ETC ArcSystem Pro One-Cell Series Manuel utilisateur

ETC Installation Guide

ArcSystem Pro One-Cell

Corporate Headquarters Middleton, WI, USA +1 608 831 4116 London, UK +44 (0)20 8896 1000

Holzkirchen, DE +49 (80 24) 47 00-0 Rome, IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 Paris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7491M2110 Rev D Released 2020-01

Introduction

Congratulations on your purchase of ArcSystem products. ArcSystem is a family of overhead LED

products designed for installations where dimming, light quality, and ease of installation are

absolutely essential. With ArcSystem, you will experience perfectly smooth dimming from 100%

down to absolute zero. ArcSystem luminaires come in a variety of form factors, beam angles, and

color-temperature options, all with high-efficiency optics and an outstanding quality of light ideal for

any application.

ArcSystem products with ArcMesh can be controlled using wired DMX or the wireless ArcMesh

protocol. ArcSystem products without ArcMesh can be configured for RDMcontrol. This manual

provides step by step instruction on the installation of ArcSystem products as well as full system

integration. For information on installing the ArcSystem TX1 Transmitter for use with ArcMesh

installations, see the ArcSystem Installation Manual at etcconnect.com/ArcSystem. All ETCmanuals

are available for download free of charge at etcconnect.com.

Safety

ArcSystem products are intended for professional use only. Read the entire manual before using this

equipment.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including

the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

•

Do not use outdoors.

•

Do not let power supply cords touch hot surfaces.

•

Do not mount near gas or electric heaters.

•

Equipment should be mounted in locations and at heights where it will not readily

be subjected to tampering by unauthorized personnel.

•

The use of accessory equipment not recommended by the manufacturer may cause

an unsafe condition.

•

Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 2 of 29 ETC

System Overview

ArcSystem luminaires are available in 100–240 V standard models with IEC connectors, 100–125 V

emergencymodels with NEMA5-15 connectors, or 100–277 V hard-wired standard or emergency

models. ArcSystem Pro One-Cell luminaires require an external driver.

ArcSystem Pro One-Cell

•

external 100–277 V D1 Series or D4 Series

driver required

•

ideal for short/medium throw

•

25 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

yoke mount version with two-axis tip and tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Small

•

external 100–277 V D1 Series or D4 Series driver

required

•

ideal for short/medium throw

•

25 W full load power consumption

•

adjustable version recessed/flush mount with

single-axis tilt

•

yoke mount version with single-axis tilt

•

beam angle options: 19°, 24°, 37°, 60°

ArcSystem Pro One-Cell High Output

•

external 100–277 V D1 HO driver required

•

ideal for long throw

•

100 W full load power consumption

•

fixed version recessed/flush mount only

•

adjustable version recessed/flush mount with

two-axis tip and tilt

•

beam angle options: 18°, 30°, 50°

ArcSystem Pro One-Cell Micro

•

external 100–277 V D2 driver required

•

ideal for short/medium throw

•

20 W full load power consumption

•

adjustable version recessed/flush mount with two-

axis tip and tilt

•

yoke mount version with two-axis tip and tilt

•

beam angle options: 19°, 24°, 37°, 60°

Note:

The ArcSystem Pro One-Cell Micro is not available in 5000 K or Fade to Warm

variants. The ArcSystem Pro One-Cell High Output is not available in 3500K, 4000K,

5000K, or Fade to Warm variants.

ArcSystem Pro Multi-Cell luminaires are covered in the

ArcSystem Pro Multi-Cell Installation Guide

and

ArcSystem Installation Manual

. All ETCmanuals are available for download free of charge at

etcconnect.com.

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 3 of 29 ETC

D1 Series, D2 Series, and D4 Series Drivers

D1 Driver

D1 HO Driver

D2 Driver D4 Driver

Note:

Antenna is not present on RDM models.

ArcSystem Pro One-Cell luminaires require an external driver. ArcSystem D1, D2, and D4 Series

drivers use standard RJ45 connectors for DMXcontrol.

•

The D1 Driver provides up to 25 W to a single One-Cell or One-Cell Small luminaire.

•

The D1 HO Driver provides up to 100 W to a single One-Cell High Output luminaire.

•

The D2 Driver supports one or two One-Cell Micro luminaires and provides up to 10 W per

output.

•

The D4 Constant Current Driver with Molex connectors supports four One-Cell or One-Cell

Small luminaires.

•

The D4 Constant Current Driver with terminals provides 48 VDCand 400 mA or 600 mA per

output channel, with a maximum total output of 2.4 A or 100W.

•

The D4 Constant Voltage Driver with terminals provides 24 VDC and up to 50 W per output

channel, with a maximum total output of 2 Aor 150 W.

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 4 of 29 ETC

For more information on installation of standard or emergency system drivers, see

Preparing to

Install the Driver on page7

Emergency System One-Cell Installation on page19

Note:

ArcSystem Pro One-Cell Micro and ArcSystem Pro One-Cell standard luminaires

are not interchangeable. One-Cell Micro luminaires require a D2 driver to function; One-

Cell and One-Cell Small luminaires require a D1 driver or D4 driver to function.

Note:

All ArcSystem wireless luminaires require a TX1 Transmitter and commissioning

tool to set DMX addresses for both wired DMX and wireless installations. Contact your ETC

Service Technician for more information.

Emergency System Overview

ArcSystem drivers and luminaires can be purchased in UL924 listed variants. Each of the luminaires

can be configured to be UL924 listed when wired into an existing emergency response system. See

Emergency System One-Cell Installation on page19

Install the ArcSystem D1, D2, or D4 Series driver in a location that is accessible by qualified

personnel for testing of the emergency operation.

Note:

Luminaires must be hard-wired to emergency certified drivers to be considered for

UL924 certification.

Note:

The number of designated emergency lamps and their height is the responsibility of

the specifier and installer in order to achieve the minimum FC levels of NFPA101.

Installation scenarios should be evaluated by the AHJ to confirm illuminance and

performance requirements of ANSI/NFPA 101 and the IBC.

Note:

ArcSystem Pro One-Cell Micro luminaires in emergency installations must be

installed with a maximum mounting height of 23.2 ft (7.07 m).

Note:

Installation must follow all national and local codes for electrical equipment.

Note:

Normal and emergency wiring cannot be contained in the same conduit according

to NEC 700.10(B).

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 5 of 29 ETC

Emergency drivers and luminaires require two branch circuit connections. These inputs have the

following functions:

1. Normal branch circuit to sense failure of the normal supply. Connect to Sense Input

connector.

2. Normal/Emergency branch circuit providing power to the luminaire in both conditions.

Connect to Maintained Input connector.

Sense detects when power is lost and forces the luminaire to a full-on state, powered by the

emergency supply through the Constant Power input. Control of the luminaire will not be available

until the sense input has been restored.

WARNING: Do not mix 120 V and 277 V between the sense and emergency

feeds.

AVERTISSEMENT : Ne pas inverser les alimentations à 120V et 277V entre

les alimentations de détection et de secours.

WARNING: Sense (normal) and Maintained (normal/emergency) feeds must

have the same phase. The diagram below shows the recommended installation.

AVERTISSEMENT : Les alimentations de détection (normale) et d’entretien

(normal/secours) doivent être sur la même phase. Le schéma ci-dessous présente

l’installation recommandée.

normal

breaker

panel

ArcSystem multi-cell

emergency luminaire

ArcSystem one-cell

emergency luminaire

with emergency

driver

emergency

breaker

panel

normal branch circuit

used to sense normal power failure

connect to Sense input

normal/emergency branch circuit

normal

normal/emergency

from UL1008

ATS by others

connect to Maintained input

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 6 of 29 ETC

Before You Begin Installation

Review the following sections before beginning your ArcSystem installation. ArcSystem products

should only be installed by a qualified installer or electrician.

Power Disconnect Device

Before installation, make sure you have a readily accessible input power disconnect device installed

ahead of your ArcSystem products.

WARNING: RISK OF DEATH BY ELECTRIC SHOCK! Failure to disconnect all

power to the system before installation, maintenance, cleaning, or any other

system modification could result in serious injury or death.

AVERTISSEMENT : RISQUE DE MORT PAR DÉCHARGE ÉLECTRIQUE! Négliger

de débrancher toutes les sources d’alimentation du système avant l’installation,

l’entretien, le nettoyage ou toute autre modification du système peut causer

des blessures graves ou la mort.

De-energize main feed to ArcSystem and follow appropriate Lockout/Tagout

procedures as mandated by NFPA 70E. It is important to note that electrical

equipment such as breaker panels can present an arc flash hazard if improperly

serviced. This is due to the high amounts of short-circuit current available on

the electrical supply to this equipment. Any work must comply with OSHA Safe

Working Practices.

