free cloth. Allow to dry before
operation.
Lamp holder
assembly
Turn to
remove
INCORRECT
CORRECT
Lamp Information 5
Step 8: Push down on the lamp base until the lamp seats firmly. When properly installed, the top
of the lamp’s base will be even with the top edges of the retention brackets.
Step 9: Reinstall the lamp holder assembly into its socket in the fixture so that the arrow points
towards the “unlock” icon on the socket.
Step 10: Turn the lamp holder assembly clockwise one-quarter turn so that the arrow points to the
“lock” icon.
Step 11: Turn the knurled knob clockwise to secure the lamp holder assembly.
Step 12: Close the lamp housing door and turn the latch to secure the door.
CAUTION:
Improperly installed lamps and lamp holder assemblies cause premature lamp
failure and socket problems.
6Source Four Fresnel User Manual
Field Angle Adjustment
You can adjust the field angle of the fixture from 20 to 65° with the field angle adjustment knob.
Step 1: Lift the locking lever to unlock the field angle adjustment knob.
Figure-4 Field angle adjustment knob and locking lever.
Step 2: Do one of the following.
• To reduce the field angle, turn the focus dial counterclockwise.
• To enlarge the field angle, turn the focus dial clockwise.
Figure-5 Field Adjustment from flood to spot.
Step 3: To lock the focus dial, press the locking lever into place.
CAUTION:
The focus knob does not rotate 360°. Do not attempt to exceed limit.
Locking lever
Field angle
adjustment knob
Focus knob in
flood position
Focus knob in
spot position
65° field angle
20° field angle
Autres manuels pour Source Four LED Series
13
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels ETC Équipement d'éclairage
ETC
ETC Source Four Mini CE Manuel utilisateur
ETC
ETC Sensor IQ Contact Input Control Option Card Manuel utilisateur
ETC
ETC Source Four LED Series Manuel utilisateur
ETC
ETC Expression 2.0 Manuel utilisateur
ETC
ETC fos/4 Fresnel Manuel utilisateur
ETC
ETC SolarFrame 750 Manuel utilisateur
ETC
ETC microVision FX Manuel utilisateur
ETC
ETC ArcSystem Pro Multi-Cell RDM Manuel utilisateur
ETC
ETC GDS BluesSystem Manuel utilisateur
ETC
ETC GDS CueSystem Manuel utilisateur
ETC
ETC Desire Fresnel Manuel utilisateur
ETC
ETC ColorSource Spot VXT Manuel utilisateur
ETC
ETC Express Manuel utilisateur
ETC
ETC ColorSource Raceway Manuel utilisateur
ETC
ETC ArcSystem Pro One-Cell Series Manuel utilisateur
ETC
ETC Sensor IQ DALI Control Option Card Manuel utilisateur
ETC
ETC Source Four jr Manuel utilisateur
ETC
ETC Source Four Revolution Scroller Cartridge Manuel utilisateur
ETC
ETC ColorSource CYC Manuel utilisateur
ETC
ETC Irideon WLZ Manuel utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
