Ergotron Neo-Flex Manuel utilisateur

1 of 19

888-24-075-W-01 rev. M • 01/19

www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]

English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语

Neo-Flex™

WideView Workspace

Användarhandbok

Svenska

För den senaste Installationshandboken se: www.ergotron.com

2 of 19

888-24-075-W-01 rev. M • 01/19

WARNING

DO NOT load Cart below minimum or above

maximum weight capacities. DO NOT mount a

display larger than the recommended size.

Failure to comply with warning may result in

Cart instability leading to equipment damage or

personal injury.

Min. 11 lbs (5 kg)

Max. 46 lbs (20.9 kg)

Min. 14 lbs (6.35 kg)

Max. 49 lbs (22.2 kg)

WARNING

Impact Hazard!

Moving Parts can Crush and Cut.

Minimize Lift Tension BEFORE

Removing Mounted Equipment.

To Minimize Lift Tension

1. Lower worksurface to lowest position.

2. Turn adjustment nut at top of riser

counterclockwise until it stops (may require

40-60 turns to minimize lift tension).

3. After removing or adding equipment adjust

lift tension to compensate for weight

of new load.

Failure to heed this warning may result in

serious personal injury or property damage!

14mm

9/16”



WARNING

A primary mechanism within the Cart

is under tension and can be

hazardous to people exposed to it

under certain conditions.

DO NOT open the Cart tower or base.

DO NOT attempt to service the Cart.

DO NOT remove safety guards or

labels designed to protect or inform

of possible hazards.

Only Ergotron-approved installers

may service or otherwise modify

Cart. Failure to heed this Warning

may result in serious Personal Injury

and Damage both to the cart and

equipment.

STORED ENERGY HAZARD!

DO NOT OPEN TOWER OR BASE.

DO NO REMOVE SAFETY GUARD.

240-027-00

TIPPING HAZARD!

DO NOT allow children to climb on Cart.

DO NOT route electric cords or equipment

cables within reach of children.

LOCK CASTERS when Cart is stationary.

DO NOT move Cart with Display in highest

position.

DO NOT move Cart over cords or uneven, dirty,

soft or sloping surfaces.

DO NOT move Cart by pushing on Display.

Failure to comply with this warning may result

in Cart instability leading to equipment

damage or personal injury.

WARNING

TO MOVE CART

1. Push Display down to lowest position.

2. Disconnect power cord and secure to Cart.

Unlock casters; point casters in direction of travel.

4. Use rear handle to push Cart.

SafetySäkerhet

3 of 19

888-24-075-W-01 rev. M • 01/19

12"-18"

(305-457 mm)

3"- 8.5"

(76-216 mm)

<40 lbs. ( 18.1 kg)

20"

(50.8 cm)

20"

(50.8 cm)

16 - 30 lbs

(7.3 - 13.6 kg)

20˚*

10˚*

90˚

*±5˚

Stand

Sit

Funktioner och speciﬁkationer

VARNING: ÖVERSKRID INTE

MAXVIKTKAPACITETEN. DU

KAN ORSAKA ALLVARLIG PER-

SON ELLER EGENDOMSSKADA

CPU Holder

Stand

Sit

Viktigt! Efter avslutad installation måste du justera produkten. Se till att all utrustning är installerad

korrekt innan du påbörjar justeringen. Du ska lätt kunna ﬂytta produkten över hela rörelseområdet och

den ska stanna i den position du lämnar den. Om det är för lätt eller trögt att ändra positioner eller om

produkten inte stannar i avsedd position, följ justeringsinstruktionerna för optimal positionsrörlighet. Det

kan ta mer än en justering för att nå önskat beteernde beroende på produkt och justering. Om du lägger

till eller tar bort utrustning bör du jutera produkten för den nya viktbelastningen. På så sätt bibehåller du

en säker och behaglig arbetssitation.

4 of 19

888-24-075-W-01 rev. M • 01/19

AB C D E F

14mm (9/16")

19mm

(3/4")

>9" (229 mm)

8mm

(5/16")

M4 x 12mm

3mm

1x 1x

2x 4x

M5 x 18mm

1x 2x

1x 2x 2x

M5 x 10mm

M5 x 8mm

1x 4x 1x

M3 x 6mm

M6 x 14mm

M6x33mm

4x 4x 4x 4x

M5 x 12mm M5 x 20mm

M5 x 7mm M6 x 12mm

CPU Holder

5-sided Security Wrench

Security Screw

Mounting Holes

M8M5 Converter

Komponenter

Verktyg som behövs

CPU Holder

Vite di sicurezza

5-sided Security Wrench

Mounting Holes

M8M5 konverterare

5 of 19

888-24-075-W-01 rev. M • 01/19

3mm

efg

1180˚

19mm

(3/4")

5-sided Security Wrench5-sided Security Wrench

CPU Holder NOTE: If you are not attaching a CPU to your

cart, skip step 2 and proceed to step 3.

6 of 19

888-24-075-W-01 rev. M • 01/19

3mm

5-sided Security Wrench

Caution: Do Not over tighten fasteners.

NOTE: Position at bottom of tower.

Do not tighten at this time.

Tipping Hazzard: Position bracket so that CPU

attaches as low as possible on the tower.

7 of 19

888-24-075-W-01 rev. M • 01/19

M5 x 18mm

5-sided Security Wrench

Vite di sicurezza

8 of 19

888-24-075-W-01 rev. M • 01/19

Mounting HolesMounting Holes

9 of 19

888-24-075-W-01 rev. M • 01/19

4abcd

M5 x 10mm

iiiii

10 of 19

888-24-075-W-01 rev. M • 01/19

5abc

egf

>9" (229 mm)

M6x33mm

Autres manuels pour Neo-Flex

Table des matières

Langues :

Autres manuels Ergotron Support et étagère

Ergotron

Ergotron LX Desk Mount LCD Arm Manuel utilisateur

Ergotron

Ergotron DS100 Series Manuel utilisateur

Ergotron

Ergotron 97 815 Manuel utilisateur

Ergotron

Ergotron StyleView Sit Stand Combo Arm Manuel utilisateur

Ergotron

Ergotron Neo-Flex Manuel utilisateur

Ergotron

Ergotron Height Adjustable Systems HD Series Arms Dimensions

Ergotron

Ergotron LX Manuel utilisateur

Ergotron

Ergotron LX Dual Side-by-Side Arm Manuel utilisateur

Ergotron

Ergotron StyleView 5 Manuel utilisateur

Ergotron

Ergotron DS100 Series Manuel utilisateur

Ergotron

Ergotron FX30 Dimensions

Ergotron

Ergotron DS100 Series Manuel utilisateur

Ergotron

Ergotron LX Desk Mount LCD Arm Manuel utilisateur

Ergotron

Ergotron Neo-Flex Series Manuel utilisateur

Ergotron

Ergotron 97-585 Manuel utilisateur

Ergotron

Ergotron StyleView Guide de dépannage

Ergotron

Ergotron 888-33-332 Manuel utilisateur

Ergotron

Ergotron TeachWell LCD Manuel utilisateur

Ergotron

Ergotron StyleView Manuel utilisateur

Ergotron

Ergotron Neo-Flex Manuel utilisateur

Ergotron

Ergotron MXV Manuel utilisateur

Ergotron

Ergotron LX Desk Dual Direct Arm Manuel utilisateur

Ergotron

Ergotron StyleView SV32 Manuel utilisateur

Ergotron

Ergotron LX Desk Mount LCD Arm Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur