ETC P-TS18 Manuel
ETC Setup and Connect Guide
Unison Paradigm®18 inch Touchscreen
Corporate Headquarters
Middleton, WI, USA
Tel +608 831 4116
London, UK
Tel +44 (0)20 8896 1000
Service: (UK)
Rome, IT
Tel +39 (06) 32 111 683
Holzkirchen, DE
Tel +49 (80 24) 47 00-0
Service: (DE) techserv-hoki@etcconnect.com
Hong Kong
Tel +852 2799 1220
Web: etcconnect.com
© 2018 Electronic Theatre Controls, Inc.
Product information and specifications subject to change. ETC intends this document to be provided in its entirety.
7184M2200
Rev C
Released 2018-02
Overview
Welcome to the Paradigm 18 inch Touchscreen Setup and Connect Guide. The Paradigm 18 inch
Touchscreen (P-TS18) ships standard with a table top stand and an international power supply. Available
separately, ETC offers a 19” rack mounting kit (P-TS18-RK). Contact ETC for ordering details.
This guide provides table top stand and rack mount installation instructions, as well as information related
to the initial setup and connection of the Paradigm 18 inch Touchscreen (P-TS18) including details to
interface with the Application Shell. Instructions for use of the Paradigm Virtual Touchscreen Software are
available on the ETC website at etcconnect.com.
Features
• 100-240 VAC, 50/60Hz
• High-resolution 1366x768p touchscreen interface
• USB interfaces for theme upload or use of a separate mouse and keyboard (if required)
• Two Ethernet ports for connectivity to the Paradigm network
• Runs Paradigm Virtual Touchscreen Software
• Includes table top stand and installation hardware
- Supports panel, wall, desktop, and swing-arm VESA mounting. Accepts screw type M4 x 8-12mm
(VESA mounting kit and installation hardware provided by others)
Operating Environment
• Supports use of 0-40°C, 5-95% at 40°C non-condensing humidity environment
Note:
P-TS18 is only supported by P-CCS software version 3.0 or later.
P-TS18 installed on
table top stand
(included)
P-TS18 installed into a
19” rack mount kit
(P-TS18-RM) available
separately
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 2 of 15 ETC
Table Top Stand Mounting
The table top stand accessory is provided with the Paradigm 18 inch Touchscreen.
1: Locate the table top stand and installation hardware in the main packaging with the touchscreen.
2: Align the table top stand to the back of the touchscreen. Reference the graphic above for
clarification.
3: Secure the stand to the touchscreen using two screws (provided).
4: Locate the international power supply and cables from the touchscreen accessory box.
5: Insert the power supply round plug into the Touchscreen “12V DC IN” receptacle, located on the
back of the unit.
6: Using the appropriate power cable adaptor that is required for your region, insert the receptacle end
into the power supply and the plug end into the power source.
7: Connect an Ethernet cable (not provided) between the P-TS18 “Net3 Network” interface, which is
the left-most RJ-45 connector while viewing the back, and the network switch that is also connected
to the Paradigm Central Control Server (P-CCS).
A. COM1
B. COM 2
C. Line-out
D. Mic in
E. LAN ports x 2 (RJ-45)
F. HDMI
G. USB
H. Power button
I. 12V DC IN input
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 3 of 15 ETC
Rack Mounting
The P-TS18 Touchscreen Rack Mount Kit (P-TS18-RK) provides the ability to install the P-TS18 into a 19”
rack, utilizing eight units (8U) of rack space.
Installations
1: Locate the P-TS18, the accessory box from the P-TS18 packaging, and the P-TS18 Touchscreen Rack
Mount Kit.
2: Using the included locknuts, mount the power supply holder with the power supply installed to the
back of the rack mount panel using a 5/16 nut driver.
3: Attach the rack mount panel to the 19” rack enclosure using the four M10 screws, washers, and the
spring clips provided with the Rack Mount Kit.
4: Carefully remove the plastic trim ring from the back of the touchscreen.
Note:
Full access to the front and back of the equipment rack is required during this installation
procedure.
Note:
The P-TS18 ships with a table top stand which is not required when rack mounting.
Recycle or discard the unused stand parts.
Install
Locknuts
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 4 of 15 ETC
5: To install the P-TS18 into the rack mount panel, insert the top part of the touchscreen into the panel
then gently press the bottom part of the touchscreen into the panel. The touchscreen will be
temporarily held in place by the top and bottom clips on the touchscreen and rack mount panel.
6: Accessing the unit from the rear of the equipment rack, carefully secure the touchscreen to the rack
mount panel using the screws provided.
7: Attach the two USB cables from the rack mount panel to the USB ports on the touchscreen I/O. This
connection allows convenient use of the touchscreen USB ports from the front of the rack mount
panel.
Final Installation
Connect Power and Data
Power
1: Insert the power supply round plug into the “12V DC IN” receptacle located on the back of the
touchscreen.
2: Locate the correct IEC power cable for your region from the P-TS18 accessory box.
3: Attach the IEC cable between the power supply and the power source.
Data
Connect an Ethernet cable (not provided) between the P-TS18 “Net3 Network” interface, which is the left-
most RJ-45 connector while viewing the back, and the network switch that is also connected to the
Paradigm Central Control Server (P-CCS).
Power Up
1: Apply power to the circuit.
2: Reference
P-TS18 Initial Power-up
on
page 5
for further instruction to use the touchscreen and
Virtual Touchscreen Software.
secure
here secure
here
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 5 of 15 ETC
P-TS18 Initial Power-up
The P-TS18 boots as soon as it has power. Because ETC has prepared the P-TS18 at the factory prior to
shipment, on initial power-up, Virtual Touchscreen Software loads.
Application Shell
The Application Shell includes the interface to launch the Virtual Touchscreen Software, which was
installed at the factory before shipment. In addition, the Application Shell provides access to the
touchscreen’s IP and network settings, as well as more advanced features which are password protected.
To continue with selecting a Virtual Touchscreen configuration,
touch to select the “Central Control Server” from the “Discovered
Servers” list. Instructions for use of Paradigm Virtual Touchscreen
Software are available on the ETC website at etcconnect.com.
To update Virtual Touchscreen Software, to change IP or network
settings, or for additional advanced features and troubleshooting,
touch the [Quit] button on the bottom right corner of the VTS
application. The VTS application closes and the Application Shell
displays. Reference
Application Shell
for instructions.
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 6 of 15 ETC
Notice the lower right hand corner of the shell displays software versions of both the “Shell Version” and
the “App Version”. The “App Version” represented is the version of Virtual Touchscreen Software that is
currently installed.
Three tabs are located on the Application Shell including “General”, “Device Setup” and “Advanced”.
General Tab
The “General” tab is provided as the interface to launch and manage the Virtual Touchscreen Software.
[Launch Virtual Touchscreen]
The Virtual Touchscreen Setup Guide is available for download on the ETC website at etcconnect.com.
Install Management
This section of the “General” tab provides the ability to [Uninstall] Virtual Touchscreen Software or install
a newer version from either removable media or the connected Paradigm Central Control Server (P-CCS).
Note:
The Application Shell software is included with each installation of the P-TS18. Updates
to the shell are combined with VTS application updates when necessary.
Note:
Touchscreen configurations are created in ControlDesigner and associated to a Virtual
Touchscreen instance in LightDesigner. Reference the online help systems for
ControlDesigner and LightDesigner for details to create and associate touchscreen
configurations.
Note:
If a current version of VTS is installed, the [Install from Removable Media] and [Install from
Online P-CCS] buttons are disabled. You must first uninstall the software before installing
a new version. Reference [Uninstall] for details.
To launch the Virtual Touchscreen Software touch the
[Launch Virtual Touchscreen] button located on the
“General” tab.
The VTS application launches to the “Discovered Servers”
list. Select the Central Control Server to continue with
configuration selection.
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 7 of 15 ETC
[Uninstall]
Only one instance of Virtual Touchscreen Software can be installed at a time. You must uninstall any
currently installed software before installing another.
1: Touch to select [Uninstall]. The password dialog displays for password entry.
2: Enter the password into the provided space then touch [Enter]. The Paradigm Virtual Touchscreen
Bundle Uninstall wizard displays for confirmation.
[Install from Removable Media]
Virtual Touchscreen Software installs from removable media (typically USB device). You can retrieve the VTS
application file from the web interface of a connected Paradigm Central Control Server (reference the
documentation for the P-CCS for instructions). You must save the VTS software executable
(“paradigm_vts_installer.exe”) to the root directory of the removable media.
1: Insert the removable media into a USB interface of the Paradigm 18 inch Touchscreen.
2: Touch [Install from Removable Media]. The application wizard will automatically begin installation of
the VTS application. During this installation process, the touchscreen will shut down then restart
again, automatically launching VTS at restart. For instructions on use of Virtual Touchscreen
Software, reference the Paradigm Virtual Touchscreen Setup Guide, available for download on the
ETC website at etcconnect.com.
Note:
The password is set, by factory default, to 4116. Change this password or remove the
requirement for a password in the [Set Password] section of the Advanced Tab.
Note:
P-TS18 is supported by P-CCS version 3.0 software or later.
Note:
The paradigm_vts_installer.exe file must be stored on the root directory of the USB
device.
3: Touch the [Uninstall] button to proceed with the
uninstall process.
4: Touch [Finish] to close the wizard. The Application
Shell returns to the “General” tab where you can
proceed to install another version of the VTS
application from either removable media or an
online Paradigm Central Control Server (P-CCS).
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 8 of 15 ETC
[Install from Online P-CCS]
Virtual Touchscreen Software installs from any discovered and online Paradigm Central Control Server (P-
CCS).
1: Touch to select the [Install from Online P-CCS] button.The Application Shell provides a list of all
discovered Central Control Servers (P-CCS) by IP address. Be patient as this process could take up to
a minute depending on network traffic,
2: Touch to select the server IP from the discovered list, then touch the [Install]. During this installation
process, the touchscreen will shut down then restart again, automatically launching the VTS
application at restart. For instructions on use of Virtual Touchscreen Software, reference the
Paradigm Virtual Touchscreen Setup Guide, available for download on the ETC website at
etcconnect.com.
• To cancel the installation and return to the “General” tab, touch [Cancel].
• To request a refreshed list of online and discovered P-CCS, touch [Refresh List].
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 9 of 15 ETC
Device Setup Tab
Common settings that are required to set up your Paradigm 18 inch Touchscreen including the Network
Connection, IP Address, Subnet mask, Gateway, and Volume and Brightness Settings are available on the
“Device Setup” tab.
Network Adaptor and IP Settings
The “Network Adapter” status on the top of the screen indicates whether a valid Paradigm network is
Online
or
Offline
.
The section for “IP Settings” provides TCP/IP v4 settings for the Paradigm 18 inch Touchscreen.
• Network Connections - always defaults to “Net3 Network”, which is the left-most RJ-45 connector
while viewing the back of the unit, which is where the P-TS18 should be connected.
• Settings for the other network connector can be edited if that interface is used instead,
however the correct interface must be selected from the Setup tab of the VTS application.
• Allows for either Automatic or Manual IP settings. Default setting is Manual (IP address:
10.101.18.101, Subnet mask: 255.255.0.0, Gateway: 10.101.1.1).
- Select Automatic when LinkLocal IP (no DHCP) or DHCP.
- Select Manual to manually set the IP address, Subnet mask, and Gateway IP of the Touchscreen.
With “Manual” selected, touch inside each field to set the numeric values.
Note:
Touch the [Save Changes] button before leaving this tab or the changes will be lost.
ETC Setup and Connect Guide
Paradigm 18 inch Touchscreen
P-TS18 Touchscreen Page 10 of 15 ETC
Volume and Brightness and Display Settings
Adjust the volume and brightness settings using the provided sliders. To mute the volume for the
Touchscreen, select the “Mute Sound” checkbox beneath the Volume Settings slider.
Determine the sleep settings for the touchscreen display using the drop down selection box. By default the
display is set to turn off after 15 minutes without user interaction.
Advanced Tab
The “Advanced” tab is password protected by default. The settings and features on this tab are reserved
for technicians and administrators. The password is set, by factory default to 4116. Change the user
configurable password (“4116” always works as a back door) or remove the requirement for a password
using the “
[Set Password]
” feature.
Note:
Touch the [Save Changes] button before leaving this tab or the changes will be lost.
Table des matières
Autres manuels ETC Unité de contrôle
ETC
ETC SmartModule 2 Manuel utilisateur
ETC
ETC ETCpad Manuel utilisateur
ETC
ETC Eos Remote Processor Unit 3 Manuel utilisateur
ETC
ETC UHCI-4 Manuel utilisateur
ETC
ETC EchoTouch Manuel utilisateur
ETC
ETC ColorSource ThruPower Series Manuel utilisateur
ETC
ETC Unison Echo Manuel utilisateur
ETC
ETC EM264 Manuel utilisateur
ETC
ETC Unison Echo Inspire Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
