ECS K7S7AG Manuel utilisateur

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 1.3b

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaim any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 7

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 25

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 37

Preface i

Features and Packing List Translations 錯誤! 尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction................................................................................................ 1

Checklist.................................................................................................... 1

Standard Items................................................................................................. 1

Features .................................................................................................... 2

Choosing a Computer Case....................................................................... 4

Mainboard Components ............................................................................ 5

CHAPTER 2 7

Installing the Mainboard 7

Safety Precautions..................................................................................... 7

Quick Guide............................................................................................... 7

Installing the Mainboard in a Case............................................................. 8

Checking Jumper Settings......................................................................... 8

Setting Jumpers ............................................................................................... 8

Checking Jumper Settings ............................................................................... 9

Jumper Settings ............................................................................................... 9

Connecting Case Components................................................................ 10

Front Panel Connector................................................................................... 12

Installing Hardware.................................................................................. 13

Installing the Processor.................................................................................. 13

Installing Memory Modules .......................................................................... 15

Installing a Hard Disk Drive/CD-ROM......................................................... 16

Installing a Floppy Diskette Drive................................................................. 18

Installing Add-on Cards................................................................................. 19

Connecting Optional Devices........................................................................ 20

Connecting I/O Devices........................................................................... 23

External Connector Color Coding................................................................. 24

CHAPTER 3 25

Using BIOS 25

About the Setup Utility............................................................................. 25

The Standard Configuration........................................................................... 25

Running the Setup Utility.............................................................................. 26

Using BIOS.............................................................................................. 27

Standard CMOS Setup Page.......................................................................... 27

Advanced Setup Page.................................................................................... 28

Power Management Setup Page .................................................................... 30

iii

PCI/Plug and Play Setup Page....................................................................... 31

Load Optimal Settings................................................................................... 32

Load Best Performance Settings.................................................................... 32

Features Setup Page....................................................................................... 32

CPU PnP Setup Page..................................................................................... 34

Hardware Monitor Page................................................................................. 35

Change Password........................................................................................... 36

Change or Remove the Password .................................................................. 36

Exit................................................................................................................ 36

CHAPTER 4 37

Using the Mainboard Software 37

About the Software CD-ROM................................................................... 37

Auto-installing under Windows 98/ME/2000/XP....................................... 37

Running Setup............................................................................................... 38

Manual Installation................................................................................... 40

Bundled Software Installation.................................................................. 40

Set Up the Audio System......................................................................... 40

Introducing the Mainboard

Thank you for choosing the K7S7AG mainboard. This mainboard has a

Socket-462 processor for the AMD K7 type of processors. You can install any

of these processors on the mainboard. This mainboard supports a system bus

speed of 333MHz.

With a measurement of 305 x 224 mm, this mainboard is built using the lead-

ing edge technology of SiS746 Northbridge along with SiS963 Southbridge

chipsets that supports built-in 6-channel speak-out AC97 Codec, 2 DDR400

(by overclocking) modules up to 2GB system memory.

It also supports the Xabre200 GPU, which integrates a 256-bit 3D/2D graphics

engines and motion compensation MPEG 1/MPEGII accelerator. In addition to

superior hardware capabilities, the mainboard has one CNR (Communications

and Networking Riser) slot to support Audio and Modem application, built-in

10BaseT/100Base TX Network Interface and an advanced full set of I/O ports

such as two PS/2 ports for mouse and keyboard, one serial port, one VGA

port, one parallel port, one IEEE port and six USB ports (USB 2.0) – consist-

ing of four back-panel ports and onboard USB header USB3 providing two

extra ports by connecting the Extended USB Module to the mainboard.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• One auto-install software support CD

• This user’s manual

Processor • Support Socket462 package CPU

• Supports AMD Athlon XP/Athlon/Duron processors

• Supports 333 MHz Front-Side Bus

Chipset The SiS746 Northbridge and SiS963 Southbridge chipsets are

based on an innovative and scalable architecture with proven

reliability and performance.

Memory • Two 184-pin DIMM slots for DDR memory modules

• Support DDR up to 400 MHz memory bus

• Maximum installed memory is 2GB

Note: You can work on DDR400 by overclocking,

but there is no guarantee that it will run

under normal operation.

Expansion Slots • One CNR (Communications and Networking Riser) slot to

insert special riser cards with Audio/Modem functionality

• Three 32-bit PCI slots for PCI 2.2-compliant bus interface

Onboard IDE

channels

• Primary and Secondary PCI IDE channels

• Support for PIO (programmable input/output) modes

• Support for Multiword DMA modes

• Support for Bus Mastering and Ultra DMA ATA 100/133

modes

Power Supply &

Power Manage-

ment

• ATX power supply connector

• Meets ACPI 1.0b and APM 1.2 requirements, keyboard

power on/off

• Supports RTC Alarm, Wake On Modem, AC97 Wake-Up

and USB Wake-Up

Integrated VGA

Specification

• GPU (Graphics Processing Unit)

− Xabre 200 AGP8X 256-bit GPU clock runs from

200MHz

• DISPLAY MEMORY

− Built-in 64MB DDR onboard runs from 400MHz

(DDR400)

• 3D ENGINE FEATURES

− Supports Direct 3D version 8.1; pixel shader

version 1.3

− Supports AGP 8X for texture/vertex fetch

− Built-in 32-bit floating point VLIW Geometry

Transform/Lighting (T/L) and triangle setup engine

− Built-in 4 pixel programmable rendering pipelines

and 8 texture units (4P8T)

− Supports up to 2048x2048 texture size

− Built-in hardware stereo auto rendering engine

− Supports 2X/4X full scene anti-aliasing

• 2D ENGINE FEATURES

− Built-in Direct Draw Accelerator

− MPEG-2 MP @ ML standards compliant

− Built-in motion compensation logig

− Supports up to 20Mbit/sec bit rate decoding

− Direct DVD to TV playback

− Supports single video windows with overlay

function

− Supports graphics and video overlay function

− Supports DVD sub-picture playback overlay

− Built-in independent Gamma correction RAM

• RESOLUTION

− Supports VESA standards super high resolution

graphics modes, up to 2048x1536x32 bpp

AC97 Audio

Codec

• 6-CH hardware architecture allows multi-channel south

bridge to playback 6CH audio

• IntelAC’97 (REV. 2.2) compatible, meeting Microsoft

PC2001 requirements

• Built-in earphone buffer and internal PLL, the latter saving

additionsl crystal

• Line-in/rear out share the same jack; Center/bass share

the MIC jack

• Digital S/PDIF OUT Support

• CRL3D: HRTF based BS3D compatible audio engine

Onboard I/O

Ports The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One VGA port

• One parallel port

• Two IEEE1394a port (one back-panel port, one onboard

IEEE1394a header)

• Six USB ports (four back-panel ports, onboard USB

headers providing two extra ports)— USB2.0

• Audio jacks for microphone, line-in and line-out

Hardware Moni-

toring Built-in hardware monitoring for CPU & System temperatures,

fan speeds and mainboard voltages.

Onboard Flash

ROM Supports Plug and Play configuration of peripheral devices

and expansion cards.

Built-in Ethernet

LAN

• 10Base-TX/100Base-T Physical Layer Solution

• Dual Speed – 100/10 Mbps

• MII Interface to Ethernet Controller/Configuration & Status

• Auto Negotiation: 10/100, Full/Half Duplex

• Meet All Applicable IEEE802.3, 10Base-T and 100Base-

TX Standards

USB 2.0 • Compliant with Universal Serial Bus Specification Revi-

sion 2.0

• Compliant with Intel’s Enhanced Host Controller

Interface Specification Revision 0.95

• Compliant with Universal Host Controller Interface

Specification Revision 1.1

• PCI multi-function device consists of two UHCI Host

Controller cores for full-/low-speed signaling and one

EHCI Host Controller core for high-speed signaling

• Root hub consists 4 downstream facing ports with

integrated physical layer transceivers shared by UHCI

and EHCI Host Controller

• Support PCI-Bus Power Management Interface

Specification release 1.1

• Legacy support for all downstream facing ports

IEEE 1394a • Fully supports provisions of IEEE1394-1995 for high-

performance serial bus and the P1394a draft 2.0 standard

• Provides two fully compliant cables ports at 100/200/400

Mbits/s and available with one or two ports

• Supports optional 1394 Annex J electrical isolation barrier

at PHY-link interface

• Supports power-down feature to conserve energy in bat-

tery powered application

• Node power-class information signaling for system power

management

BIOS

Firmware This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

Note: Some hardware specifications and software items are subject to change

without prior notice.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 305 x 224 mm. Choose a case that

accommodates this form factor.

Table of Mainboard Components

Label Component

ATXPW1 Standard power connector

AUDIO1 Front audio connector

BAT1 Three volt realtime clock battery

CD_IN1 Primary CD-in connector

CD_IN2 Secondary CD-in connector

CN1 Auxiliary power connector for Pentium 4 CPUs

CNR1 Communications Networking Riser slot

CPU SOCKET Socket 462 for AMD Athlon/Duron CPUs

CPUFAN1 Cooling fan for CPU

DDR1~ DDR2 Two 184-pin DDR SDRAM

FDC1 Floppy disk drive connector

IDE1 Primary IDE channel

IDE2 Secondary IDE channel

IR1 Infrared cable header

J1 Onboard LAN LED connector

JP2 IEEE 1394 header

JP3 Clear CMOS jumper

PCI1 ~ PCI3 Three 32-bit add-on card slots

SPK1 Internal speaker connector

SYSFAN1 System fan connector

SW1 Connector for case front panel switches and LED indicators

USB3 Front Panel USB headers

VGAFAN1 VGA cooling fan

WOM1 Wake On Modem header

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Table des matières

Autres manuels ECS Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur