E+E Elektronik EE210 Manuel utilisateur

The EE210 transmitter, available for wall or duct mounting, is designed for the highly accurate measurement of humidity and tempera-

ture in demanding climate control applications. The EE210 incorporates the E+E humidity and temperature sensor HCT01.

For use in special applications do not hesitate to contact E+E Elektronik or a local distributor.

GENERAL

• For accurate measurement it is essential that the temperature of the sensing probe and mainly of the sensing head is same as

the temperature of the air to measure. Avoid mounting the transmitter in a way which creates temperature gradients along the

probe.

• The transmitter and mainly the sensing head shall not be exposed to extreme mechanical stress.

• The transmitter must be operated with the filter cap on at all times.Do not touch the sensors inside the sensing head.

• While replacing the filter cap (because of pollution for instance) against an original spare one please take very good care to

not touch the sensors.

CAUTION

USER‘S GUIDE

EE210 - Humidity and Temperature Transmitter for

demanding Climate Control Applications

EE210-HT6*

20...30VDC RL<500 Ohm

11...30VDC RL<50 Ohm

Output: 4...20mA

Output: 0...5V

0...10V

Output:

Modbus RTU or

BACnet MS/TP

15...35VDC

24VAC ±20%

15...35VDC

24VAC ±20%

EE210-HT3

EE210-HTx3

CONNECTION DIAGRAM

ONLY FOR REMOTE PROBE!

*Important:

In the case of EE210-HT6 (4...20mA, two-wire version) the display

operates only if both outputs are connected.

Bus termination resistor 120 Ω (jumper)

Green LED - information to normal operation mode:

on = everything OK

ﬂ ashing = the main board does not recognize the

measurement electronics inside the sensing probe

off = no power supply or main board failure

Blue LED - information during setup with the optional

E+E Con guration Kit:

on = E+E Product Con guration Adapter (EE-PCA) is

powered, no communication in progess

ﬂ ashing = EE-PCA powered, communication in progress

off = EE-PCA not connected to the EE210

LED INDICATION

CONNECTION DIAGRAM

EE210P (type C)

The EE210P remote probe for EE210-HT6xPC (4 … 20mA, 2-wire) and HTx3xPC (RS485 interface) shall be ordered and it is supplied

as separate item. EE210P is to be connected to the EE210 by the user.

• Install first the cable gland onto the EE210 enclosure.

• Before connecting the probe, disconnect the EE210 power supply.

• Insert the EE210P cable through the cable gland and connect it to the screw terminals according to the connection diagram below.

Please note:

EE210P is an intelligent probe with digital output and as such it is interchangeable. In case the probe or its cable gets destroyed or if a

longer cable is needed, please order a replacement probe according to EE210 data sheet. The replacement probe shall be installed as

described above.

Important:

Make sure that the cable glands are closed tightly for both EE210P probe cable and for the power supply and outputs cable. This is

necessary for assuring the protection class (IP class) of the enclosure according to EE210 speci cation, as well as for stress relief at the

screw terminals on the EE210 board.

Factory Setup:

The display shows the two parameters selected for output 1 and output 2 (accor-

ding to ordering code). For digital output versions the display shows RH and T.

User Setup:

The user can change the display layout to 1, 2 or 3 lines and select the

parameters to be displayed by using EE-PCS Product Configuration Software

(free download from www.epluse.com/configurator) and the optional EE-PCA

Product Configuration Adapter (not included in the scope of supply).

Important:

In the case of EE210-HT6 (4...20mA, two-wire version) the display operates only

if both outputs are connected.

DISPLAY

DIGITAL SETTINGS

Protocol setting:

Address, baudrate, parity and stop bits can be set via:

1. Congurator software (available on www.epluse.com/EE210)

2. Modbus protocol (please see Application Note Modbus (available on www.epluse.com/EE210)

FLOAT (read register):

address

Communication

address

Parameter

name

30026 0x19 temperature [°C], [°F]

30028 0x1B relative humidity [%]

30030 0x1D water vapour partial pressure [mbar], [psi]

30032 0x1F dew point temperature [°C], [°F]

30036 0x23 absolute humidity [g/m³], [g/ft³]

30038 0x25 mixing ratio [g/kg], [gr/lb]

30040 0x27 specic enthalpy [kJ/kg], [BTU/lb]

30042 0x29 frost point temperature [°C], [°F]

The measured values are saved as a 32Bit float value from 0x19 to 0x1F and from 0x23 to 0x29. Additionally the measured values

are available as 16Bit signed integer from 0x12C to 0x12F and from 0x131 to 0x134.

The factory setting for the Slave-ID (Modbus address) is 242 as an integer 16Bit value. This ID can be changed by the user in the

The serial number as ASCII-code is located at register address 30001-30008 (16Bit per address).

The Firmware version is located at register address 30009 (Bit 15...8 = major release; Bit 7...0 = minor release).

The choice of measurement units (metric or not metric) must be done in the ordering guide, see EE210 data sheet.

Switching from metric to non metric or vice versa by using the EE-PCS is not possible.

BACnet PICS are abvailable for download at www.epluse.com/EE210

INTEGER (read register):*

address

Communication

address

Parameter

name

30301 0x12C temperature [°C], [°F]

30302 0x12D relative humidity [%]

30303 0x12E water vapour partial pressure [mbar], [psi]

30304 0x12F dew point temperature [°C], [°F]

30306 0x131 absolute humidity [g/m³], [g/ft³]

30307 0x132 mixing ratio [g/kg], [gr/lb]

30308 0x133 specic enthalpy [kJ/kg], [BTU/lb]

30309 0x134 frost point temperature [°C], [°F]

* Values are stored with a scaling of 1:100 (e.g.: 2550 is equivalent to 25.5°C)

INTEGER (write register):*

address

Communication

address

Parameter

name

60001 0x00 Slave-ID (modbus addresse)

60002 0x01 Modbus protocol settings*

*For Modbus protocol setting please see Application Note Modbus

(www.epluse.com/EE210)

INFO (read register):

address

Communication

address

Parameter

name

30001 0x00 Serial number (as ASCII)

30009 0x08 Firmware version

BACnet Setup

Modbus Setup

Address Switch

Slave address setting via EE-PCS Product Conguration Software:

All switches at position 0 → address has to be set via conguration software

(factory setting 242).

Example: Slave address is set via conguration software.

Slave address setting via Dip-Switch:

Setting the Dip-Switch to any other address than 0 overwrites the slave address set

via conguration software.

Example: Slave address set to 11 (=00001011 binary).

TECHNICAL DATA

∆ °C

°C

∆ °C

°C

(Modification rights reserved)

Measured Values

Relative Humidity (RH)

Sensor E+E Sensor HCT01-00D

Working range 0...100% RH

RH accuracy (incl. hysteresis, non-linearity and repeatability)

Wall & duct version:

-15...40°C (5...104°F) ≤90% RH ±(1.3 + 0.003*measured value) % RH

-15...40°C (5...104°F) >90% RH ± 2.3% RH

-40...60°C (0...140°F) ±(1.5 + 0.015*measured value) % RH

Remote probe version

at 20°C (68°F) ±2.5% RH

Temperature (T)

Sensor Pt1000 (tolerance class B, DIN EN 60751) integrated in HCT01

T-accuracy wall & duct remote probe

Outputs

Analog output 0-5 V / 0-10 V -1 mA < IL< 1 mA

(RH: 0...100%; T: see ordering guide) 4-20 mA (two-wire) RL≤ 500 Ohm

Digital output RS485 (BACnet MS/TP or Modbus RTU), max. 32 EE210 in one bus

General

Power supply

for 0-5 V / 0-10 V / RS485 15 - 35V DC1) or 24V AC ±20%

for 4-20 mA 10V + RL x 20 mA < V+ < 30V DC

Current consumption

Voltage output DC supply typ. 3.3mA; with display typ. 3.6mA

AC supply typ. 34mA; with display typ. 37mA

Current output DC supply max. 40mA

Digital interface DC supply typ. 5mA; with display typ. 19mA

AC supply typ. 52mA; with display typ. 118mA

Display 1, 2 or 3 lines, user configurable

Connection Screw terminals, max. 1.5 mm2

Housing material Polycarbonate, UL94V-0 (with Display UL94HB) approved

Protection class IP65 / NEMA 4

Cable gland M16 x 1.5

Probe cable (type C) PVC, Ø 4.3mm, 4 x 0.25 mm2, Length: 1.5 or 3m (4.9 or 9.8ft)

Sensor protection E+E Coating

Electromagnetic compatibility EN61326-1 EN61326-2-3

Industrial Environment

Temperature ranges Operating: -40...60°C (-40...140°F) (-40...80°C for remote probe EE210P)

Storage: -40...60°C

(-40...140°F)

Temperature ranges with display Operating: -20...50°C (-4...122°F) (-40...80°C for remote probe EE210P)

Storage: -20...60°C

(-4...140°F)

1 USA & Canada: class 2 supply required, max. supply voltage 30V

FOR CONDUIT

INSTALLATION

CABLE GLAND M16x1.5

~55mm

~2.16“

Ø 12mm

Ø 0.47“

60 ±0.3mm

2.36 ±0.11“

Ø > 16mm

Ø > 0.63“

6mm

0.24“

90 ±0.3mm

3.54 ±0.11“

Ø > 13mm

Ø > 0.51“

~205mm

~8.07“

101mm

3.98“

19mm

0.75“

90 ±0.3mm

3.54 ±0.11“

46mm

1.81“

5mm

0.2“

80.6mm

3.17“

34mm

1.34“

106mm

4.17“

GASKET

Recommended mounting screws:

ST4.2x50 DIN7981C

Type C

Type A Type B

EE210P

DIMENSIONS / MOUNTING

SCOPE OF SUPPLY

EE210 WALL MOUNT (TYP A):

• EE210 Transmitter according Ordering Guide

• 1 x Cable gland

• Mounting kit

• Inspection certificate according to DIN EN10204 - 3.1

EE210 DUCT MOUNT (TYP B):

• EE210 Transmitter according Ordering Guide

• 1 x Cable gland

• Mounting flange

• Mounting kit

• Inspection certificate according to DIN EN10204 - 3.1

EE210 WITH REMOTE PROBE (TYP C):

• EE210 Transmitter according Ordering Guide

• 2 x Cable gland

• Mounting kit

• Inspection certificate according to DIN EN10204 - 3.1

EE210-P REMOTE PROBE:

• EE210-P according Ordering Guide

• Mounting flange

• Inspection certificate according to DIN EN10204 - 3.1

• !! EE210-P is not included in the Scope of Supply of the EE210 Type C !!

ADDITIONALLY FOR ALL EE210 WITH RS485 INTERFACE:

• 1 x Cable gland

• Quick Guide – EE210 Modbus Setup

INFORMATIONEN +43 7235 605 0 / [email protected]

Langwiesen 7 • A-4209 Engerwitzdorf

Tel: +43 7235 605-0 • Fax: +43 7235 605-8

[email protected] • www.epluse.com

LG Linz Fn 165761 t • UID-Nr. ATU44043101

Place of Jurisdiction: A-4020 Linz • DVR0962759

ACCESSORIES

Position 1:

- configuration adapter (incl. USB cable for PC) EE-PCA

Position 2:

- cable for configuration adapter HA011062

Position 3:

- configuration software: EE-PCS

free of charge; download: www.epluse.com/EE210

Position 4 - optional:

- power supply for EE210 V03

Configuration kit: The con guration kit allows user setup for the output scaling and for the interface parameters, as well as humidity

and temperature adjustment of the sensor.

BA_EE210_e // v1.3 // Modification rights reserved

USA

FCC notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CANADIAN

ICES-003 Issue 5:

CAN ICES-3 B / NMB-3 B

MAINTENANCE

When employed in dusty, polluted environment:

• The filter cap shall be replaced once in a while with an E+E original one. A polluted filter cap causes longer response time of the

device.

• If needed, the sensing head can be cleaned. For this remove first very carefully the filter cap. Take care not to hit the sensing

head. Shake slowly the sensing head for one minute in a solution of 50% isopropyl alcohol with 50% distilled water. Then the sen-

sing head shall be rinsed with cold tap water and let dry freely. Do not touch or rub the sensing head! After cleaning the sensors

install carefully a new E+E original filter cap.

The EE210 transmitter is ready to use and does not require any con guration by the user. The factory setup of EE210 corresponds to the

type number ordered. (Ordering guide please see data sheet at www.epluse.com/EE210.)

If needed, the user can change the factory setup by using the optional E+E Product Configuration Adapter (EE-PCA) and the E+E

Product Configuration Software (EE-PCS).

One can assign other physical quantities to the analogue outputs, change the scaling of the outputs and perform one or two point ad-

justment for humidity and temperature.

For con guration with EE-PCA and EE-PCS both 4-20 mA two-wire outputs must be connected.

For product data sheets EE-PCS and EE-PCA please see www.epluse.com.

The E+E Product Configuration Software (EE-PCS) is free and can be downloaded from www.epluse.com/configurator.

SETUP AND ADJUSTMENT



HA011062

HA011050

V03 (optional)

Autres manuels pour EE210

Table des matières

Autres manuels E+E Elektronik Émetteur

E+E Elektronik

E+E Elektronik EE04 Series Instructions d'utilisation

E+E Elektronik

E+E Elektronik EE06 Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE210 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE65 Series Instructions d'utilisation

E+E Elektronik

E+E Elektronik EE210 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE36 Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE22 Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE360 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE355 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE375 Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE29 Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE360 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE150 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE23 series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE310 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE040 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE310 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE650 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE23 series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE310 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE31 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE650 Manuel utilisateur

E+E Elektronik

E+E Elektronik EE300E Series Manuel utilisateur

E+E Elektronik

E+E Elektronik EE061 Series Manuel d'instructions

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur