ECS L4S5M Manuel utilisateur

Preface

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.1a

Disclaimer

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the contents

hereof and specifically disclaims any implied warranties of merchantability or fitness

for any particular purpose. The manufacturer reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's

manufacturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 6

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 24

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 45

iii

Preface i

Features and Packing List Translations 錯誤! 尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction............................................................................................................1

Checklist.................................................................................................................1

Standard Items ...................................................................................................1

Features..................................................................................................................2

Choosing a Computer Case................................................................................3

Mainboard Components.......................................................................................4

CHAPTER 2 6

Installing the Mainboard 6

Safety Precautions................................................................................................6

Quick Guide...........................................................................................................6

Installing the Mainboard in a Case.....................................................................7

Checking Jumper Settings...................................................................................7

Setting Jumpers .................................................................................................7

Checking Jumper Settings.................................................................................8

Jumper Settings.................................................................................................8

Connecting Case Components...........................................................................9

The Panel Connector.........................................................................................9

Installing Hardware.............................................................................................10

Installing the Processor...................................................................................10

InstallingMemoryModules............................................................................13

Installing a Hard Disk Drive/CD-ROM ..........................................................14

Installing a Floppy Diskette Drive ..................................................................15

InstallingAdd-on Cards..................................................................................16

Connecting Optional Devices..........................................................................18

ConnectingI/ODevices.....................................................................................22

External Connector Color Coding...................................................................23

CHAPTER 3 24

Using BIOS 24

About the Setup Utility........................................................................................24

The Standard Configuration............................................................................24

Entering the Setup Utility................................................................................25

Updating the BIOS..........................................................................................25

Using BIOS..........................................................................................................26

Standard CMOS Features................................................................................27

Advanced BIOS Setup Option........................................................................29

Advanced Chipset Features Option.................................................................31

IntegratedPeripheralsOption..........................................................................33

Power Management Setup Option...................................................................37

PNP/PCI Configuration Option.......................................................................41

Frequency/Voltage Control..............................................................................42

LoadFail-Safe Defaults Option......................................................................43

Load Optimized Defaults Option....................................................................43

Set Password Option.......................................................................................43

Save & Exit Setup Option...............................................................................44

Exit Without Saving........................................................................................44

CHAPTER 4 45

Using the Mainboard Software 45

About the Software CD-ROM............................................................................45

Auto-installing under Windows 98....................................................................45

Running Setup.................................................................................................46

Manual Installation..............................................................................................48

Utility Software Reference.................................................................................48

Award Flash Memory Utility...........................................................................48

PC-CILLIN......................................................................................................48

MediaRing Talk – Telephony Software...........................................................49

Super Voice –Fax/Modem Software...............................................................49

CD Ghost.........................................................................................................49

Recovery Genius.............................................................................................49

Language Genius.............................................................................................49

PageABC.........................................................................................................49

Introducing the Mainboard

Congratulations on purchasing the L4S5M mainboard. The L4S5M mainboard

is a Micro-ATX mainboard that uses a 4-layer printed circuit board and

measures 244 mm x 220 mm. The mainboard features a mPGA Socket 478

that accommodates Pentium 4 processors supporting frontside bus (FSB)

speeds up to 100 MHz.

The L4S5M incorporates the SiS645 chipset which combines support for the

new high-bandwidth Double Data Rate (DDR) SDRAM, and the AC 97 audio

codec.

Note: SDRAM provides 800 MBps or 1 GBpsdatatransferdependingonwhether

the bus is 100 MHz or 133 MHz. Double Data Rate SDRAM (DDR SDRAM)

doubles the rate to 1.6 GBps or 2.7 GBps by transferring data on both the

rising and falling edges of the clock. DDR SDRAM uses additional power and

ground lines and requires 184-pin DIMM modules rather than the 168-pin

DIMMs used by SDRAM.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•One auto-install software support CD

•One jumper cap for JP2

•One I/O panel

•One cooling fan retention module

•This user’s manual

Processor The L4S5M mainboard uses a micro PGA 478-pin socket that

has the following features:

•Supports 100 MHz frontside bus (FSB)

•Accommodates Pentium 4 processors

Chipset The SiS645 and SiS961 chipsets are based on an innovative

and scalable architecture with proven reliability and

performance. A few of the chipset’s advanced features are:

A low 2.5-volt DDR SDRAM power consumption which makes

it an excellent solution for notebooks and desktops with a

small footprint

Support for a 4xAGP interface providing vivid 3D graphics and

video performance

An ATA 100 interface on the chipset, which helps boost

system performance by providing a high-speed connection to

ATA 100 Hard Disk Drives, delivering maximum sustained data

transfer rates of 100 MB/sec

Built-in multithreaded I/O link used to enhance performance,

providing enough I/O bandwidth for throughput up to 1.2 GB/s

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Memory The mainboard supports DDR SDRAM. It accommodates two

unbuffered 2.5V 184-pin slots. Each slot supports up to 1 GB

with a total maximum capacity of 2 GB.

VGA The L4S5M includes a 4xAGP slot that provides four times the

bandwidth of the original AGP specification. AGP technology

provides a direct connection between the graphics sub-system

and the processor so that the graphics do not have to compete

for processor time with other devices on the PCI bus.

AC 97 Audio

Codec The AC 97 Audio codec is compliant with the AC 97 2.2

specification, and supports 18-bit ADC (Analog Digital

Converter) and DAC (Digital Analog Converter) resolution as

well as 18-bit stereo full-duplex codec with independent and

variable sampling rates. Further features include support for

four analog line-level stereo inputs.

Expansion

Options The mainboard comes with the following expansion options:

•Three 32-bit PCI slots

•One 4xAGP slot

•A Communications Network Riser (CNR) slot (AC97

interface only)

•Two IDE channels and a floppy disk drive interface

The L4S5M supports Ultra DMA bus mastering with transfer

rates of 33/66/100 MB/sec.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

•Two PS/2 ports for mouse and keyboard

•One serial port

•One parallel port

•One MIDI/game port

•Two USB ports

•One LAN port

•Audio jacks for microphone, line-in and line-out

BIOS

Firmware This mainboard uses Award BIOS that enables users to

configure many system features including the following:

•Power management

•Wake-up alarms

•CPU parameters

•CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard

complies with the specifications for the Micro-ATX system case. Some

features on the mainboard are implemented by cabling connectors on the

mainboard to indicators and switches on the system case. Ensure that your

case supports all the features required. The mainboard can support one or

two floppy diskette drives and four enhanced IDE drives. Ensure that your

case has sufficient power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has a Micro-ATX form factor of 244 x 220 mm. Choose a case

that accommodates this form factor.

CPUFAN1

CASFAN1

PWRFAN1

DIMM1

DIMM2

IDE2

ATX1

ATX2

CDIN1

AGP1

PCI1

PCI2

PCI3

CNR1

BT1

JP1

JP2

WOL1

LUSB2

LUSB1

WOM1

PANEL1

SPEAKER1

LSIR1

FLOPPY1

CDIN2 LMDN1

COM2

LAUDIO1

IDE1

LED1

AGP1

PCI1

PCI2

PCI3

CNR1 WOL1 SPEAKER1

IDE1IDE2

DIMM1 DIMM2

CPU SOCKET

CPUFAN1

CASFAN1

ATX1

CDIN1

CDIN2

JP1

JP2

LED1

J3 LSIR1

FLOPPY1

ATX2

LMDN1

LAUDIO1

PWRFAN1

LUSB1

LUSB2

RETENTIONMODULE

COM2

PANEL1

WOM1 BAT1

Table of Mainboard Components

Label Component

AGP1 Accelerated Graphics Port

ATX1 Auxiliary power connector for Pentium 4 CPUs

ATX2 Power connector

BAKFAN1 Case fan connector 2

BAT1 Three volt realtime clock battery

CDIN1 Primary CD-in connector

CDIN2 Secondary CD-in connector

CHSFAN1 Case fan connector 1

CNR1 Communications Networking Riser slot

COM2 Onboard serial port header COM2

CPU SOCKET Micro PGA 478-pin socket for Pentium 4 CPUs

CPUFAN1 Cooling fan for CPU

DIMM1, DIMM2 Two 184-pin DDR SDRAM

FLOPPY1 Floppy disk drive connector

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

J2 Smart I/O interface header

J3 Power switch header

JP1 Clear CMOS jumper

JP2 BIOS protection jumper

LAUDIO1 Front audio connector

LED11Memory module LED

LMDN1 Modem-in header

LPANEL1 Connector for case front panel switches and LED indicators

LSIR1 Infrared cable header

LUSB1 Front panel USB headers

LUSB2 Front panel USB headers

PCI1 ~ PCI3 Three 32-bit add-on card slots

SPEAKER1 Speaker connector

WOL1 Wake On LAN wakeup connector

WOM1 Wake On Modem wakeup connector

This concludes Chapter 1. The next chapter explains how to install the

mainboard.

1The red indicator LED1 turns on if your system is still powered, at which

time memory modules cannot be installed or uninstalled.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

•Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

•Discharge static electricity by touching the metal caseof a safely

grounded object before working on the mainboard.

•Leave components in the static-proof bags they came in.

•Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 4

Installing the Mainboard in a Case Go to page 7

Setting Jumpers Go to page 7

Installing Case Components Go to page 9

Installing the CPU Go to page 10

Installing Memory Go to page 13

Installing an HDD and CD-ROM Drive Go to page 14

Installing an FDD Go to page 15

Installing Add-on Cards Go to page 16

Connecting Options Go to page 18

Connecting Peripheral (I/O) Devices Go to page 22

Table des matières

Autres manuels ECS Carte mère

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur