EPOX V370A Manuel utilisateur

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without

notice.

Manual Revision 2.0

DEC 30, 1998

V370A

ISA/PCI AGP Motherboard with

Onboard PCI IDE and Super

Multi-I/O

FeaturesV370A

Page 2

FEATURES

V370A Features:

•V370A is based on the Mendocino Processor operating at 300 ~

433MHz on PGA370. The board is configured by an ESDJ to match

your CPU clock speed.

•Designed with VIA APOLLO PRO AGPset.

•Supports up to 768 Mega of DRAM (minimum of 16 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at

66MHz or 100MHz (please see Section 3-2).

•V370A will support Error Checking and Correcting (ECC) when using

paritys DRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

•Supports (2) 16 bit ISA slots, (4) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The V370A supports (2)

PCI Bus Master slots and a jumperless PCI INT# control scheme which

reduces configuration confusion when plugging in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

•Designed with Winbond W83877TF Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

•Includes a PS/2 mouse connector.

•Allows use of a PS/2 keyboard.

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com

please visit our Technical Support section for the latest updates)

FeaturesV370A

Page 3

•V370A utilizes a Lithium battery which provides environmental protection

and longer battery life.

•Supports the Universal Serial Bus (USB) connector. The onboard VT82C596

chip provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely.

•Resume by Alarm - Allows your system to turn on at a preselected time.

•Supports CPU Hardware sleep and SMM (System Management Mode).

•Supports Keyboard power ON function (KBPO).

•Supports USDM software to offer motherboard various status.

•Supports the CPU, PWR and Chassis fan Auto stop in sleep mode.

•Built-in WOL (Wake On LAN)Connector.

• Built-in SB-LINK Header for Creative Blaster®AWE64D PCI Bus Sound

Card.

InstallationV370A

Page 4

Figure 1

V370A Detailed Layout

AGP SLOT

ISA Slot #1

ISA Slot #2

Battery

ATX Power Input

Winbond

83877

I/Oset

USB 1

(Top)

Mouse

(Top)

USB 0

(Bottom)

Keyboard

(Bottom)

IDE2

Secondary IDE

IDE1

FDD1

J7:WOL

Flash Memory

for BIOS

PCI Slot #1

PCI Slot #2

PCI Slot #3

PCI Slot #4

COM 1COM 2COM 2

USB

PS/2

Parallel Port

SB_Link

CHASSIS FAN

DIMM 2

DIMM 1

Bank 1

DIMM 3 Bank 2

Bank 0

POWER

FAN

CPU FAN

J4 J5

JP1

RESET

SPK

KEYLOCK

POWER_ON

IR CONN.

JP3

103MHz

100MHz

83MHz

75MHz

66MHz

5.5X

4.5X

2 1

26 25

112MHz

6.5X

AUTO

JP4

JP5

InstallationV370A

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure Jumpers to match your hardware

Install memory chips

Device Connector

Configure Jumpers

We design this motherboard with an ESDJ to make your installation fast and easier.

The following will describe all of the ESDJ that you are required to set before moving

on to step 2.

Note: The ESDJ as depicted as shown (Figure 1) in their correct physical

orientation.

JP1 Clear CMOS

1-2 : Run Mode (default)

2-3 : Clear CMOS

JP4 Keyboard Power on Selection

1-2 : Disabled (default)

2-3 : Enabled

InstallationV370A

Page 6

System Memory Configuration

Memory Layout

The V370A supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized

DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

120MHz (8ns) bus speed.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using both

SDRAM and EDO memory.

DIMM 1

DIMM 2

Bank 0

Bank 1 -Synchronous

-EDO

DIMM 3

Bank 2

JP5 SDRAM CLOCK Selection

1-2 : SDRAM=CPU (Default)

2-3 : SDRAM=AGP (2/3 CPU CLOCK)

InstallationV370A

Page 7

* SDRAM only supports 8, 16, 32, 64, 128, 256MB DIMM modules.

Table 1

yromeMlatoT 1MMID )0knaB( 2MMID )1knaB( 3MMID )2knaB(

BM652= mumixaM

*MARDS/ODE ,BM23,BM61,BM8 BM652,BM821,BM46 1X

enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

enoN

BM867=

mumixaM

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

*MARDS/ODE

,BM23,BM61,BM8

BM652,BM821,BM46

InstallationV370A

Page 8

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connections

(figure 12).

J2:Keylock, Speaker, Reset

J3:IR Conn. TB-LED, HDD-LED, POWER_ON

J4:CPU Fan Power

• A plug-in for the CPU Fan Power

J5:POWER Supply FAN POWER

• A plug-in for Power Supply Fan Power

J6:Chassis Fan Power

• A Plug-in for the chassis Fan Power

J7:WOL (Wake on LAN)Connector

J8: SB_Link Header

IDE1: Primary IDE

IDE2: Secondary IDE

FDD1: FloppyController

Figure 12

USB 1

(Top)

USB 0

(Bottom)

PS/2 Mouse

(Top)

PS/2 Keyboard

(Bottom)

Parallel Port

(Top)

Com1 Com2

(Bottom Left) (Bottom Right)

12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345

InstallationV370A

Page 9

Power On/Off - This is connected to the power button on the case.

Using the Soft-Off by Pwr-BTTN feature, you can choose either

Instant Off (turns system off immediately), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off). When

the system is in 4 sec delay mode, V370A has added a special

feature to make the system go into suspend mode when the button is

pressed momentarily.

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Turbo LED indicator - LED ON when higher speed is selected

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is

activate

KeyLock - Keyboard lock switch & Power LED connector

1. Power LED(+) 4. Keylock

2. N/C 5. GND

3. GND

Table des matières

Autres manuels EPOX Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur