ekwb EK-PRO GPU WB RTX A100 80GB Manuel utilisateur
USER GUIDE
GPU WATER BLOCK
EK-PRO
GPU WB RTX A100 80GB
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6
PREPARING YOUR GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 8
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE WATER BLOCK 9
CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES 11
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 11
TESTING THE LOOP 12
SUPPORT AND SERVICE 13
SOCIAL MEDIA 13
- 4 -
EK-PLUG G1/4 (2x)
3830046999153
Allen Key 2.5mm (1x) 8902
Allen Key 2mm (1x) 8901
120 mm
24 mm
BOX CONTENTS
Nut M2.5 (6x) 8506
Screw M2.5x4 ax1 (16x)
9047
EK-Loop Multi Allen Key (1x)
3830046996213
Screw M2.5x8 ax1 (2x) 8104A
Screw M3x6 DIN 7991 (2x) 9029
Thermal PAD F 1.0mm - (120x16mm)
(2x) 3830046996732
Screw M3x4 DIN7985 (2x)
8123
EK-TIM Ectotherm (1g) (1x)
3830046998446
Screw M3x6 ISO 14581 - TX-INOX
(2x) 103090
Screw UNC 6/32x5 (1x) 8483
EK-Pro GPU WB RTX A100 Ni +Inox (1x)
3831109847961
Washer POLYAMID M2.5 0.7mm
with self-adhesive tape (2x) 8627
Thermal PAD G 1.0mm - (120x24mm)
(2x) 3830046996770
120 mm
16 mm
Washer
POLYAMID M2.5 0.5mm
(16x) 8623
Screw M2.5x6 ax1 (13x)
9058
- 5 -
WATER BLOCK DIMENSIONS
267 mm
278.4 mm
97 mm
104.3 mm
134.2 mm
134.2 mm
97 mm
19.5 mm
14 mm
46.5 mm
75.5 mm
- 6 -
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS
Position EAN Description Quantity
1105670
055 - alu - RTX A100 80GB coldplate
1
2105671
055 - top acetal - A100 80GB insert
2
35028
OR 5 x 1.5
2
45196
OR 180 x 2
1
5103090
Screw M3 x 6 ISO 14581 - TX-INOX
19
6100845
Distancer M4/M2.5 x 2.5 - HEX
8
7103767
top acetal - FC terminal Direct (2x G1-4)
1
8103713
054 - metal power adapter
1
9103705
055 - metal - RTX A100 Pro Top Inox
1
10 100006
Screw M4 x 27 DIN7984
3
11 5155
OR 15 x 1 EPDM50 (FC Terminal)
2
12 102489
Medenina - Pro GPU Bracket standoff M4-6/32
1
13 8625
Washer POLYAMID M3 0.5 mm self-adhesive
2
14 9029
Screw M3 x 6 DIN7991 - INOX
2
11
3
4
18
2
12
9
7
5
13
14
6
10
- 7 -
PREPARING YOUR GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove
the stock cooler. Do not forget to unplug all the LED and fan
connectors. Pay attention to the following steps in order to install
the EK-Pro GPU RTX A100 water block onto the graphics card.
STEP 2
CLEANING THE PCB
Wipe off the remains of the original thermal compound using a
nonabrasive cloth or Q-tip, as shown in the sample image, until the
components and circuit board are completely clean. EK recommends
the use of denatured alcohol for removing TIM leftovers. After that,
remove all remaining stock thermal pads from the PCB.
STEP 2
- 8 -
CUTTING AND PLACING THERMAL PADS
Your GPU water block comes with un-cuted thermal pads to cover all
the VRM components, such as COILs, MOSFETs, and drivers. Please
use 1,0mm thick thermal pads which should be placed on the water
block, as illustrated below. EK made sure to provide you with more
than an adequate quantity of thermal pads to complete this Step.
You must remove the protective foil from both sides of the
thermal pad before installation.
Thermal Pad F 1.0 mm
Thermal Grease
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the GPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
APPLYING THERMAL COMPOUND
For this Step, you will need:
- 9 -
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks. Carefully
position the water block with preinstalled standoffs on the graphics
card. During this process, make sure you have aligned mounting
holes of the PCB with holes of the water block.
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1
For this Step, you will need:
M 2.5 PVC Washer
(8 pcs)
M2.5 x 4 AX1
Screw (8 pcs)
4 mm
STEP 2
STEP 2
ATTACHING THE WATER BLOCK
Use eight (8) M2.5 x 4 AX1 screws and M2.5 PVC washers.
Tighten the screws evenly using the Phillips head screwdriver. EK
recommends you start tightening the screws around the GPU core
first and then continuing outward to prevent damage to the GPU.
The screws must be present on the places marked below:
Phillips Head
Screwdriver
- 10 -
STEP 4bSTEP 4a
STEP 4
Secure power cable with mounting it into included inox power
adapter.
STEP 4a
Stick the two included plastics pads (M3) on to inox power addapter
as shown on picture.
STEP 4b
Insert 8-pin power connector in to the inox adapter. Pads on the
power adapter must be alligned with openings in inox power adapter.
Pay attention to the orietation of the latch on connector.
For this Step, you will need:
M3x6
SCREW
Screw M3x6 DIN 7991
(2x) 9029
Allen Key 2mm
(1x) 8901
STEP 4c
STEP 4c
Fasten a inox power adapter to the water block with two M3x6
screws. The power cables is needed to be twistand bend a bit in
order to fit them in.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels ekwb Matériel informatique
ekwb
ekwb EK-FB ASUS Strix X299-E RGB Monoblock Manuel utilisateur
ekwb
ekwb EK-FC780 GTX Ti Manuel
ekwb
ekwb EK-FCQ6000 Manuel
ekwb
ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur
ekwb
ekwb EK-Vector RTX Aorus 2080Ti Manuel utilisateur
ekwb
ekwb EK-PRO GPU WB RTX A4090 Manuel utilisateur
ekwb
ekwb EK Manuel utilisateur
ekwb
ekwb EK-FC980 GTX Ti XG Manuel utilisateur
ekwb
ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Manuel utilisateur
ekwb
ekwb EK-PRO GPU WB AMP/Trinity RTX 4090 - Ni +... Manuel utilisateur
ekwb
ekwb EK-FB KIT ASUS R5E Mode d’emploi
ekwb
ekwb EK-PRO GPU WB RTX 30x0 Manuel utilisateur
ekwb
ekwb EK-FC 780 GTX DCII Original CSQ Manuel
ekwb
ekwb EK-FB EVGA X58 LE Mode d’emploi
ekwb
ekwb EK-Nucleus AIO CR360 Vision D-RGB Manuel utilisateur
ekwb
ekwb EK-FC790 Mode d’emploi
ekwb
ekwb EK-FC970 GTX Manuel
ekwb
ekwb EK-Vector RTX 2080 FTW3 Manuel utilisateur
ekwb
ekwb EK-FB GA Z87X-OC Force Mode d’emploi
ekwb
ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
