Emerson Rosemount 5408 Manuel utilisateur
Quick Start Guide
00825-0100-4408, Rev BB
June 2019
Rosemount™ 5408 and 5408:SIS Level
Transmitters
Cone Antenna
Contents
About this guide...........................................................................................................................3
Confirm approval type..................................................................................................................5
Mount the transmitter..................................................................................................................6
Align transmitter head............................................................................................................... 16
Adjust display orientation (optional).......................................................................................... 18
Prepare the electrical connections..............................................................................................19
Connect wiring and power up.....................................................................................................26
Configure transmitter using Guided Setup................................................................................. 30
Assemble the segmented cone antenna.....................................................................................32
Quick Start Guide June 2019
2 Rosemount 5408 and 5408:SIS Level Transmitters
1 About this guide
This Quick Start Guide provides basic guidelines for the Rosemount 5408
and 5408:SIS Level Transmitters. Refer to the Rosemount 5408 and 5408:SIS
with HART® Reference Manual and Rosemount 5408 with FOUNDATION™
Fieldbus Reference Manual for more instructions. The manuals and this
guide are also available electronically on Emerson.com/Rosemount.
WARNING
Failure to follow safe installation and servicing guidelines could result in
death or serious injury.
•Make sure the transmitter is installed by qualified personnel and in
accordance with applicable code of practice.
•Use the equipment only as specified in this manual. Failure to do so may
impair the protection provided by the equipment.
•For installations in hazardous locations, the transmitter must be installed
according to the Rosemount 5408 and 5408:SIS Product Certifications
document and System Control Drawing (D7000002-885).
•Repair, e.g. substitution of components etc., may jeopardize safety and
is under no circumstances allowed.
Explosions could result in death or serious injury.
•Verify that the operating atmosphere of the transmitter is consistent
with the appropriate hazardous locations certifications.
•Before connecting a handheld communicator in an explosive
atmosphere, ensure the instruments are installed in accordance with
intrinsically safe or non-incendive field wiring practices.
•In Explosion-proof/Flameproof and Non-Incendive/Type n installations,
do not remove the transmitter covers when power is applied to the unit.
•Both transmitter covers must be fully engaged to meet Explosion-proof/
Flameproof requirements.
Electrical shock could cause death or serious injury.
•In Explosion-proof/Flameproof and Non-Incendive/Type n installations,
avoid contact with the leads and terminals. High voltage that may be
present on leads can cause electrical shock.
•Make sure the mains power to the transmitter is off and the lines to any
other external power source are disconnected or not powered while
wiring the transmitter.
June 2019 Quick Start Guide
Quick Start Guide 3
WARNING
Process leaks could result in death or serious injury.
•Make sure that the transmitter is handled carefully. If the process seal is
damaged, gas might escape from the tank.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to
and/or misconfiguration of end users’ equipment. This could be
intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and
fundamental to protecting your system. Restrict physical access by
unauthorized personnel to protect end users’ assets. This is true for all
systems used within the facility.
CAUTION
Hot surfaces
The flange and process seal may be hot at high process temperatures. Allow
to cool before servicing.
Quick Start Guide June 2019
4 Rosemount 5408 and 5408:SIS Level Transmitters
2 Confirm approval type
For hazardous locations transmitters labeled with multiple approval types:
Procedure
Permanently mark the checkbox of the selected approval type(s).
Figure 2-1: Label with Multiple Approval Types
June 2019 Quick Start Guide
Quick Start Guide 5
3 Mount the transmitter
3.1 Flanged version
Prerequisites
If applicable, assemble the segmented cone antenna (see Assemble the
segmented cone antenna).
Procedure
1. Place a suitable gasket on the tank flange.
2. Lower transmitter with antenna and flange into the nozzle.
3. Tighten bolts and nuts with sufficient torque for the flange and
gasket choice.
Postrequisites
Align the transmitter head (see Align transmitter head).
Quick Start Guide June 2019
6 Rosemount 5408 and 5408:SIS Level Transmitters
3.2 Flanged version with air purge ring (option code PC1)
Prerequisites
If applicable, assemble the segmented cone antenna (see Assemble the
segmented cone antenna).
Procedure
1. Place a suitable gasket on the tank flange.
2. Place the purge ring over the gasket.
3. Place a suitable gasket over the purge ring.
Note
A minimum gasket thickness of 0.125 in. (3.2 mm) is required for
flanges with protective plate design.
4. Lower transmitter with antenna and flange into the nozzle.
$
A. Antenna with air purge holes
June 2019 Quick Start Guide
Quick Start Guide 7
5. Tighten bolts and nuts with sufficient torque for the flange and
gasket choice.
$
A. 1.0 in. (25.5 mm)
6. Connect the air purging system. Use thread sealant or suitable gasket
according to your site procedures.
or
A. G⅜-in.
B. 0.4 in. (10 mm)
Table 3-1: Incoming Air Supply Specification
Maximum pressure Recommended pressure
190 psi (13 bar) 100 to 115 psi (7 to 8 bar)
Postrequisites
Align the transmitter head (see Align transmitter head).
Quick Start Guide June 2019
8 Rosemount 5408 and 5408:SIS Level Transmitters
3.3 Threaded version, antenna diameter smaller than thread
diameter
3.3.1 Threaded tank connection
Prerequisites
If applicable, assemble the segmented cone antenna (see Assemble the
segmented cone antenna).
Procedure
1. Apply anti-seize paste or PTFE tape on threads according to your site
procedures.
Gasket may be used as a sealant for adapters with 1½- or 2-in.
BSPP (G) threads.
2. Mount the transmitter on the tank.
$
A. Gasket (for 1½-in. and 2-in. BSPP (G) threads only)
June 2019 Quick Start Guide
Quick Start Guide 9
Postrequisites
Align the transmitter head (see Align transmitter head).
3.3.2 Flanged tank connection
Prerequisites
If applicable, assemble the segmented cone antenna (see Assemble the
segmented cone antenna).
Procedure
1. Place a suitable gasket on the tank flange.
2. Place the customer supplied flange over the gasket.
3. Tighten the bolts and nuts with sufficient torque for the flange and
gasket choice.
4. Apply anti-seize paste or PTFE tape on threads according to your site
procedures.
Gasket may be used as a sealant for adapters with 1½- or 2-in.
BSPP (G) threads.
Quick Start Guide June 2019
10 Rosemount 5408 and 5408:SIS Level Transmitters
Autres manuels pour Rosemount 5408
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Emerson Émetteur
Emerson
Emerson Rosemount 3308 Series Manuel utilisateur
Emerson
Emerson PT5N FLR Series Manuel utilisateur
Emerson
Emerson Micro Motion 5700 Manuel utilisateur
Emerson
Emerson PENBERTHY MGT-362 Manuel
Emerson
Emerson Rosemount 3051HT Manuel utilisateur
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 848T Manuel utilisateur
Emerson
Emerson Rosemount 644h Manuel utilisateur
Emerson
Emerson Rosemount 848T Manuel utilisateur
Emerson
Emerson Rosemount 3101 Manuel utilisateur
Emerson
Emerson Fisher 4200 Series Manuel utilisateur
Emerson
Emerson MICRO MOTION 2700 Manuel du propriétaire
Emerson
Emerson Rosemount 3051 Manuel utilisateur
Emerson
Emerson Rosemount 148 Manuel utilisateur
Emerson
Emerson Micro Motion 4200 Manuel utilisateur
Emerson
Emerson Rosemount 3051HT Manuel utilisateur
Emerson
Emerson Rosemount 1152 Alphaline Manuel utilisateur
Emerson
Emerson Magtech LTM-350 Series Manuel
Emerson
Emerson Micro Motion 9739 MVD Guide rapide
Emerson
Emerson Rosemount 8732E Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