WARNING: Circuits that are installed without an accessible power disconnect

device cannot be serviced or operated safely.

AVERTISSEMENT : Il est imprudent d'utiliser ou de réparer les circuits

installés sans qu'un dispositif de déconnexion de l'alimentation ne soit

accessible.

Site Survey for Wireless Installations

ArcSystem transmitters and luminaires operate in the unlicensed 2.4 GHz band using the IEEE

802.15.4 standard. This band is shared with other technologies such as Wi-Fi, Bluetooth, low power

sensor networks, wireless AV transmitters and some radio microphones.

Before commissioning a system, a wireless site survey is essential.

Gathering information on how your wireless lighting system will overlap with all other Wi-Fi traffic in

the area will help determine setup of transmitters and which luminaires should be re-broadcasting,

not just receiving wireless data.

Installation Requirements

•

Indoor installation only: 0–40°C (32–104°F), 5–95% non-condensing humidity.

•

Dry locations only.

•

Installation location must support the weight of the luminaire, driver, and applicable mounting

hardware.

CAUTION:

ArcSystem luminaires and drivers are not suitable for use in spaces

with restricted air flow. Enclosing the luminaires or drivers temporarily or

permanently may cause damage to the luminaires or drivers.

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 7 of 29 ETC

Preparing to Install the Driver

D1 Driver

D1 HO Driver

ArcMesh Wireless DMX

D1 DriverTX1 Transmitter

D2 Driver D4 Driver

Note:

Antenna is not present on RDM models.

The D1, D2, and D4 Series drivers are compact, convection-cooled LEDdrivers with RJ45

connections for local DMX. Each driver has an INand THRU option, using two separate connectors.

The D1 and D1 HOdrivers can control a single luminaire each. The D2 driver can control two

ArcSystem Pro One-Cell Micro luminaires. The D4 driver can control up to four ArcSystem Pro One-

Cell or Pro One-Cell Small luminaires. Up to 32 drivers can be installed on one hard-wired line of

DMX.

The following illustration shows an example of a linear ceiling installation with one luminaire for

each D1 Series driver. The cable between an ArcSystem Pro One-Cell Series luminaire and its driver

is approximately 1 m (40 in) long.

Note:

If you want to daisy chain power wiring, it must be connected through a junction

box as shown below. Follow all applicable local and national electrical codes.

DEF

APower connections DScrew mounting locations

BDMXIn and Thru connections ED1 or D1 HOdriver

CFlexible conduit FLuminaire

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 8 of 29 ETC

Installation Spacing - High Output Luminaires

ArcSystem Pro One-Cell High Output luminaires must be installed with the spacings listed below.

Install with minimum spacings between

a. Center-to-center of adjacent luminaires:609.6 mm (24 in)

b. Top of luminaire to overhead building member:76.2 mm (3 in)

c. Luminaire center to side building member:304.8 mm (12 in)

Supplies

The following supplies are required, but not provided:

•

½ in flexible conduit and conduit fittings, as needed

•

Romex or nonmetallic screw-clamp style conduit connectors for outputs

•

Phillips screwdriver

•

Four #10 screws and other mounting hardware as needed

Note:

Mounting hardware and installation location must support the weight of the driver,

conduit hardware, and all cable required for installation.

Electrical and Wiring Specifications

Install the driver on a power distribution system with reliably identified earthed neutral (ground)and

install a maximum 20 A circuit breaker on the line conductor. The D1, D2, and D4 Series drivers

accept 100–277 VAC, 50/60 Hz. ETC recommends installing all wiring in grounded metal conduit.

WARNING: Circuits that are installed without an accessible power disconnect

device cannot be serviced or operated safely.

AVERTISSEMENT : Il est imprudent d'utiliser ou de réparer les circuits

installés sans qu'un dispositif de déconnexion de l'alimentation ne soit

accessible.

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 9 of 29 ETC

Wire and Terminal Specifications

Terminal/Connector Conduit

Entry Wire Range/Specifications Strip

Length Torque Rating

D1 power input

line/neutral/ground

½ in

conduit Up to 6mm2(10AWG) solid or stranded 7 mm

(1/4 in)

0.8 Nm

(7 in-lb)

D1 HOand D2 power input

line/neutral ½ in

conduit 0.5–10 mm2(22–6 AWG) 7 mm

(1/4 in)

0.5 Nm

(4.4 in-lb)

D4 maintained power input

line/neutral

D4 emergency drivers

sense power input

line/neutral/ground

½ in

conduit 0.2–2.5 mm2(24–14 AWG) 6.5 mm

(1/4 in)

0.5–0.6 Nm

(4.4–5.3 in-lb)

Power Input

ground

½ in

conduit 2.5–10 mm2(6–14 AWG) 10 mm

(3/8 in)

4.0 Nm

(35 in-lb)

DMX In/Thru

RJ45 Connectors

½ in

conduit

Cat5e (or better) minimum 0.2mm2

(24AWG) conductors terminated to

T568B standard

N/A N/A

Outputs for all D1, D2, and

D4 Series Drivers with Molex

connectors

½ in

conduit Follow Class 2 wiring methods.

Outputs for D4 drivers with

terminals

½ in

conduit

0.2–2.5 mm2(26–14AWG) using the

provided two-terminal connectors.

Follow Class 1 wiring methods.

6mm

(1/4 in)

0.4–0.5Nm

(3.5–4.4in-lb)

Note:

Maximum supported wire length between One-Cell luminaires and D1 Series and

D2 Series drivers is 15m (49ft).

Maximum supported wire length between any load and a D4 Series driver is 10m (33ft).

Mounting the Driver

Depending on your installation, you might want to surface-mount the driver. Any ArcSystem

standalone driver can be surface-mounted to any surface capable of supporting its weight using the

four holes located on the back side of the enclosure. Contact ETC for custom mounting bracket

options.

1. Remove the two screws on the cover of the driver and set them aside.

2. Removethe driver cover. The cover is tethered to the backbox. Be careful when handling.

Note:

If you are installing a D1 High Output driver, the power supply is inside the cover

and has wiring that runs to the driver board in the back panel of the driver. Be careful when

handling. It may help to nest the back panel of the driver inside the cover as shown in

Wiring the Driver and Luminaire on page12.

3. Using four #10 screws, mount the back panel to the mounting surface.

4. Attach flexible conduit to the driver. There are four conduit knockouts available.

5. Install Romex or nonmetallic screw-clamp conduit connectors to output knockouts, as needed.

ETC Installation Guide

Pro One-Cell

Pro One-Cell Page 10 of 29 ETC

Note:

Make sure that the flexible electrical supply can extend through the ceiling

opening so that the driver and luminaire can be inspected and serviced when needed.

Note:

Use suitable conduit where required by national and local codes.

Note:

Drivers may require additional means of securement. Installation must follow all

national and local codes for electrical equipment.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ETC Équipement d'éclairage

ETC

ETC Expression 2.0 Manuel utilisateur

ETC

ETC Source Four PARNel CE Manuel utilisateur

ETC

ETC Prodigy FlyPipe Studio Manuel utilisateur

ETC

ETC Sensor IQ DALI Control Option Card Manuel utilisateur

ETC

ETC ArcSystem Pro Multi-Cell RDM Manuel utilisateur

ETC

ETC ColorSource Spot Manuel utilisateur

ETC

ETC fos/4 Series Manuel utilisateur

ETC

ETC ELTS2 Manuel utilisateur

ETC

ETC Desire D40XTI Manuel utilisateur

ETC

ETC fos/4 Fresnel Manuel utilisateur

ETC

ETC Irideon WLZ Manuel utilisateur

ETC

ETC Irideon AR50 Manuel utilisateur

ETC

ETC Source 4WRD Manuel utilisateur

ETC

ETC GDS CueSystem Manuel utilisateur

ETC

ETC ArcLamp System Manuel utilisateur

ETC

ETC Irideon WLZ Manuel utilisateur

ETC

ETC GDS BluesSystem Manuel utilisateur

ETC

ETC High End Systems SolaPix 19 Manuel utilisateur

ETC

ETC ArcSystem Pro D1 Series Manuel utilisateur

ETC

ETC Source Four Revolution Scroller Cartridge Manuel utilisateur

ETC

ETC fos/4 Panel Pole-Operated Yoke Manuel utilisateur

ETC

ETC ColorSource Spot Manuel utilisateur

ETC

ETC ColorSource Spot jr v2.0 Manuel utilisateur

ETC

ETC Source Four LED Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur