ERNITEC MVID-04IR-E Manuel utilisateur

Dome Network Camera

MVID-04IR-E

Quick Start Guide

About this Manual

This Manual is applicable to MIVD-04IR-E Dome Network Camera.

The Manual includes instructions for using and managing the product.

Pictures, charts, images and all other information hereinafter are for

description and explanation only. The information contained in the

Please use this user manual under the guidance of professionals.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,

THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE

AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS

AND ERRORS, AND OUR COMPANY MAKES NO WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A

PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD

PARTY. IN NO EVENT WILL OUR COMPANY, ITS DIRECTORS,

OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR

ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT

DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS

OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF

DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF

THIS PRODUCT, EVEN IF OUR COMPANY HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE

USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.

OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES

FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER

DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,

VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL

SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK

ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING

THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE

CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT

BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH

ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND

THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modication not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

FCC compliance: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to ra-

dio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer-

ence that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories

too are marked with "CE" and comply therefore with the

applicable harmonized European standards listed under the

the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/

EU.

2012/19/EU (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste in

the European Union. For proper recycling, return this product

to your local supplier upon the purchase of equivalent new

equipment, or dispose of it at designated collection points.

For more information see: www.recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery

directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European

Union. See the product documentation for specific battery

information. The battery is marked with this symbol, which

may include lettering to indicate cadmium (Cd), lead (Pb),

or mercury (Hg). For proper recycling, return the battery to

your supplier or to a designated collection point. For more

information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards require-

ments.

Safety Instruction

These instructions are intended to ensure that the user can use the

product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws, electrical

safety regulations, and re prevention regulations.

Transportation

Keep the device in original or similar packaging while transporting it.

Power Supply

The input voltage should conform to IEC60950-1 standard: SELV

(Safety Extra Low Voltage) and the Limited Power Source. Refer to

the appropriate documentation for detailed information.

The standard power supply is 12 VDC, or PoE (802.3af), please make

sure your power supply matches with your camera.

DO NOT connect multiple devices to one power adapter, to avoid

over-heating or re hazards caused by overload.

Make sure the plug is properly connected to the power socket.

System Security

The installer and user are responsible for password and security

conguration and its settings.

Battery

Improper use or replacement of the battery may result in explosion

hazard. Replace with the same or equivalent type only. Dispose of

used batteries in conformance with the local codes.

Maintenance

If the product does not work properly, please contact your dealer or

the nearest service center. We shall not assume any responsibility for

problems caused by unauthorized repair or maintenance.

A few device components (e.g., electrolytic capacitor) require regular

replacement. The average lifespan varies, so periodic checking is

recommended. Contact your dealer for details.

Cleaning

Please use a soft and dry cloth when clean inside and outside

surfaces of the product cover. Do not use alkaline detergents.

Using Environment

When any laser equipment is in use, make sure that the device lens is

not exposed to the laser beam, or it may burn out.

Do not expose the device to high electromagnetic radiation or dusty

environments.

For indoor-only device, place it in a dry and well-ventilated

environment.

Do not aim the lens at the sun or any other bright light.

Make sure the running environment meets the requirement of the

device. The operating temperature shall be -30 °C to 60 °C (-22 °F

to 140 °F), and the operating humidity shall be 95% or less (non-

condensing).

Do not place the camera in extremely hot, cold, dusty or damp

locations, and do not expose it to high electromagnetic radiation.

IR Reection Prevention

Dust or grease on the dome cover will cause IR reflection. Please

do not remove the dome cover lm until the installation is nished. If

there is dust or grease on the dome cover, clean the dome cover with

clean soft cloth and isopropyl alcohol.

Make sure that there is no reective surface too close to the camera

lens. The IR light from the camera may reflect back into the lens

causing reection.

The foam ring around the lens must be seated ush against the inner

surface of the bubble to isolate the lens from the IR LEDS. Fasten the

dome cover to camera body so that the foam ring and the dome cover

are attached seamlessly.

Emergency

If smoke, odor, or noise arises from the device, immediately turn off

the power, unplug the power cable, and contact the service center.

Time Synchronization

Set up camera time manually for the rst time access if the local time

is not synchronized with that of the network. Visit the camera via Web

browse/client software and go to time settings interface.

Installation

Make sure the device is firmly secured to any wall or ceiling

mountings.

Be sure that there is enough space to install the camera and

accessories.

Make sure that the device in the package is in good condition and all

the assembly parts are included.

Make sure that the wall is strong enough to withstand at least 4 times

the weight of the camera and the mount.

Make sure that the power has been disconnected before you wire,

install, or disassemble the device.

Symbols and Marks

Notice

Warning

Forbidden

Correct

Incorrect

Turn to page A and continue.

i. Not necessarily included accessory.

ii. Variable accessory amount.

iii. Skip this step if not required.

MicroSD card

Grounding

Disposal

Purchase separately

1x 1x

T10

T20

microSD

1.1

1.1 1.2

T10

1.2

Table des matières

Autres manuels ERNITEC Caméra de sécurité

ERNITEC

ERNITEC Mercury SX32 Series Manuel utilisateur

ERNITEC

ERNITEC SX Series Manuel utilisateur

ERNITEC

ERNITEC DS-2CD6924G0-IHS Manuel utilisateur

ERNITEC

ERNITEC Orion Manuel utilisateur

ERNITEC

ERNITEC Mercury SX4 series Manuel utilisateur

ERNITEC

ERNITEC MicroView MVIC-O4IR-E Manuel utilisateur

ERNITEC

ERNITEC MicroView MVIB-04IR-E Manuel utilisateur

ERNITEC

ERNITEC Orion/2 Mode d’emploi

ERNITEC

ERNITEC Orion DX 822IR Manuel utilisateur

ERNITEC

ERNITEC Orion/2 Manuel utilisateur

ERNITEC

ERNITEC Orion DX 3 Manuel utilisateur

ERNITEC

ERNITEC MicroView MVIB-01IR-E Manuel utilisateur

ERNITEC

ERNITEC Performance Series Manuel utilisateur

ERNITEC

ERNITEC Hawk SX Manuel utilisateur

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manuel utilisateur

ERNITEC

ERNITEC Corona IP-452 IR Manuel utilisateur

ERNITEC

ERNITEC MicroView MVID-03IR-E Manuel utilisateur

ERNITEC

ERNITEC DS-2CD6986F-H Manuel utilisateur

ERNITEC

ERNITEC MERCURY SX 5TH GENERATION Manuel utilisateur

ERNITEC

ERNITEC EVA 101 Manuel utilisateur

ERNITEC

ERNITEC SX Manuel utilisateur

ERNITEC

ERNITEC MicroView MVIB-01IR-E Manuel utilisateur

ERNITEC

ERNITEC MicroView MVCLOUD-101 Manuel utilisateur

ERNITEC

ERNITEC ASTRAL Instructions de montage

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur