Endress+Hauser iTEMP TMT86 Caractéristiques techniques
Products Solutions Services
Brief Operating Instructions
iTEMP TMT86
Dual-input temperature transmitter
PROFINET® protocol
These Instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
For detailed information, refer to the Operating Instructions
and other documentation.
Available for all device versions via:
• Internet: www.endress.com/deviceviewer
• Smart phone/Tablet: Endress+Hauser Operations App
KA01529T/09/EN/01.21-00
71562442
2021-11-30
iTEMP TMT86
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
iTEMP TMT86 Table of contents
Endress+Hauser 3
Table of contents
1 About this document .............................................................. 3
1.1 Symbols used ......................................................................... 3
1.2 Tool symbols ..........................................................................4
1.3 Registered trademarks .................................................................. 4
2 Safety instructions ................................................................ 4
2.1 Requirements for personnel .............................................................. 4
2.2 Intended use .......................................................................... 5
2.3 Workplace safety ...................................................................... 5
2.4 Operational safety ......................................................................5
2.5 Product safety ......................................................................... 5
2.6 IT security ............................................................................ 5
3 Incoming acceptance and product identification ................................... 6
3.1 Incoming acceptance .................................................................... 6
3.2 Product identification ................................................................... 6
3.3 Certificates and approvals ................................................................ 7
3.4 Storage and transport ................................................................... 7
4 Installation ....................................................................... 7
4.1 Mounting requirements ................................................................. 7
4.2 Mounting the measuring device ............................................................8
4.3 Post-mounting check ................................................................... 9
5 Electrical connection .............................................................. 9
5.1 Connection requirements ................................................................ 9
5.2 Connecting the measuring device ......................................................... 10
5.3 Connecting the sensor cables ............................................................. 12
5.4 Ensuring the degree of protection ......................................................... 14
5.5 Post-connection check ..................................................................15
6 Operation options ............................................................... 16
6.1 Overview of operation options ............................................................ 16
6.2 Access to operating menu via web browser .................................................. 18
6.3 Access to the operating menu via operating tools .............................................. 18
7 Commissioning .................................................................. 18
7.1 Post-installation check ................................................................. 18
7.2 Switching on the device ................................................................. 18
7.3 Configuring the device ................................................................. 18
8 Maintenance .................................................................... 19
1 About this document
1.1 Symbols used
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
Safety instructions iTEMP TMT86
4 Endress+Hauser
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2 Tool symbols
Symbol Meaning
A0011219
Phillips head screwdriver
1.3 Registered trademarks
PROFINET®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
2 Safety instructions
2.1 Requirements for personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the
following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Personnel must be authorized by the plant owner/operator.
‣Be familiar with federal/national regulations.
‣Before starting work: personnel must read and understand the instructions in the manual
and supplementary documentation as well as the certificates (depending on the
application).
‣Personnel must follow instructions and comply with general policies.
The operating personnel must fulfill the following requirements:
‣Personnel are instructed and authorized according to the requirements of the task by the
facility's owner-operator.
‣Personnel follow the instructions in this manual.
iTEMP TMT86 Safety instructions
Endress+Hauser 5
2.2 Intended use
The device is a universal and user-configurable temperature transmitter with either one or
two sensor inputs for a resistance thermometer (RTD), thermocouples (TC), resistance and
voltage transmitters. The head transmitter version of the device is intended for mounting in a
terminal head (flat face) as per DIN EN 50446. The device is also optionally available in a
version that is integrated into a field housing. It is also possible to mount the device on a DIN
rail using the optional DIN rail clip.
If the device is used in a manner not specified by the manufacturer, the protection provided by
the device may be impaired.
The manufacturer is not liable for damage caused by using the device incorrectly or for
purposes for which it was not intended.
2.3 Workplace safety
When working on and with the device:
‣Wear the required personal protective equipment as per national regulations.
2.4 Operational safety
‣Operate the device only if it is in proper technical condition, free from errors and faults.
‣The operator is responsible for ensuring trouble-free operation of the device.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous
area (e.g. explosion protection or safety equipment):
‣Based on the technical data on the nameplate, check whether the ordered device is
permitted for the intended use in the hazardous area. The nameplate can be found on the
side of the transmitter housing.
‣Observe the specifications in the separate supplementary documentation that is an integral
part of these instructions.
Electromagnetic compatibility
The measuring system complies with the general safety requirements and EMC requirements
of the IEC/EN 61326 series and the APL EMC Test Specification.
2.5 Product safety
This product is designed in accordance with good engineering practice to meet state-of-the-
art safety requirements and has been tested and left the factory in a condition in which it is
safe to operate.
2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
Incoming acceptance and product identification iTEMP TMT86
6 Endress+Hauser
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.
3 Incoming acceptance and product identification
3.1 Incoming acceptance
1. Unpack the temperature transmitter carefully. Are the contents or packaging
undamaged?
Do not install damaged components, as otherwise the manufacturer cannot
guarantee the material resistance or ensure compliance with the original safety
requirements, and therefore cannot be held responsible for any resulting damage.
2. Is the delivery complete or is anything missing? Check the scope of delivery against your
order.
3. Does the nameplate match the order information on the delivery note?
4. Are the technical documentation and all other necessary documents provided? If
applicable: are the Safety Instructions (e.g. XA) for hazardous areas provided?
If one of these conditions is not met, please contact the manufacturer's sales office.
3.2 Product identification
The following options are available for identification of the device:
• Nameplate specifications
• Extended order code with breakdown of the device features on the delivery note
• Enter the serial number from the nameplate in the W@M Device Viewer
(www.endress.com/deviceviewer): all data relating to the device and an overview of the
Technical Documentation supplied with the device are displayed.
• Enter the serial number on the nameplate into the Endress+Hauser Operations App or scan
the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations App:
all the information about the device and the technical documentation pertaining to the
device is displayed.
Approval in hazardous areas: Ensure that the information on the nameplate matches the
enclosed Ex documentation (XA...).
3.2.1 Name and address of manufacturer
Name of manufacturer: Endress+Hauser Wetzer GmbH + Co. KG
Model/type reference: TMT86
Address of manufacturer: Obere Wank 1, D-87484 Nesselwang or www.endress.com
iTEMP TMT86 Installation
Endress+Hauser 7
3.3 Certificates and approvals
For certificates and approvals valid for the device: see the data on the nameplate
Approval-related data and documents: www.endress.com/deviceviewer → (enter the
serial number)
3.4 Storage and transport
Storage temperature: –52 to +100 °C (–61.6 to +212 °F)
Humidity
• Condensation permitted with head transmitter
• Max. rel. humidity: 95 % as per IEC 60068-2-30
Pack the device for storage and transportation in such a way that it is reliably protected
against impact and external influences. The original packaging provides optimum
protection.
Avoid the following environmental influences during storage and transport:
• Direct sunlight
• Vibration
• Aggressive media
4 Installation
4.1 Mounting requirements
4.1.1 Mounting location
Head transmitter:
• in the terminal head, flat face, as per DIN EN 50446, direct mounting on insert with cable
entry (middle hole 7 mm)
• in the field housing, separated from the process
• with DIN rail clip on DIN rail as per IEC 60715, TH35
For use in hazardous areas, the limit values specified on the certificates and approvals must be
observed (see Ex Safety Instructions).
4.1.2 Important ambient conditions
• Operating height: up to 4000 m (4374.5 yards) above mean sea level
• Overvoltage category: overvoltage category II
• Pollution degree: 2
• Insulation class: class III
• Ambient temperature: –40 to +85 °C (–40 to 185 °F);
Optional –50 to +85 °C (–58 to 185 °F), –52 to +85 °C (–61.6 to 185 °F)
• Head transmitter climate class: C1 (–5 to +45 °C (23 to 113 °F), 5 to 95 % r.h.) as per IEC
60654-1
Installation iTEMP TMT86
8 Endress+Hauser
• Condensation permitted with head transmitter
• Max. rel. humidity: 95 % as per IEC 60068-2-30
• Degree of protection:
• Head transmitter with screw terminals: IP00, with push-in terminals: IP30. When
installed, the degree of protection depends on the terminal head or field housing used.
• When installing in field housing TA30x: IP IP66/68 (NEMA Type 4x encl.)
4.2 Mounting the measuring device
A Phillips head screwdriver is required to mount the device:
• Maximum torque for securing screws = 1 Nm (¾ foot-pound), screwdriver: Pozidriv Z2
• Maximum torque for screw terminals = 0.35 Nm (¼ foot-pound), screwdriver: Pozidriv Z1
4.2.1 Head transmitter mounting
1
2
3
4
5
6
7
9
8
1 2 3 4 5 1234
120 mm
(4.72 in)
120 mm
(4.72 in)
Item A Item B
Item C
A0048481
1 Head transmitter mounting (three versions)
iTEMP TMT86 Electrical connection
Endress+Hauser 9
Mounting typical of North America
12 3 456
A0008520
2 Head transmitter mounting
NOTICE
The terminal head cover must be secured properly to meet the requirements for
explosion protection.
‣After wiring, securely screw the terminal head cover back on.
4.3 Post-mounting check
After installing the device, run the following final checks:
Device health and specifications Notes
Is the device undamaged (visual inspection)? -
Do the ambient conditions match the device specification (e.g. ambient temperature,
measuring range, etc.)?
→ 7
5 Electrical connection
5.1 Connection requirements
A Phillips head screwdriver is required to wire the head transmitter with screw terminals. No
tools are required for the version with push-in terminals.
Electrical connection iTEMP TMT86
10 Endress+Hauser
LCAUTION
‣Switch off the power supply before installing or connecting the device. Non-compliance
may result in the destruction of parts of the electronics.
‣When connecting Ex-certified devices, please take special note of the instructions and
connection schematics in the Ex-specific supplement to these Operating Instructions.
‣Do not occupy the display connection. An incorrect connection can destroy the electronics.
‣Before connecting the power supply, connect the potential equalization line to the external
ground terminal.
‣The device may only be powered by a power unit with an energy-limited circuit in
accordance with UL/EN/IEC 61010-1, Section 9.4 and the requirements of Table 18.
5.2 Connecting the measuring device
Head transmitter:
A
C
RD
WH
B
1+
2-
7
6
5
4
3
RD (BK)
WH (YE)
D
E
F
1
2
A0046019
3 Assignment of terminal connections for head transmitter
A Sensor input 1, RTD and Ω, 4-, 3- and 2-wire
B Sensor input 1, TC and mV
C Sensor input 2, RTD and Ω, 3- and 2-wire
D Sensor input 2, TC and mV
E Display connection, service interface
F Bus terminator and power supply
NOTICE
‣ ESD - Electrostatic discharge. Protect the terminals from electrostatic discharge. Non-
compliance may result in the destruction or malfunction of parts of the electronics.
5.2.1 Fieldbus connection
Devices can be connected to the fieldbus in two ways:
Autres manuels pour iTEMP TMT86
1
Table des matières
Autres manuels Endress+Hauser Émetteur
Endress+Hauser
Endress+Hauser Promag Series Manuel utilisateur
Endress+Hauser
Endress+Hauser RMA42 Caractéristiques techniques
Endress+Hauser
Endress+Hauser cerabar M PMP 46 Manuel
Endress+Hauser
Endress+Hauser iTEMP TMT162 Manuel utilisateur
Endress+Hauser
Endress+Hauser RMA42 Caractéristiques techniques
Endress+Hauser
Endress+Hauser RMA42 Manuel utilisateur
Endress+Hauser
Endress+Hauser iTEMP TMT71 Instructions d'installation
Endress+Hauser
Endress+Hauser Liquisys M CUM223 Manuel utilisateur
Endress+Hauser
Endress+Hauser iTEMP TMT82 Caractéristiques techniques
Endress+Hauser
Endress+Hauser Proline Promag 50 Manuel utilisateur
Endress+Hauser
Endress+Hauser iTEMP PCP TMT 121 Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquisys M CPM 223 Manuel utilisateur
Endress+Hauser
Endress+Hauser iTEMP TMT162 Caractéristiques techniques
Endress+Hauser
Endress+Hauser CM14-AAK Manuel utilisateur
Endress+Hauser
Endress+Hauser FHX50 Manuel utilisateur
Endress+Hauser
Endress+Hauser Proline 500 HART Caractéristiques techniques
Endress+Hauser
Endress+Hauser Liquisys M CCM223 Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquisys M CXM 223 Manuel utilisateur
Endress+Hauser
Endress+Hauser smartgrad TMD833 Manuel utilisateur
Endress+Hauser
Endress+Hauser Proline Promass O 100HART Caractéristiques techniques
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
