Escea ST900 Manuel utilisateur

ST900

630297_0_Manual_User_ST900_US

GAS FIREPLACE USER GUIDE

www.escea.com

NORTH AMERICA

Ce manual est disponsible en Français sur demande

SERIAL NUMBER 43000 AND ABOVE

DO NOT PLACE ARTICLES OR FURNISHINGS ON OR AGAINST THIS APPLIANCE.

DO NOT OPERATE THE FIREPLACE IF THE GLASS HAS BEEN BROKEN,

DAMAGED OR IT IS NOT PROPERLY POSITIONED/HOOKED ONTO THE

FIREPLACE.

DO NOT OPERATE THE FIREPLACE WITH THE FASCIA PANELS REMOVED.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM

PERSONS UNLESS THEY HAVE BEEN ADEQUATELY SUPERVISED BY A

RESPONSIBLE PERSON TO ENSURE THAT THEY CAN USE THE APPLIANCE

SAFELY.

T HIS A P P LIA N C E M U S T B E I N S TA LLE D I N AC C O R DAN C E W ITH T HE

MANUFACTURERS WRITTEN INSTRUCTIONS.

THE GLASS SURFACE ON THE FRONT OF THE FIREPLACE IS CONSIDERED A

WORKING SURFACE, AND AS SUCH IS HOT AND CARE MUST BE TAKEN NOT TO

TOUCH THIS SURFACE. IT IS RECOMMENDED A SECONDARY GUARD IS FITTED

IN PLACES WHERE THERE ARE YOUNG CHILDREN OR AGED OR INFIRM

PERSONS.

CURTAINS SHOULD NOT BE POSITIONED ABOVE THE FIREPLACE AND ANY

PROTRUDING LEDGES MUST NOT COME WITHIN THE MINIMUM DISTANCES

SPECIFIED IN PAGE 7 OF THIS USER MANUAL.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN

THE SAME ROOM AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN AND

OTHERS MAY BE SUSCEPTIBLE TO ACCIDENTAL CONTACT BURNS. A PHYSICAL

BARRIER IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUALS IN THE

HOUSE. TO RESTRICT ACCESS TO A FIREPLACE OR STOVE, INSTALL AN

ADJUSTABLE SAFETY GATE TO KEEP TODDLERS, YOUNG CHILDREN AND

OTHER AT RISK INDIVIDUAL OUT OF THE ROOM AND AWAY FROM HOT

SURFACES

The data plate for this appliance, containing technical information and

specifications, can be found in the bottom left corner, near the base of

the fireplace. To access this, the fascia must be removed.

Any installation or service work carried out on this appliance must only

be done by a licenced or qualified service person.

Escea recommends the ST900 is inspected and serviced by a

licenced or qualified service person once every twelve (12) months.

Manufactured By: Escea Ltd, 17 Carnforth Street, Green Island, Dunedin 9018, NZ. Ph: +64 3 4788220

For distribution details see: www.esceasales.com

Quick-Start Guide

Note: You must wait at least two minutes after turning

the ﬁreplace off before attempting to turn the ﬁreplace

on again.

Note: Make sure to avoid pressing more than one

button by using the tips of your ﬁngers when pressing

buttons.

Using the remote handset:

To start your ﬁreplace:

1. Press and hold the button until you hear 2 beeps

and the handset shows a blinking series of lines.

2. Wait until the ﬁre has lit the main burner before any

buttons are pressed.

Two basic ways to change the ﬂame height:

ŸPress and hold or , to range the ﬂame up and

down.

ŸWhile the back-light is ON, you may double tap the

or button to attain a high or low ﬂame respectively.

To turn OFF your ﬁreplace:

Press and hold the button until the screen displays

‘OFF’.

To change the desired room temperature:

1. Press and hold the button until displays and the

numbers on the screen start to ﬂash.

2. Press the and buttons to increase and decrease

the desired room temperature respectively.

3. To conﬁrm press the button and wait.

NOTE: Make sure to install batteries in the remote handset and the receiver

(refer to page 5 of this manual) before operating this ﬁreplace for the ﬁrst time.

Advanced Operation

Setting Fahrenheit or Celsius

Child proof

Setting the Time

Contents

Manual Mode

Designated Low Fire and High Fire

Countdown Timer

Modes of Operation

Thermostatic Mode

Program Mode

Touch Pad Wall Switch

To Turn off Gas to Appliance

Automatic Turn Down

Automatic Shut Off

Installing the Batteries in the Receiver

Cleaning and Maintenance

Normal operating Sounds and Smells

Warrantee

Clearances

The ST900 electronic control system is designed to work within the

temperature range of 32°F to 176°F, with a humidity level that is non

condensing. This is to ensure safe operation of the electronic and

gas control system.

If the ﬁreplace is subjected to an environment with temperatures

very close to or exceeding these temperature limits (irrespective of if

the ﬁreplace is on or off at the time) the ﬁreplace may not start up

until the temperature returns back to within the operating range.

To remedy this the environmental temperature should be addressed

and the ﬁreplace control system given time to adjust accordingly.

The ﬁreplace should then function correctly.

Advanced Operation

Program Mode

Temperature

Time

Countdown Timer

Battery Status

Signal Indicator

Child Proof Thermostatic Mode

1 2

OFF

1 2

OFF

Fahrenheit

or Celsius

Changing the display from Celsius to Fahrenheit

Setting the Child Lock

Setting the Time

Press both and

buttons simultaneously

to change between

Celsius and Fahrenheit.

Note: choosing

Fahrenheit will change

the clock to a 12hr clock;

choosing Celsius will

change the clock to a

24hr clock.

ON: To turn on the Child

Lock, press and hold

and until is displayed.

The handset will no longer

respond to any button

presses except for the OFF

function.

OFF: To turn the child lock

off press and hold and

until is no longer

displayed.

1 2

OFF

1. Press the and buttons

simultaneously until the word

“day” ﬂashes.

2. Press the or button to

select a number; each

corresponding with a day of

the week (eg. Monday =

Tuesday = ).

3. Press the and buttons

simultaneously until the word

“hour” ﬂashes.

4. To change the hour press

the and buttons.

5. Press the and buttons

simultaneously until the word

“minutes” ﬂashes.

6. To change the minutes

press the and buttons.

7. To change the hour press

the and buttons.

Warning: If the pilot does not light or stay lit after several tries, call a qualiﬁed service

person to have the ﬁreplace serviced.

The ST900 remote handset allows the user to: turn the ﬁreplace ON and OFF, control

the ﬂame height in Manual mode, or control the room temperature in Thermostat

mode. The remote has a maximum range of 30 feet, and because the remote works

by radio frequency, it does not need to be aimed at the ST900 for it to operate.

Advanced Operation 2

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

Remote One-Button Startup (Default)

To Turn on the Fireplace

Press the button until a

series of blinking lines and

two short beeps conﬁrms

the ﬁreplace has turned on.

The remote automatically

goes into Manual mode

after the main burner is lit.

Setting the Remote to Two-Button Startup

To change from one button startup to two button

startup press and hold the button for 10

seconds immediately after installing the remote

batteries. The word ‘ON’, and ‘1' is displayed.

When the process is complete the ‘1' will change

to ‘2'.

Remote Two-Button Startup

Press the and button

simultaneously until a series

of blinking lines and two short

beeps conﬁrms the ﬁreplace

has turned on.

The remote automatically

goes into Manual mode after

the main burner is lit.

Setting the Remote to One-Button Startup

To change from two button startup to one button

startup press and hold the button for 10

seconds immediately after installing the remote

batteries. The word ‘ON’, and ‘2' is displayed.

When the process is complete the ‘2' will change

to ‘1'.

To Turn off the Fireplace

Press and hold the button

until the word ‘OFF’ is

displayed on the remote.

Flame Height Adjustment

High and Low Flame Settings

To increase the ﬂame height

press and hold the button

until the desired ﬂame height is

attained.

To decrease the ﬂame height or

set the ﬁreplace to pilot ﬂame,

press and hold the button until

the desired ﬂame height/setting

is attained.

Note: The remote handset backlight must be on for

the following to work.

To go to a set low ﬂame, double-

tap the button; will be

displayed on the remote screen.

To go to a set high ﬂame, double-

tap the button; will be

displayed on the remote screen.

Countdown Timer

Setting the Countdown Timer

1. Press and hold the button

until is displayed and the word

‘hour’ ﬂashes on the remote

screen.

2. To change the hour press the

or button.

3. To conﬁrm, press the

button. The word ‘minutes’ will

now be ﬂashing on screen.

4. To change the minute press

the or button.

5. To conﬁrm, press the button

or wait.

Turning off Countdown Timer

Press the button; will

disappear along with the

countdown time.

Note: At the end of

the countdown timer

period, the ﬁreplace

will turn off. The

countdown timer only

works in manual and

thermostatic modes.

The Maximum

countdown period is

9hrs and 50mins.

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

1 2

OFF

Advanced Operation

Thermostatic Mode

The desired room temperature

is set by the user and the

ﬁreplace adjusts its ﬂame

height automatically to achieve

this desired room temperature.

Operation Modes

There are 2 independent

programmable channels, each

can be conﬁgured to turn the

ﬁreplace on and off at speciﬁc

times at a set temperature.

Program Mode

Thermostatic Mode

To Turn on:

Press the button. Will be

displayed on the remote

screen and the desired room

temperature will be displayed

brieﬂy, followed by the current

room temperature.

To turn off:

1. Press the button.

2. Press the or button to

change to Manual mode or

press the button to enter

Program mode.

Setting:

1. Press and hold the button

until is displayed and the

temperature ﬂashes.

2. Press the or button to

set the temperature.

3. To conﬁrm press the

button or wait.

Program Mode

To turn on:

Press the button. , 1 or 2, ON or

OFF will be displayed.

To turn off:

1. Press the or or button to

enter Manual mode.

2. Press the button to enter

Thermostatic mode.

Note: The temperature set in Thermostatic mode is the

temperature used for the ON time in Program mode.

Default settings:

ON time (thermostatic) temperature: 21ºC

OFF time temperature: ‘ ‘ (pilot ﬂame)

Setting the Temperature:

1. Press and hold the button until

ﬂashes. ‘ON’ and the thermostatic

temperature is displayed.

2. To continue press the button or

wait. , ‘OFF’ is displayed and the

temperature ﬂashes.

3. Change the off temperature by

pressing the or button to increase

or decrease the temperature

respectively.

4. To conﬁrm, press the button.

Note: The on (Thermostatic) and off set temperatures are

the same for each day.

Setting the Day:

5. ﬂashes. Press the or

button to change between , ,

, , , , , .

6.To conﬁrm press the button.

1 2

OFF

1 2

OFF

Advanced Operation

Setting the ON time (Program 1)

7. , 1, ON is displayed, is

displayed brieﬂy and hours ﬂash.

8. Change the hour by pressing the

or button.

9. To conﬁrm, press the button.

, 1, ON is displayed, is

displayed brieﬂy and minutes ﬂash.

10. Change the hour by pressing

the or button.

11. To conﬁrm, press the button.

Setting the OFF time (Program 1)

7. , 1, OFF is displayed, is

displayed brieﬂy and hours ﬂash.

8. Change the hour by pressing the

or button.

9. To conﬁrm, press the button.

, 1, OFF is displayed, is

displayed brieﬂy and minutes ﬂash.

10. Change the hour by pressing

the or button.

11. To conﬁrm, press the button.

NOTE: Either continue to Program 2 and set the ON

and OFF times, or stop programming at this point and

Program 2 remains deactivated.

NOTE: Program 1 and 2 use the same ON

(Thermostatic) and OFF temperatures for , and

Daily timers ( , , , , , , ). Once a new ON

(Thermostatic) and/or OFF temperature has been set,

that temperature becomes the new default setting.

NOTE: If , or Daily timers are programmed for

Program 1 and/or Program 2 ON and OFF times, these

become the new default times. The batteries must be

removed to clear the Program 1 and 2 ON and OFF

times and temperatures.

or Daily timers ( , , , , , , ) selected

ŸSet the ON time and OFF time using the same

procedure as ‘ Selected’ (above)

Ÿ sets the ON and OFF time for both Saturday

and Sunday.

ŸDaily Timer: Unique ON and OFF times can be set

for a single day of the week, multiple days of the

week or for every day of the week.

ŸWait to ﬁnish setting.

Selected

5Advanced Operation

To Turn ON the Fireplace

ŸPress the button until two short beeps ON-OFF

conﬁrm the start sequence has begun.

Pilot Flame Mode (Standby)

ŸPress and hold the (small ﬂame/DOWN)

button to set appliance to Pilot Flame Mode.

To Turn OFF the Fireplace

ŸPress the button. ON-OFF

Flame Height Adjustment

ŸPress and hold (large ﬂame/UP) button to

increase the ﬂame height.

ŸPress and hold (small ﬂame/DOWN) button to

decrease the ﬂame height.

Installing the Batteries in the Receiver

NOTE: If batteries are installed in the receiver with

the transformer plugged in, the batteries will only be

consumed in the event of a loss of mains power.

1. Slide the cover off the receiver as shown in the

picture below.

FRONT

REAR

2.Place the 4 x AA Cell Batteries in the orientation

shown in the diagram below. We recommend using

good quality alkaline batteries.

On / Off

Flame Up

Flame Down

DOWN

ON-OFF

Touch Pad

This should only be used when the remote handset is

unavailable. To access this touch pad you must

remove the fascia (refer to page 8 of this manual). It is

located in the lower right corner on the base of the

ﬁreplace.

Automatic Turndown

The valve will turndown to pilot ﬂame if there is not

communication with the remote and the receiver for a 3

hour period. The ﬁre will continue to function normally

when communication is restore between the remote

and the receiver.

Automatic Shutdown

Countdown timer:

At the end of the countdown timer period, the ﬁreplace

will turn off.

Low Battery Receiver:

If the receiver has low batteries the ﬁreplace will

shutdown. This will not happen is the power supply is

interrupted.

FRONT FACE

Transformer Plug

Transformer plug location

The transformer plugs into the receiver as shown in the

diagram below.

Clearances

Cabinet Clearances

There must be a minimum of 4" from the sides of the fascia to any

protruding side walls or cabinetry.

Television Positioning Considerations

It is becoming common practice for consumers to mount flat screen TV's

above their gas fireplace.

Most TV manufacturers have specified in their instructions that the

TV should not be installed on, near or above a heat source. For this

reason TV location decisions rest solely with the householder and

the manufacturer / distributor will not be held liable for any adverse

affects on a TV located near to the ST900 fireplace that may be

caused by heat.

The drawings below are suggestions that may be used as a GUIDE

for those consumers who do decide to locate their TV above an

ST900 gas fire. These drawings show ways to reduce the amount of

warm air rising off the fireplace and onto the TV.

2”

20”

4”

2”

Mantle Mantle

Recessed TV

Flush TV with

small mantle Mantle above fire Protruding fire

20” 20”

20”

Autres manuels pour ST900

Table des matières

Autres manuels Escea Cheminée intérieure

Escea

Escea DS 1900 Instructions d'installation et d'entretien

Escea

Escea EF5000 - NZ Manuel utilisateur

Escea

Escea ST900 Manuel utilisateur

Escea

Escea ST900 Manuel utilisateur

Escea

Escea ST900 Manuel utilisateur

Escea

Escea DX1500 Manuel utilisateur

Escea

Escea AF700 Instructions d'installation et d'entretien

Escea

Escea DS Series Manuel utilisateur

Escea

Escea ST500 Manuel utilisateur

Escea

Escea AF series Manuel utilisateur

Escea

Escea IB850 Manuel utilisateur

Escea

Escea IB850 Manuel utilisateur

Escea

Escea DN1150 Corner 400 Manuel utilisateur

Escea

Escea DS Series Manuel utilisateur

Escea

Escea IB850 Manuel utilisateur

Escea

Escea DX1000 Instructions d'installation et d'entretien

Escea

Escea KS-Series Manuel utilisateur

Escea

Escea AF series Guide rapide

Escea

Escea EF5000 Manuel utilisateur

Escea

Escea DX1000 Manuel utilisateur

Escea

Escea EW5000 Instructions de montage

Escea

Escea IB850 Manuel utilisateur

Escea

Escea EF5000 - AUS Manuel utilisateur

Escea

Escea EF5000 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation