Emerson Fisher V500 Manuel utilisateur

www.Fisher.com

FishertV500 Rotary Globe Control Valve

Contents

Introduction 1.................................

Scope of Manual 1.............................

Description 1.................................

Specifications 2...............................

Installation 2..................................

Maintenance 7.................................

Packing Maintenance 8.........................

Replacing Retainer, Seat Ring, and Face Seals 10....

Replacing Valve Plug, Shaft, and Bearings 15.......

Adjusting Actuator Travel 20....................

Changing Valve Flow Direction 21................

Changing Actuator Mounting Style 21............

Parts Ordering 21...............................

Parts Kits 22...................................

Parts List 24...................................

Figure 1. Fisher V500 Flanged Rotary Control Valve

with 1061 Actuator and FIELDVUE™ DVC6200 Digital

Valve Controller

W8380-1

Introduction

Scope of Manual

This instruction manual provides installation, operation, maintenance, and parts ordering information for NPS 1

through 8 Fisher V500 eccentric plug rotary control valves. Refer to separate manuals for information concerning the

actuator and accessories.

Do not install, operate, or maintain a V500 valve without being fully trained and qualified in valve, actuator, and

accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you

have any questions about these instructions, contact your Emerson sales office or Local Business Partner before

proceeding.

Unless otherwise noted, all NACE references are to NACE MR0175‐2002.

Description

The V500 rotary control valve is a flanged (figure 1) or flangeless valve with a self‐centering seat, eccentrically rotating

plug, and splined valve shaft. Suitable for forward or reverse flow use, this valve mates with a variety of actuators to

provide throttling or on‐off service. Both flanged and flangeless valves mate with CL150, 300, or 600 raised face

pipeline flanges or DIN PN10 through PN100 flanges.

Instruction Manual

D100423X012

V500 Valve

July 2017

Instruction Manual

D100423X012

V500 Valve

July 2017

Table 1. Specifications

Valve Sizes(1)

NPS J1, J1-1/2, J2, J3, J4, J6, and J8.

DN 25, 40, 50, 80, 100, 150 and 200 sizes are also

available.

End Connection Style

JRaised‐face flanges, Jring‐type joint flanges

(ASME B16.5), Jor flangeless valve body designed to

fit between raised face flanges. JCL150, JCL300,

or JCL600; (CL600 is not available in NPS 6 and 8

flangeless valve bodies). DIN PN10 through PN100

flanges also available; consult your Emerson sales

office or Local Business Partner.

Maximum Inlet Pressure(2)

Consistent with applicable ASME B16.34 or

EN 12516-1 ratings

Shutoff Classification

Class IV per ANSI/FCI 70‐2 and IEC 60534‐4 (0.01% of

valve capacity at full travel), for either flow direction.

Leak rates for full and restricted port valves are based

on full port capacities. Reduced port valves seat at the

full port diameter.

Flow Characteristic

Modified linear

Flow Direction

JReverse Flow (Standard Direction): Past valve plug

and through seat ring tends to close the valve,

recommended for erosive and general service

JForward Flow: Through seat ring and past valve

plug; tends to open the valve, recommended for high

pressure drop and high cycle service

Actuator Mounting

JLeft‐hand or Jright‐hand as viewed from the

upstream side of the valve. See figure 2

Valve Plug Rotation

Counterclockwise to close (when viewed from

actuator side of valve) through 90 degrees of valve

plug rotation

Valve/Actuator Action

With diaphragm or piston rotary actuator,

field‐reversible between Jpush‐down‐to‐close

(extending actuator rod closes the valve) and

Jpush‐down‐to‐open (extending actuator rod

opens the valve)

Shaft Diameters(3) and Approximate Weights

See table 2

1. The Valve Size shown in this manual refers to Nominal Pipe Size (NPS).

2. The pressure or temperature limits in this manual and any applicable standard limitations should not be exceeded.

3. Shaft diameter and spline end must match available shaft diameter of actuator.

Installation

WARNING

Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal

injury.

To avoid personal injury or property damage resulting from the sudden release of pressure, do not install the valve

assembly where service conditions could exceed the limits given on the appropriate nameplates, or the mating pipe flange

rating. Use pressure‐relieving devices as required by government or accepted industry codes and good engineering

practices.

Check with your process or safety engineer for any other hazards that may be present from exposure to process media.

If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this

instruction manual.

CAUTION

When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature,

pressure drop, and controlled fluid conditions. Responsibility for the safety of process media and compatibility of valve

Instruction Manual

D100423X012

V500 Valve

July 2017

materials with process media rests solely with the purchaser and end‐user. Since some valve body/trim material

combinations are limited in their pressure drop and temperature ranges, do not apply any other conditions to the valve

without first contacting your Emerson sales office or Local Business Partner.

Table 2. Shaft Diameter and Approximate Weights

VALVE SIZE,

NPS

SHAFT DIAMETER APPROXIMATE WEIGHT

Flanged Flangeless

Through

Valve At Spline End CL150 CL300 CL600 CL150 CL300 CL600

mm kg kg

1 12.7 12.7 5.4 5.9 5.9 3.6 3.6 3.6

1-1/2 15.9 15.9 8.6 9.5 10 5.4 5.4 5.4

2 15.9 15.9 9.5 11 13 8.2 8.2 8.2

325.4 25.4 19 24 26 16 16 16

25.4 19.1

4 31.8 31.8 36 42 50 34 34 34

638.1 38.1 54 69 93 50 50 - - -

38.1 31.8

8 38.1 38.1 79 98 135 57 68 - - -

Inches lbs lbs

1 1/2 1/2 12 13 13 8 8 8

1-1/2 5/8 5/8 19 21 23 12 12 12

2 5/8 5/8 21 25 28 18 18 18

31 1 42 52 57 35 35 35

1 3/4

4 1‐1/4 1‐1/4 79 93 111 75 75 75

61‐1/2 1‐1/2 120 152 204 110 110 - - -

1‐1/2 1‐1/4

8 1‐1/2 1‐1/2 75 217 298 125 150 - - -

Key numbers in this procedure are shown in figure 11 (NPS 1 and 1-1/2 valves) or figure 13 (NPS 2 through 8 valves)

unless otherwise indicated.

CAUTION

To prevent product damage during storage, keep the valve body cavity dry and clear of foreign material.

1. If the valve is to be stored before installation, protect the flange mating surfaces and keep the valve body cavity dry

and clear of foreign material.

2. Install a three‐valve bypass around the control valve assembly if continuous operation will be necessary during

inspection and maintenance of the valve.

3. A V500 valve is normally shipped as part of a control valve assembly, with a power or manual actuator mounted on

the valve. If the valve and actuator have been purchased separately or if the actuator has been removed from the

valve, mount the actuator according to the Actuator Mounting procedure. Also, adjust the actuator travel using the

Adjusting Actuator Travel procedure before installing the valve. The necessary measurements cannot be made with

the valve installed.

4. Before starting the actual installation of the valve, determine the proper installation orientation of the valve plug

(key 2) and actuator. Determine the flow direction of the process fluid through the valve. See figure 2.

Instruction Manual

D100423X012

V500 Valve

July 2017

Figure 2. Index Marks for Actuator Lever Orientation

43A5323‐D

C0586‐1

Instruction Manual

D100423X012

V500 Valve

July 2017

Table 3. Line Stud (Key 36)

M(1)

Valve Size Pressure Rating Qty Bolt Size Bolt Length

NPS Inches

CL150 4 5/8-11 UNC 10.62

CL300 6 3/4-10 UNC 11.12

CL600 6 3/4-10 UNC 11.50

CL150 6 5/8-11 UNC 11.44

CL300 6 3/4-10 UNC 12.12

CL600 6 7/8- 9 UNC 13.62

6CL150 5 3/4-10 UNC 13.62

CL300 6 3/4-10 UNC 14.38

8CL150 8 3/4-10 UNC 13.62

CL300 10 7/8- 9 UNC 15.38

1. These bolts may be installed from either end of the valve.

Table 4. Line Stud (Key 36)(1)

Valve Size Pressure Rating Qty Bolt Size Bolt Length

NPS Inches

6CL150 6 3/4-10 UNC 5.00

CL300 6 3/4-10 UNC 5.00

8CL150 - - - - - - - - -

CL300 4 7/8- 9 UNC 5.62

1. Use instead of cap screws.

Table 5. Cap Screw (Key 37)

N P

Valve Size Pressure Rating Qty Bolt Size Bolt Length Overall Length

NPS Inches Inches

CL150 - - - - - - - - - - - -

CL300 4 3/4-10 UNC 2.38 2.88

CL600 4 3/4-10 UNC 2.38 2.88

CL150 4 5/8-11 UNC 2.00 2.44

CL300 4 3/4-10 UNC 2.38 2.88

CL600 4 7/8- 9 UNC 2.75 3.38

Figure 3. Line Bolt Dimensions for Flangeless Valve Bodies (also see tables 3, 4 and 5)

LINE

STUDS LINE STUDS

CAP

SCREWS

NOTE:

USED INSTEAD OF CAP SCREWS

A4347

Instruction Manual

D100423X012

V500 Valve

July 2017

Figure 4. Optional Shaft‐to‐Body Bonding Strap Assembly

VALVE BODY ACTUATOR

VIEW A‐A

37A6528‐A

A3143‐2

Note

For best shutoff performance and to reduce bearing wear, it is recommended that you install the valve shaft in a horizontal

direction. See figure 1.

5. Before installing the valve, make sure the flow direction arrow (key 32) on the valve matches the actual process fluid

flow direction through the valve for the application where the valve will be installed.

6. Install the flange gaskets and insert the valve between the mating pipeline flanges. For flangeless valve bodies, also

make sure the mating line flanges are aligned. Use flat sheet gaskets compatible with the process media, or spiral

wound gaskets with compression‐controlling center rings.

Ceramic Trim

Some types of ceramic trim, including the VTC (very tough ceramic) variety, can create a spark under certain

circumstances. When the edge of a ceramic part is struck against a second ceramic part with enough force, a spark can

be created.

WARNING

Avoid personal injury and property damage from ignition of process fluid caused by sparks from ceramic trim.

Do not use ceramic trim where the process fluid is unstable or if it is an explosive mixture (such as air and ether).

WARNING

The valve drive shaft is not necessarily grounded to the pipeline when installed. Personal injury or property damage could

result if the process fluid or the atmosphere around the valve is flammable, from an explosion caused by a discharge of

static electricity from the valve components. If the valve is installed in a hazardous area, electrically bond the drive shaft to

the valve.

Instruction Manual

D100423X012

V500 Valve

July 2017

1. Prepare to install the line bolts and nuts. For flangeless valves, consult figure 3 before installing the line bolts and

nuts. Figure 3 shows the line bolt clearances required when installing flangeless valves.

Note

Standard PTFE packing is composed of a partially conductive carbon‐filled PTFE female adaptor with PTFE V‐ring packing. Standard

graphite packing is composed of all conductive graphite ribbon packing rings. Alternate shaft‐to‐valve body bonding is available

for hazardous service areas where the standard packing is not sufficient to bond the shaft to the valve (see the following step).

2. For hazardous applications, attach the bonding strap assembly (key 131) to the shaft with the clamp (key 130) and

connect the other end of bonding strap assembly to the valve body with the cap screw (key 25). See figure 4.

For all valve bodies, install the line bolts and nuts; then, tighten them using accepted bolting procedures. These

procedures include, but are not limited to, lubricating the line bolts and hex nuts and tightening the nuts in a crisscross

sequence to ensure proper gasket load.

3. If a purge is desired for the purged bearing construction, remove the pipe plugs (keys 29 and 24) and install the

purge lines. Purge pressure should be greater than the pressure within the valve and the purge fluid should be as

clean as possible.

4. Connect pressure lines to the actuator as indicated in the actuator instruction manual. When a manual actuator is

used with a power actuator, install a bypass valve on the power actuator (if not already supplied) for use during

manual operation.

WARNING

Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packing

might require some readjustment to meet specific service conditions. Check with your process or safety engineer for any

other hazards that may be present from exposure to process media.

If the valve has ENVIRO‐SEALtlive‐loaded packing installed readjustment will probably not be required. See the

Emerson Automation Solutions instruction manual entitled ENVIRO‐SEAL Packing System for Rotary Valves

(D101643X012) for packing instructions. If you wish to convert your present packing arrangement to ENVIRO‐SEAL

packing, refer to the retrofit kits listed in the Parts Kit section later in this manual.

Maintenance

WARNING

Avoid personal injury or property damage from sudden release of process pressure or bursting of parts. Before performing

any maintenance operations:

D Do not remove the actuator from the valve while the valve is still pressurized.

D Always wear protective gloves, clothing and eyewear when performing any maintenance operations to avoid personal

injury.

D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the

actuator cannot suddenly open or close the valve.

D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure

from both sides of the valve. Drain the process media from both sides of the valve.

Instruction Manual

D100423X012

V500 Valve

July 2017

D Vent the power actuator loading pressure and relieve any actuator spring precompression.

D Use lock‐out procedures to be sure that the above measures stay in effect while you work on the equipment.

D The valve packing area may contain process fluids that are pressurized, even when the valve has been removed from the

pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings.

D Check with your process or safety engineer for any other hazards that may be present from exposure to process media.

Valve parts are subject to normal wear and must be inspected and replaced as necessary. The frequency of inspection

and replacement depends upon the severity of service conditions.

As used in these instructions, the term “actuator” refers to power actuators (such as pneumatic diaphragm or piston

actuators) or manual actuators (such as handwheel or handlever actuators).

Packing Maintenance

Key numbers are referenced in figures 11 and 13 unless otherwise indicated.

Note

For the ENVIRO‐SEAL packing system, refer to the Parts Ordering section for retrofit kits and parts kits(see figure 14). Refer to the

separate ENVIRO‐SEAL instruction manual for maintenance instructions.

Standard ENVIRO‐SEAL packing systems can be used in vacuum service with packing rings in the standard orientation. It is not

necessary to reverse the ENVIRO‐SEAL PTFE packing rings.

Stopping Leakage

All maintenance procedures in this section may be performed with the valve body (key 1) in the line.

For packing other than spring‐loaded packings, leakage around the packing follower (key 14) can be stopped by

tightening the packing flange nuts (key 16). If leakage cannot be stopped in this manner, replace the packing

according to the Replacing Packing procedure.

If the packing is relatively new and tight on the valve shaft (key 3), and if tightening the packing nuts does not stop

leakage, it is possible that the valve shaft is worn or nicked so that a seal cannot be made. If the leakage comes from

the outside diameter of the packing, it is possible that the leakage is caused by nicks or scratches on the packing box

wall. Inspect the shaft and packing box wall for nicks or scratches when performing the following procedures.

Replacing Packing

Note

If the valve has ENVIRO‐SEAL live‐loaded packing installed, see the separate ENVIRO‐SEAL instruction manual.

This procedure may be performed without removing the actuator from the valve body if adding PTFE/composition

packing rings as a temporary measure. However, the actuator must be removed if replacing any other kind of packing

or if the metal packing parts (keys 14, 17, and, if used, 18) need to be replaced.

Instruction Manual

D100423X012

V500 Valve

July 2017

Removing the Packing

1. Isolate the control valve from the line pressure, release pressure from both sides of the valve, and drain the process

media from both sides of the valve. If using a power actuator, also shut off all pressure lines to the power actuator,

release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures stay in effect

while you work on the equipment.

CAUTION

When the actuator is removed from the valve, do not use a hammer or similar tool to drive the lever or actuator off the

valve shaft. Driving the lever or actuator off the valve shaft could damage the valve plug, seal, and valve.

If necessary, use a wheel puller to remove the lever or actuator from the valve shaft. It is okay to tap the wheel puller screw

lightly to loosen the lever or actuator, but hitting the screw with excessive force could damage the valve plug, seal, and

valve.

2. If necessary, remove the cap screws (key 25) and hex nuts (key 26). Then remove the actuator while referring to the

actuator manual for assistance.

3. Remove the packing nuts (key 16) and packing follower (key 14).

4. Remove the old packing rings (key 13), packing box ring (key 17), and, if used, the lantern ring (key 18).

CAUTION

Do not scratch the valve shaft or packing box wall. Scratching these surfaces could cause leakage.

5. Clean all accessible metal parts and surfaces to remove particles that would prevent the packing from sealing.

6. If necessary, complete the steps in the Replacing the Valve Plug, Shaft, and Bearings section, and return to the

Installing Packing steps below.

Installing Packing

1. Install the new packing rings and packing box ring by stacking the parts as shown in figure 5. Make sure split rings

are arranged so that the splits do not line up to form a leak path. Then slide the stack into the packing box as far as

will go while being careful to avoid trapping air among the rings.

2. Install the studs, packing follower, and nuts.

CAUTION

To prevent possible product damage or leakage, make sure the valve plug remains in the closed position when installing

new packing parts.

3. Make sure the valve plug is in the closed position when installing new packing parts.

4. Insert a screw driver, pry bar, or similar tool between the lower ear of the plug and the valve body (see figure 6). Use

the pry to move the plug tightly against the thrust washer and bearing on the actuator side of the valve. Keep the

valve plug in that position until you have completed the packing installation.

5. Tighten packing flange nuts enough to stop leakage under normal conditions.

6. Mount the actuator while referring to the actuator mounting procedures of the actuator instruction manual. You

must complete the Adjusting Actuator Travel procedure in this manual before installing the valve in the pipeline,

due to the measurements that must be made during the actuator adjustment process.

Instruction Manual

D100423X012

V500 Valve

July 2017

7. When the control valve is being put back into operation, check the packing follower for leakage, and retighten the

packing nuts as necessary.

Replacing Retainer, Seat Ring, and Face Seals

This procedure is to be performed if the control valve is not shutting off properly, if the port diameter is to be changed

by installing a different seat ring, or if seat ring inspection is necessary. The actuator and valve (key 1) must be

removed from the pipeline; however, the actuator may remain mounted during this procedure.

A retainer tool is required to remove the retainer (key 5), seat ring (key 4), and face seals (key 8). If specifically ordered,

a tool is supplied with the valve; a tool can also be ordered individually. If desired, a tool can be machined using the

dimensions shown in figure 7.

During assembly, handle the retainer, seat ring, and face seals carefully. Critical areas that must be protected are the

threads and inner surface of the retainer (key 5), the sealing surfaces of the face seals (key 8), the face seal grooves in

the seat ring (key 4), the shutoff surface of the seat ring, and the face seal surface in the valve body (key 1).

A new retainer gasket (key 11) is required whenever the retainer (key 5) is removed. Other parts in good condition can

be reused.

Disassembly of Retainer, Seat Ring, and Face Seals

Key numbers are shown in figures 11 and 13 unless otherwise noted.

1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the

process media from both sides of the valve. If using a power actuator, also shut off all pressure lines to the power

actuator, release all pressure from the actuator. Use lock‐out procedures to be sure that the above measures stay in

effect while you work on the equipment.

2. Remove line bolting. Then, remove the control valve from the pipeline and place the valve on a flat surface with the

retainer (key 5) facing up.

3. Rotate the valve shaft (key 3) to move the valve plug (key 2) into the open position.

Note

The retainer (key 5) was installed at the factory using the torque listed in figure 8.

4. Remove the retainer by engaging the retainer tool, attaching an impact wrench or other suitable tool, and

unscrewing the retainer. Inspect the retainer.

CAUTION

Place the retainer on a protected, flat surface where the threads and inner surface will not be contaminated or damaged.

5. Remove the retainer gasket (key 11). Inspect the gasket surfaces on the valve body (key 1).

6. Lift out the seat ring (key 4) and both face seals (key 8). Inspect the parts and place them on a flat, protected

surface.

7. Inspect the shutoff surface of the valve plug. If it is worn, nicked, or scratched, proceed to the Replacing Valve Plug,

Shaft, and Bearings procedure. If the parts are in good shape and do not require maintenance, continue to the

Assembly procedure.

Table des matières

Autres manuels Emerson Unité de contrôle

Emerson

Emerson Fisher Type H800 Manuel utilisateur

Emerson

Emerson Fisher TBX Manuel utilisateur

Emerson

Emerson Anderson Greenwood 500 Series Manuel utilisateur

Emerson

Emerson Fisher ACE95 Series Manuel utilisateur

Emerson

Emerson Fisher V280 Manuel utilisateur

Emerson

Emerson Bettis OM13-SCE300 Manuel utilisateur

Emerson

Emerson TARTARINI BM5A Manuel utilisateur

Emerson

Emerson Rosemount RM5800 Manuel utilisateur

Emerson

Emerson ASCO 290 Series Manuel utilisateur

Emerson

Emerson KTM Series Manuel

Emerson

Emerson VA001-102-01 Mode d’emploi

Emerson

Emerson Sempell PSRV VS99 Manuel utilisateur

Emerson

Emerson Yarway 7100 Series Manuel utilisateur

Emerson

Emerson Neotecha Instructions d'installation et d'utilisation

Emerson

Emerson Tartarini BM5 Series Manuel utilisateur

Emerson

Emerson YARWA 151 Series Manuel utilisateur

Emerson

Emerson Fisherr D2 FloPro Manuel utilisateur

Emerson

Emerson QC54 FOUNDATION Manuel utilisateur

Emerson

Emerson YARWAY 516 Series Manuel

Emerson

Emerson Alco Controls TIH Series Manuel utilisateur

Emerson

Emerson E5 Manuel utilisateur

Emerson

Emerson KEYSTONE DUBEX Manuel utilisateur

Emerson

Emerson Fisher NPS 8 CHP Manuel utilisateur

Emerson

Emerson Bettis OM3 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur