Ekwb EK-FB EVGA X58 LE Mode d’emploi

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sample photo of EVGA X58 LE PCB design

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 6 screws on the back of

the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: lightly coat the Northbridge with for example

Céramique™ thermal compound. Follow this link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en for

detailed instructions. EKWB recommends non-conductive MX-2, which should

be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. One thermal pad (90x15x1 mm) and 2 (30x25x0,5) thermal

pads are enclosed with your water block. Please cut thermal pads as shown bellow.

(WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow. (PLEASE REMOVE FOIL OF THERMAL PADS

PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB EVGA X58 LE water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon7thofAugust,2009.

Southbridge

Northbridge

Mosfets

CPUsocket

18x4x0,5mm

75x7,5x1mm

25x25x0,5mm

18x4x1mm

12x4x0,5mm

12x4x1mm

Applythermalgreasehere.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes and place acetal standoffs (thickness 2,5 mm) so the holes are concentric.

Thermal paste provides enough adhesive force for standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water block or

vice versa and attach it with enclosed screws as shown. Make sure that mounting

holes are aligned.

STEP 4: ATTACHING BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

For

perfect thermal contact, the block does not use a spring mounting system; therefore when attaching be very careful to tighten all screws equally.

Tightening the screws beginning in the center of the block near the Northbridge, and continue evenly outwards. Do not use too much pressure

screws (be very careful around Southbridge and use small amount of tightening force, since block has no standoffs. EKWB recommends

tightening screws around Southbridge in the end.), because motherboard might

bend and either cause bad contact with water block, or break

a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

STEP 5: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary.

STEP 6: POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

1.Screw in fittings as shown in photo, attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. The EK-FB EVGA X58 LE series are usually sold with

high flow fittings. To ensure that the tubes are securely attached to the barb fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always

recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 6 screws M2,5x6 DIN7985

Please use the enclosed insulating

washers on all M2,5x6mm screws.

Fitting/barb

Spacer

Washer

Autres manuels ekwb Matériel informatique

ekwb

ekwb EK-FC1070 GTX Manuel utilisateur

ekwb

ekwb EK-FC780 GTX Ti Manuel

ekwb

ekwb EK-FC780 GTX Jetstream Manuel

ekwb

ekwb EK-FCS10000 Manuel

ekwb

ekwb EK-FC780 GTX Classy Rev.2.0 Backplate Mode d’emploi

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Mode d’emploi

ekwb

ekwb EK-FC690 GTX Backplate Manuel

ekwb

ekwb EK-Quantum Vector XC3 RTX 3080 D-RGB Manuel utilisateur

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

ekwb

ekwb EK-FB ASUS M5E Mode d’emploi

ekwb

ekwb EK-Supreme HF Mode d’emploi

ekwb

ekwb EK-FB GA 990FXA-UD7 Manuel

ekwb

ekwb EK-FC780 GTX Ti Matrix Manuel

ekwb

ekwb EK-FB ASUS PRIME X299 RGB Monoblock Manuel utilisateur

ekwb

ekwb EK-Quantum Velocity 2 Manuel utilisateur

ekwb

ekwb EK-FB KIT ASUS R5-E10 Mode d’emploi

ekwb

ekwb EK-FB ASUS C6H Monoblock Manuel utilisateur

ekwb

ekwb EK-FC7970 Manuel

ekwb

ekwb ASUS Z9PE-D8 Manuel utilisateur

ekwb

ekwb EK-FCW8100 Mode d’emploi

ekwb

ekwb EK-FC980 GTX Ti Strix Manuel

ekwb

ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Manuel utilisateur

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuel utilisateur

ekwb

ekwb EK-FC R9-390X TF5 Mode d’emploi

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

ekwb EK-FB EVGA X58 LE Mode d’emploi

Manuels Matériel informatique populaires d'autres marques