Endress+Hauser T-switch ATT11 Manuel utilisateur

KA001A/05/e/03.02

t-switch

ATT11

Flow Limit Switch for Liquids and Gases

KA00053D/22/EN/01.11

Contents

Safety Notes 3

Handling 3

Mounting and Installation 4-10

Electrical Connection 11

Operation 12

DIL Switch Explanations 13-14

Quick Set-up Guidelines 15

Set-up Explanation 16

Set-up Procedure:

Set Zero Flow 17

Set Maximum Flow 18

Set Setpoint (AUTO) 19

Set Setpoint (MANUAL) 20

Set Medium Selection 21

Set Relay Mode 21

Diagnostics/Error Codes 22

Technical Data 23-24

Contact Addresses 25-26

Safety Notes

The t-switch ATT11 is designed for flow limit detection in liquids

and gases. The ATT11 should be installed, connected,

commissioned, operated and maintained by qualified and authorised

personnel only, under strict observance of these operating instructions,

any relevant standards, legal requirements and where appropriate,

the certificate. Do not attempt to install or remove the instrument

under pressurised conditions.

Hold by housing or

extension tube; do

not hold by sensor.

Place sensor end

up. Sensor impact

may cause damage.

Handling

Mounting and

Installation

Guidelines for Threaded Process Connections

BSP 3/4" (G)

Use appropriately sized sealing

washer.

3/4" NPT

Use a suitable thread tape to achieve

a reliable seal.

Always use a spanner to tighten

the t-switch process connection.

Do not use housing to turn.

Note

For other types of process fittings follow standard good working practices.

Mounting and

Installation

Sensor Orientation Markings

Every process connection has an orientation mark stamped on it.

The locations of these marks are shown below and for optimum

performance it is important that it is facing the flow.

Mounting and

Installation

Sensor Orientation and

Flow Direction

It is important that the sensor is installed, such that the orientation

mark is positioned upstream to the flowing fluid.

If the sensor is not installed as above it may affect the performance

of the instrument.

Note

Welding instructions are provided with each sensor and care should be taken to read

them prior to installation. 6

5º

Flow

Direction

Mounting and

Installation

Insertion Depth

For optimum measuring performance the active area should be

positioned anywhere between 5% and 50% of the internal pipe diameter.

The sensor tip should be in contact with the medium at all times.

Each form of process connector has an orientation mark that should

or = to sign be positioned in line facing the oncoming flow.

50%

10%

50%

For pipe diameters <DN250 For pipe diameters ≥DN250

Mounting and

Installation

Horizontal Pipeline Positioning

Vertical Pipeline Flow Direction

✓

✕Liquid

Gas ✓

✓Liquid

Gas

LIQUID

GAS

LIQUID (Partially Full)

LIQUID

GAS

LIQUID

GAS

LIQUID

GAS

LIQUID (Dirty)

>25 dia

>50 dia

>10 dia

Mounting and

Installation

Good installation Practice Summary

Avoid installing in areas of extreme flow turbulence. For example;

Directly after bends or expansions/reductions.

Directly downstream of isolation and control

valves especially if partially opened.

Directly after pumps, fans and compressors.

Note

All downstream dimensions provided are to be used as a guideline only and whenever

possible greater dimensions should be considered.

>2 dia

Table des matières

Autres manuels Endress+Hauser Changer

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Manuel utilisateur

Endress+Hauser

Endress+Hauser nivotester FTW 420 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiphant FTL64 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Soliphant M FTM50 Manuel

Endress+Hauser

Endress+Hauser Liquiphant FTL51B Manuel utilisateur

Endress+Hauser

Endress+Hauser FEC 22 Manuel utilisateur

Endress+Hauser

Endress+Hauser Soliswitch FTE20 Manuel utilisateur

Endress+Hauser

Endress+Hauser Nivector FTI26 Manuel

Endress+Hauser

Endress+Hauser nivotester FTC 420 Manuel utilisateur

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiphant FTL51B Manuel utilisateur

Endress+Hauser

Endress+Hauser Soliphant T FTM20 Manuel utilisateur

Endress+Hauser

Endress+Hauser Nivotester FTL375P Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquipoint T FTW32 Manuel utilisateur

Endress+Hauser

Endress+Hauser Flowphant T DTT31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiphant FTL64 Manuel utilisateur

Endress+Hauser

Endress+Hauser OTR31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Ceraphant T PTC31 Manuel utilisateur

Endress+Hauser

Endress+Hauser Liquiphant M FTL50 Manuel utilisateur

Endress+Hauser

Endress+Hauser nivector FTC 968 Manuel utilisateur

Endress+Hauser

Endress+Hauser nivotester FTL 325 P Manuel

Endress+Hauser

Endress+Hauser Nivotester FTC325 Manuel utilisateur

Endress+Hauser

Endress+Hauser RTA421 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Endress+Hauser t-switch ATT11 Manuel utilisateur

Manuels Changer populaires d'autres marques