ECS K7SOM+ Manuel utilisateur

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 7.5a

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard

Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard

Describes installation of mainboard

components.

Go to ⇒page 7

Chapter 3

Using BIOS

Provides information on using the BIOS

Setup Utility.

Go to ⇒page 23

Chapter 4

Using the Mainboard Software

Describes the mainboard software.

Go to ⇒page 35

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction.................................................................................................1

Checklist.....................................................................................................1

Standard Items................................................................................................. 1

Features .....................................................................................................2

Choosing a Computer Case .......................................................................4

Mainboard Components .............................................................................5

CHAPTER 2 7

Installing the Mainboard 7

Safety Precautions......................................................................................7

Quick Guide................................................................................................7

Installing the Mainboard in a Case..............................................................8

Checking Jumper Settings..........................................................................8

Setting Jumpers ............................................................................................... 8

Checking Jumper Settings............................................................................... 9

Jumper Settings ............................................................................................... 9

Connecting Case Components.................................................................10

The SW1 Connector.......................................................................................11

Installing Hardware...................................................................................12

Installing the Processor.................................................................................. 12

Installing Memory Modules .......................................................................... 14

Installing a Hard Disk Drive/CD-ROM......................................................... 15

Installing a Floppy Diskette Drive................................................................. 17

Installing Add-on Cards................................................................................. 17

Connecting Optional Devices........................................................................ 19

Connecting I/O Devices............................................................................21

CHAPTER 3 23

Using BIOS 23

About the Setup Utility..............................................................................23

The Standard Configuration .......................................................................... 23

Running the Setup Utility.............................................................................. 24

Using BIOS...............................................................................................24

Standard CMOS Features.............................................................................. 25

Advanced Setup Page.................................................................................... 26

Power Management Setup Page .................................................................... 28

PCI / Plug and Play Setup.............................................................................. 29

Load Optimal Settings................................................................................... 30

Load Best Performance Settings.................................................................... 30

iii

Features Setup Page....................................................................................... 30

CPU PnP Setup Page..................................................................................... 32

Hardware Monitor Page................................................................................. 33

Change Password........................................................................................... 34

Change or Remove the Password .................................................................. 34

Exit................................................................................................................ 34

CHAPTER 4 35

Using the Mainboard Software 35

About the Software CD-ROM ...................................................................35

Auto-installing under Windows 98/ME/2000/XP .......................................35

Running Setup............................................................................................... 36

Manual Installation....................................................................................38

Utility Software Reference ........................................................................38

Introducing the Mainboard

Thank you choosing the K7SOM+ mainboard. This mainboard has a Socket-A

support for the AMD K7 processors. The Socket-A processor’s front-side bus

speed is 266MHz.

This mainboard integrates the SiS740 Northbridge and SiS962L Southbridge

chipsets that support DDR 266MHz, Ultra DMA 33/66/100/133 function and

remarkably high system performance under all types of system operations.

The mainboard supports the built-in AC97 Codec, two 32-bit PCI slots, one

CNR (Communications and Networking Riser) slot, and a built-in

10BaseT/100BaseTX Network Interface (optional).

This mainboard has the embedded 256-bit 3D AGP Graphics Accelerator with

64MB frame buffer, supporting AGP 4X 266MHz mode up to 1GB/s bandwidth,

which provides a direct connection between the graphics sub-system and

memory so that the graphics do not have to compete for processor time with

other devices on the PCI bus. The mainboard supports built-in USB 2.0 pro-

viding higher bandwidth implements Universal Serial Bus Specification

Revision 2.0 and is compliant with UHCI 1.1 and EHCI 0.95.

There is a full set of I/O ports including two PS/2 ports for mouse and key-

board, one serial port, one parallel port, one VGA port and maximum six

USB2.0 ports– four back-panel ports and onboard USB header USB2 provid-

ing two extra ports by connecting the Extended USB Module to the mainboard.

The board is Micro ATX size and has power connectors for an ATX power

supply.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• One diskette drive ribbon cable (optional)

• One IDE drive ribbon cable

• Software support CD

• The User’s Manual

Processor • Supports Socket-462 processor

• Supports AMD Athlon XP/Athlon/Duron processors

• Supports 266 MHz Front-Side Bus

Chipset The SiS740 Northbridge and SiS962L Southbridge in this

chipset in accordance with an innovative and scalable

architecture with proven reliability and performance. A few of

the chipset’s advanced features are:

• Integrate a high performance and high quality 3D/2D

Graphical Accelerator, Video Accelerator and Motion

Compensation MPEG1/MPRII Video Decoder

• Integrate a high performance 2.1GB/s DDR266 Memory

controller to sustain the bandwidth demand from the inte-

grated GUI, host processor, as well as the multi I/O

masters

• Integrate one Universal Serial Bus 2.0 Host Controllers,

the Audio Controller with AC97 Interface, the Ethernet

MAC Controller w/ standard MII interface, three Universal

Serial Bus 1.1 Host Controllers, the IDE Master/Slave

controllers, and SiS MuTIOL technology

Memory • Two 184-pin DIMM sockets for DDR memory modules

• Support DDR 266MHz memory bus

• Maximum installed memory is 1GB

VGA • Embeded 256-bit 3D AGP Graphics Accelerator with

64MB frame buffer

• Supports AGP 4X 266 MHz mode up to 1GB/s bandwidth

• Supports 333MHz true-colorm RAMDAC, resolution up to

2048 x 1536 x 16 bpp NI

• Supports AGP Rev. 2.0 Spec. Compliant

Expansion Slots • One CNR (Communications and Networking Riser) slot

• Two 32-bit PCI slots for PCI 2.2-compliant bus interface

Onboard IDE

channels

• Primary and Secondary PCI IDE channels

• Support for PIO (programmable input/output) modes

• Support for Multiword DMA modes

• Support for Bus Mastering and Ultra DMA ATA

33/66/100/133 modes

Power

Supply and

Power

Management

• ATX power supply connector

• Meets ACPI 1.0b and APM 1.2 requirements, keyboard

power on/off

AC’97 Audio

Codec

• Compliant with AC’97 2.2 specification

• Full-duplex Codec with independent and variable sam-

pling rate

• Earphone Buffer Built-In, SNR up to 90db

• 4Ch DAC, support 4-channel speak-out

• Advanced power management support

Onboard I/O

Ports The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One VGA port

• One parallel port

• Six USB2.0 ports (four back-panel ports, onboard USB

header providing two extra ports)

• Audio jacks for microphone, line-in and line-out

Built-in Ethernet

LAN (optional)

• 10Base-T/100Base-TX Physical Layer Solution

• Dual Speed – 100/10 Mbps

• MII Interface to Ethernet Controller/Configuration & Status

• Auto Negotiation: 10/100, Full/Half Duplex

• Meet All Applicable IEEE802.3, 10Base-T and 100Base-

TX Standards

USB 2.0 • Compliant with Universal Serial Bus Specification Revi-

sion 2.0

• Compliant with Intel’s Enhanced Host Controller

Interface Specification Revision 0.95

• Compliant with Universal Host Controller Interface

Specification Revision 1.1

• PCI multi-function device consists of two UHCI Host

Controller cores for full-/low-speed signaling and one

EHCI Host Controller core for high-speed signaling

• Root hub consists 4 downstream facing ports with

integrated physical layer transceivers shared by UHCI

and EHCI Host Controller

• Support PCI-Bus Power Management Interface

Specification release 1.1

• Legacy support for all downstream facing ports

BIOS Firmware This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

• Hard drives, diskette drives, and peripherals

• Power management

• CPU parameters and memory timing

• Hardware monitoring parameters

The firmware can also be used to set parameters for different

processor clock speeds.

Some hardware specifications and software items are subject to change

without prior notice.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the micro-ATX system case. Some features on

the mainboard are implemented by cabling connectors on the mainboard to

indicators and switches on the system case. Ensure that your case supports

all the features required. The mainboard can support one floppy diskette drive

and four enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has a micro-ATX form factor of 24.4 x 19 cm. Choose a case

that accommodates this form factor.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Table of Mainboard Components

Label Component

ATX1 Standard 20-pin ATX power connector

AUDIO1 Front panel MIC/Speaker Out header

BAT1 Three volt realtime clock battery

CD1 CD-in connector

CNR1 Communications Networking Riser slot

CPUFAN1 CPU cooling fan

CPU Socket Socket A for AMD Athlon/Duron CPUs

DDR1 ~ DDR2 Two 184-pin DDR DIMM sockets

FDC1 Floppy disk drive connector

IDE1 Primary IDE channel

IDE2 Secondary IDE channel

IR1 Infrared cable header

JP1 Clear CMOS jumper

JP2 USB card reader connector

PCI1 ~ PCI2 Two 32-bit add-on card slots

PWRFAN1 Power fan connector

SPK1 Speaker connector

SW1 Panel connector for case switches and LEDs

SYSFAN1 System cooling fan

USB2 Connector for front panel USB ports

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Table des matières

Autres manuels ECS Carte mère

ECS

ECS NFORCE3-A Manuel utilisateur

ECS

ECS L7VTA2 Manuel utilisateur

ECS

ECS 946GZT-M2 Manuel utilisateur

ECS

ECS 945PT-A2/1333 Manuel utilisateur

ECS

ECS B85H3-M7 Manuel utilisateur

ECS

ECS B85H3-A3 Manuel utilisateur

ECS

ECS L4S5A Manuel utilisateur

ECS

ECS K7S5A Manuel utilisateur

ECS

ECS Z77H2-A4 Manuel utilisateur

ECS

ECS P6VPA2 Manuel utilisateur

ECS

ECS A75F2-M2 Manuel utilisateur

ECS

ECS SF2/648FX Manuel utilisateur

ECS

ECS H81H3-M4 Manuel utilisateur

ECS

ECS P41G Series Manuel utilisateur

ECS

ECS 945GCT-M2 Manuel utilisateur

ECS

ECS H61H2-A Manuel utilisateur

ECS

ECS Z77H2-A2X Deluxe Manuel utilisateur

ECS

ECS G43T-WM Manuel utilisateur

ECS

ECS PN1 SLI2 Extreme Manuel utilisateur

ECS

ECS Durathon 2 H110M4-C23 Manuel utilisateur

ECS

ECS H61H2-M2 Manuel utilisateur

ECS

ECS P45T-A Manuel utilisateur

ECS

ECS 661FX-M Deluxe Manuel utilisateur

ECS

ECS P4VMM2 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur