Escea ST500 Manuel utilisateur

ST500

GAS FIRE USER GUIDE

www.escea.net

630172_1 Manual_User_ST500_R-emotion_NZ

DO NOT PLACE ARTICLES OR FURNISHINGS ON OR AGAINST THIS

APPLIANCE.

DO NOT OPERATE THE FIRE IF THE GLASS HAS BEEN BROKEN,

DAMAGED OR IT IS NOT PROPERLY POSITIONED/HOOKED ONTO THE

FIRE

DO NOT OPERATE THE FIRE WITH THE FASCIAPANELS REMOVED.

THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE

MANUFACTURERS WRITTEN INSTRUCTIONS.

THE GLASS SURFACE ON THE FRONT OF THE FIREPLACE IS

CONSIDERED A WORKING SURFACE, AND AS SUCH IS HOT AND CARE

MUST BE TAKEN NOT TO TOUCH THIS SURFACE. IT IS RECOMMENDED A

SECONDARY GUARD IS FITTED IN PLACES WHERE THERE ARE YOUNG

CHILDREN ORAGED OR INFIRM PERSONS.

CURTAINS SHOULD NOT BE POSITIONED ABOVE THE FIREPLACE AND

ANY PROTRUDING LEDGES MUST NOT COME WITHIN THE MINIMUM

DISTANCES SPECIFIED IN SECTION 5.1 OF THE INSTALLATION MANUAL

SUPPLIED WITH THISAPPLIANCE.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR

INFIRM PERSONS UNLESS THEY HAVE BEEN ADEQUATELY

SUPERVISED BY A RESPONSIBLE PERSON TO ENSURE THAT THEY CAN

USE THE APPLIANCE SAFELY.

The data plate for this appliance, containing technical information and

specifications, can be found to the right of the control tray, near the

base of the fire. To access this, the fascia must be removed.

Any installation or service work carried out on this appliance must only

be done by a recognised and qualified gas fitter.

NZ LTD

17 Carnforth St, PO Box 5277

Dunedin, New Zealand

Escea recommends the ST500 is inspected and serviced by a

qualified Gas Fitter once every twelve (12) months.

E-mail: [email protected]

Web: www.escea.net

Phone: +64 03 478 8220

Basic Operation

Turning the ST500 on and off

Setting the Control Mode

Locking the Remote Control

Contents

Operation from the touch pad 4

Cleaning and Maintenance

Normal operating Sounds and Smells

Warranty Information

Clearances

The ST500 electronic control system is designed to work within the

temperature range of 0°C to 70°C, with a humidity level that is non

condensing. This is to ensure safe operation of the electronic and

gas control system.

If the fireplace is subjected to an environment with temperatures

very close to or exceeding these temperature limits (irrespective of if

the fireplace is on or off at the time) the fireplace may not start up

until the temperature returns back to within the operating range.

To remedy this the environmental temperature should be addressed

and the fireplace control system given time to adjust accordingly.

The fireplace should then function correctly.

Basic Operation

The ST500 remote control allows you to turn ON and OFF the fire, control the

flame height in the Manual mode, or control the room temperature in the

Thermostat mode. The remote has a maximum range of 10 meters, and

because the remote works by radio frequency, it does not need to be aimed at

the for it to operate.ST500

When first powered the remote starts at the OFF screen (it is possible that the

remote is locked in the OFF screen: to unlock it just press the button below

Unlock, and then OK).

Switching on the ST500

Switching on: Once the remote is unlocked, press On (left button) and OK

(middle button). A beep from the control unit will be heard, and the ignition

process starts (the pilot will start sparking and gas will start flowing to the pilot,

which should then be lit within a few seconds).

If the pilot flame fails to ignite, you must turn OFF the from the remote

and start the process of turning it ON again.

ST500

Basic Operation 2

To turn off the fire, push the OFF button, to shut down the gas flow to the fire

and switch it off. The OFF display will now appear in the display.

Switching off the ST500

There are three different modes for controlling the appliance:

Setting the control mode for the fireplace:

Automatic mode allows you to set a temperature, while in manual mode the

flame level may be set to HIGH, MEDIUM, LOW & PILOT. Program mode

offers automatic temperature control for specific times of the day.

In the initial screen when the remote is turned on, three options are available:

AUTO, MANUAL and MENU.

Auto and Manual are two of the three different modes for controlling the

appliance with the remote.

If Manual is pressed, Pilot appears as the selected

setting. In the bottom row, and appear,

indicating that the flame level can by changed by

just pressing the left or middle button. There are four

possible flame positions: Pilot flame, Low flame,

Medium flame and High flame. Pressing Back (right

button), returns to the initial screen. Note that a

Safety temperature can be previously set in the

configuration menu. This specifies the maximum

the maximum permitted room temperature. This

temperature can never be set higher than 40ºC (104

ºF).

↓↑

> Manual

> Automatic

> Program

Manual mode:

Basic Operation

If Auto is pressed in the initial screen, 25ºC (77 º F)

appears as the desired temperature in the selected

setting. In the bottom row, and appear,

indicating that we can change the desired

temperature value by just pressing the left or middle

button. In auto mode the appliance heats until this

temperature is reached. Limits are 0-37ºC (32-

99ºF).

Pressing Back (right button), returns to the initial

screen.

↓↑

Automatic mode:

Pressing Back (right button), returns to the initial screen.

In this mode the main burner can be switched on and off.

By default the program mode is not enabled. To enable program mode, enter

configuration mode by pressing and holding the OFF button for 40 seconds,

selecting “Programming” and selecting “yes” (For more information on

configuration mode see the installation manual, section 19.9).

There are two types of program mode: a Daily mode and a Weekly mode. In

the daily mode, every day uses the same program. In the weekly mode, every

day has its own program, so it is possible have a different program for each

day of the week.

In this mode the main burner can be switched on and off (pilot still burning).

(Menu Adjust Menu Change Program)Day programming menu: →→

Program mode:

There are 8 menus like this. One for Daily, and the others for each separate

day (Monday, Tuesday, Wednesday, Thursday, Friday, Saturday and

Sunday).

(Continued next page)

Basic Operation 4

The daily program screen consists of:

A: Selected (including “Daily”). The selected

day can be changed by pressing Change

(middle button).

B: Day schedule graphic. This bar displays

the program for the whole day by showing

the temperature setting for each hour of the

day. To access the day schedule graphic,

press (left button). To change the desired temperature, go to the hour you

want to change by pressing (left button) and then press change (middle

button).

There are 3 temperature settings (bars):

↓

→

Program mode (continued)

[Small bar] No temperature control (the appliance is in pilot

mode).

[Medium bar] The night temperature is set as the desired

temperature and the appliance will heat until this

temperature is reached. To adjust the night temperature

press “Menu Adjust menu Night” and set the desired

temperature.

[Large bar] The comfort temperature is set as the desired

temperature and the appliance will heat until this

temperature is reached. (High bar). To adjust the comfort

temperature pres Menu Adjust menu Comfort and set the

desired temperature.

→→

Finally, to launch the program mode, in the main menu, set Program to On,

and select the desired Program Type (Daily or weekly). When activated, the

screen will show which of the above temperature settings is currently active,

Off, Night, or Comfort. The pilot must remain lit in order for the program to

remain running.

Go into Menu Adjust menu Unit. Press middle button and then left button

for changing units.

→→

Changing the display from Celsius to Fahrenheit:

Off

Night Temp

Comfort Temp

Basic Operation

Operation from the Touch Pad

The touch pad is intended to be used for service/diagnostic purposes and to

operate the fire in the event that the remote handset becomes lost or inoperative.

If you remove the fascia you will find an electronic touch pad in the lower centre of

the fire. The touch pad features the basic operations of the fire: On, off, and

manual adjustment of the flame height.

DO NOT DROP THE REMOTE.

Dropping the remote may result in a cracked LCD screen or malfunctioning components.

The warranty does not cover damage to the remote sustained by dropping, however

replacement remote controls are available.

To Lock / Unlock the remote control buttons:

Go into Menu Lock. Press middle button and then left button for locking the

remote.

To unlock pres left button and then middle button.

→

To turn on the ST500, push the ON/OFF button on the touch pad. The system will

emit a beep and begin the ignition process, which can take about 20 seconds.

Once the start up process is complete, the pilot flame is lit. The ST500 is now in

the 'Manual' mode and ready to be used.

While the pilot is lit, press the 'Flame Up' or 'Flame Down' button to alter the flame

height. The LED will flash once and the unit will beep to confirm the flame height

has been adjusted. The ST500 has 4 flame positions: Pilot only, Low, Medium,

and High flame height.

If the 'Flame Up' button is pressed while the unit is in the 'high' flame position,

nothing will happen. Similarly, if 'Flame Down' is pressed while the unit is in the

'pilot' flame position, nothing will happen.

To shut down the gas flow to the ST500, press the On/Off button and the LED will

begin to blink and the unit will emit a beep.

Clearances

Cabinet Clearances

There must be a minimum of 100mm from the sides of the fascia to any

protruding side walls or cabinetry.

Television Positioning Considerations

It is becoming common practice for consumers to mount flat screen TV's

above their gas fireplace.

Most TV manufacturers have specified in their instructions that the TV should

not be installed on, near or above a heat source. For this reason TV location

decisions rest solely with the householder and Escea will not be held liable

for any adverse affects on a TV located near to an Escea fireplace that may be

caused by heat.

The drawings below are suggestions that may be used as a GUIDE for those

consumers who do decide to locate their TV above an gas fire. These

drawings show ways to reduce the amount of warm air rising off the fireplace

and onto the TV.

ST500

50 min

500 min 500 min

100 min

500 min

50 min

500 min

Mantle Mantle

Recessed TV

Flush TV with

small mantle Mantle above fire Protruding fire

Clearances

ST500 Mantle Clearances

If any part of the installation

(mantle, wall or cavity) is

constructed from

materials, the

diagram below shows the

maximum allowable size for

mantles or protruding surfaces

mounted above an

COMBUSTIBLE

ST500.

The material that the wall and mantle are made from will also affect the

operating temperature of the TV so it is the customers responsibility to

satisfy themselves that their TV mounting and mantle design will not

exceed the listed maximum operating temperature of their electronic goods.

If the entire installation (mantle,

wall and cavity) is constructed

from

materials, then the clearances to

mantles or protruding surfaces

mounted above an may be

as shown by the shaded area in

the diagram below

NON-COMBUSTIBLE

ST500

Replacing Batteries

When batteries are replaced in either the battery box (inside the

fireplace) or n the handset, the unit will require 1 minute afterwards to

regain connection.

Autres manuels pour ST500

Autres manuels Escea Cheminée intérieure

Escea

Escea EF5000 Manuel utilisateur

Escea

Escea DN1150 Corner 400 Manuel utilisateur

Escea

Escea ST900 Manuel utilisateur

Escea

Escea DS1400 Guide rapide

Escea

Escea EF5000 Manuel utilisateur

Escea

Escea NBS5525 Instructions de montage

Escea

Escea DF Series Instructions d'installation et d'entretien

Escea

Escea DX-Series Manuel utilisateur

Escea

Escea ST500 Manuel utilisateur

Escea

Escea NBS5525 Instructions de montage

Escea

Escea ST900 Manuel utilisateur

Escea

Escea IB850 Manuel utilisateur

Escea

Escea DS 1900 Instructions d'installation et d'entretien

Escea

Escea DX1000 Instructions d'installation et d'entretien

Escea

Escea IB850 Manuel utilisateur

Escea

Escea EF5000 Instructions d'installation et d'entretien

Escea

Escea EF5000 Manuel utilisateur

Escea

Escea EK950 Mode d’emploi

Escea

Escea EW5000 Manuel utilisateur

Escea

Escea DFS730 Manuel

Escea

Escea EK950 Manuel utilisateur

Escea

Escea KS1150 Peninsula 400 Guide rapide

Escea

Escea DX-Series Manuel utilisateur

Escea

Escea IB850 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation