Eaton I-on Compact Manuel utilisateur

i-on Compact

Quick Setup Guide

Introduction

This guide provides a quick overview of

how to set up standard features of an i-on

Compact control unit.

Note: Details of all features and options are

available in the

i-on Compact Engineering

Guide

, and

i-on Compact Admin & User

Manual

, which you can download from

www.touchpoint-online.com.

Step 1: Power-up the control unit

After installing all hardware (as described in the

Installation

Guide

1. Switch on the mains supply to the control unit.

2. Follow the on-screen prompts. When you see the following,

enter a four-digit installer access code of your choice, then

enter it again when prompted. DO NOT FORGET THIS CODE!

NEW INSTALLER CODE

( )

3. When you see the following, enter a four-digit access code

of your choice for User 1 (master user) , then enter it again

when prompted. DO NOT FORGET THIS CODE!

NEW USER 1 CODE

( )

4. The standby screen is displayed. For example:

i-on Compact

12:00 01/12/2017

i-on Compact

10:43 03/06/2017

Page 2

Step 2: Enter installer mode

Installer mode gives you access to

the installer options. To enter installer

mode:

1. Make sure the standby screen is

displayed (see the previous page).

2. Enter the installer code you

created.

3. If you are prompted for a user

code, enter that too.

4. The bottom line displays

Detectors/

Devices

, which is the first option in

the menu:

INSTALLER MENU

Detectors/Devices >

How to select options

To select an option, press uor n(on

the Navigation key) until the name of

the option you want is displayed, then

press .

Selecting an option may display a

menu of further options. For example,

selecting

Detectors/Devices

displays

the first option in the

Detectors/

Devices

menu (

Detectors

DETECTORS/DEVICES

Detectors

Press to exit a menu or to cancel an

action.

Some options require you to press 

or to change the setting.

Note: A menu map of all installer

options is available on page 6.

Step 3: Add door contacts

(DET-RDC) or PIRs (XCELRPT)

1. Open the cover of the door contact

or PIR and insert the battery.

2. Close the cover.

3. From the top level of the Installer

menu:

a. Select

Detectors/Devices

b. Select

Detectors

c. Select

Add/Del Detectors

d. Use uor n to choose a zone

number, then press (each

door contact and PIR needs

a different zone number). The

display shows:

Activate

detector tamper

4. Open the cover of the door contact

or PIR.

5. The display shows “Detector

assigned to Zone xxx” and the

signal strength (0-9). Each zone

represents one device.

6. Repeat the above steps for each

door contact and PIR.

Step 4: Add external radio

sirens (SDR-REXT-G2)

Please refer to the installation

instructions provided with the siren.

At the step where you need to teach

the control unit the siren’s identity:

1. Make sure that the batteries are

not connected.

2. From the top level of the Installer

menu:

a. Select

Detectors/Devices

b. Select

External Sirens

c. Select

Add/Del Siren

d. Select a siren number (each

siren needs a different number).

The display shows:

Activate

Siren Tamper

Page 3

3. Insert the batteries into the siren.

4. The display shows “Siren

assigned to Siren xx” and the

signal strength (0-9).

5. Continue to follow the siren

installation instructions.

Step 5: Congure the zones

Configure each zone (door contact

and PIR) as follows:

1. Select

Detectors/Devices

2. Select

Detectors

3. Select

Program Zones

4. Select the zone number to

configure.

5. Carry out steps 5a to 5c below.

Step 5a: Change the zone name

Changing the name of a zone to, for

example, “lobby” or “stairs” will

help you to identify the location of

the detector. After selecting the zone

number (as above):

1. Select

Name

The display shows the cursor

at the beginning of the bottom

line. If you press a key (0 to

9), the bottom line clears and

the character appears at the

beginning of the line.

2. Use the following keys:

• 1 to 9 to enter numbers and

text. Each key is labelled

to show the characters you

can enter using that key. For

example, press “2” to enter

A, B, C or 2. Press the key

one or more times to select

the character (for example,

press “2” twice to enter a B).

• 0 to enter a space or

character such as &, @ or /.

• # to change between capital

and lower-case letters.

• uor nto move the cursor

left or right.

• to delete a character.

Step 5b: Choose the zone type

The zone type defines how a

detector will react when activated.

After selecting the zone number:

1. Select

Type

2. Select a zone type. For a typical

domestic installation, only one

of the following three zone types

will be required (for details of

other zone types, visit www.

touchpoint-online.co.uk and

download the full Engineering

Guide).

• Final Exit — Usually for the

front door.

Select this if the zone is the

last detector activated on exit,

or the first activated on entry.

Zones of this type complete

the setting procedure, or start

the entry procedure.

• Entry Route — Usually for

the hallway.

Use this zone type for

detectors sited between

the Final Exit zone and the

control unit. If the entry/exit

timer is running when an

Entry Route zone is triggered,

no alarm occurs until the

entry/exit timer expires.

• Normal Alarm — For all other

rooms.

When triggered, a zone of

this type will start an alarm if

the system is set. This is the

default zone type for any new

radio detector that the control

unit learns.

Page 4

Step 5c: Choose the zone

attributes

Attributes define how a detector will

react under certain conditions.

After selecting the zone number:

1. Select

Attributes

2. If required, select one or more

attributes. For a typical domestic

installation, only one of the

following two attributes will be

required (for details of other

attributes, visit www.touchpoint-

online.co.uk and download the full

Engineering Guide).

• Part set B, C or D — For areas

that are occupied at night, such

as upstairs. Select this attribute

so that if a user selects Part Set

B, the control unit sets only

those zones that have the Part

Set B attribute set to “On”.

• Chime — Normally for

detectors used on front or

back doors. When enabled,

the system gives a non-alarm

chime when the zone is

triggered. The chime operates

only when the system is unset.

Step 6: Select the exit mode

The exit mode determines how the

system sets.

From the top level of the Installer

menu:

1. Select

Setting Options

2. Select

Full Set

(or

Part set B/C/D

3. Select

Exit mode

4. Select an exit mode:

• Timed Set — The system sets

after a delay. Use

Exit Time

(at

the same level in the menu as

Exit mode

) to specify the delay.

The control unit logs the start

of the timed exit.

• Final Door Set — The system

sets after closing a door fitted

with a Final Exit zone detector.

Once the door closes, the

system sets after the Settle

Time expires. Note that the exit

time does not expire with this

option. The control unit logs the

start of final door exit.

• Instant Set — The system sets

immediately and without any

setting tone.The control unit

and any internal radio sounders

give a confirmation tone when

the system is set.

• Silent Set — This is the same as

Timed Set, but there is no exit

tone. On entry, the control unit

and any internal radio sounders

give an entry tone.

Step 7: Add remote controls

(FOB-2W-4B)

Remote controls allow you to set and

unset the system from a distance.

From the unset state:

1. Press the menu key ( ).

2. Enter the user code you created

during the power-up procedure

(Step 1). This displays the User

menu (as documented in the

Admin & User Manual

3. Select

Users

4. To assign a remote control

(remote) to a new user, select

Add

User

and follow the prompts to:

a. Modify the default name

(optional).

b. Select a user type (usually

Normal User).

c. Specify an access code

(optional).

d. Assign a proximity tag. Press 

if there is no tag.

Page 5

e. Assign the remote (press any

button).

f. Assign a radio Hold Up Alarm

(HUA) Press both orange

buttons. Press if there is no

HUA.

5. To assign a remote to the master

user, select

Edit User

, then:

a. Select

User 001

b. Select

Remote

c. Press any button on the remote.

Step 8: Congure or disable

communications

You need to do one of the following:

•If you are connecting the control

unit to an Alarms Receiving Centre

(ARC), configure communications

as described in the

Engineering

Guide

•If you are not using an ARC,

disable communications as

follows. (If you do not do this,

the navigation key will remain

permanently red to indicate an

alert state.)

From the top level of the Installer

menu:

a. Select

Communications

b. Select

ARC Reporting

c. Select

Call Mode

d. Select

Disabled

e. If you select

Call Mode

again,

you will see a * before

Disabled

to indicate that this is the

selected option.

Basic configuration of the control unit

is now complete. Please refer to the

Engineering Guide

Admin & User

Manual

(which can be downloaded

from www.touchpoint-online.co.uk) if

you need further information.

Step 9: Congure

SecureConnect™

SecureConnect allows users to set

or unset the alarm system, switch

outputs on or off and perform other

functions from a mobile device. If

users require this feature, please

configure SecureConnect as described

in the SecureConnect Installer Guide

(which can be downloaded from www.

touchpoint-online.co.uk).

Page 6

Installer menu map

The following menu map shows all options in the Installer menu and their

locations. Please refer to the

Engineering Guide

for details of these options.

1 Detectors/Devices

Detectors Add/Del Detectors Zone nnn...

Delete all

Program Zones Zone 000...

Name

Type

Attributes

On-board Keypad Key A Name

Action

Key B Name

Action

Key C Name

Action

Key D Name

Action

ABCD Led

Audible Keys

Status fault

Status OK

Backlight Mode

Brightness

Radio Keypads i-rk01

Add/Del Radio Kpd

Edit Keypads Radio Kpd 01...

Name

Key A

Key B

Key C

Key D

External Sirens Add/Del Siren

Edit Siren Radio SRN 01...

Name

Internal Sounders Add/Del Sounder

Edit Sounder Int. SNDR 01...

Name

Volume

WAMs Add/Del WAM

Edit WAM

Page 7

Cameras IP Cam 1... Camera Triggers

Zone Follow

Zone Alarm

IP Address

HTTP Port Internal

2 Outputs

Radio outputs Add Outputs

Edit Outputs EDIT RADIO O/P 1...

Name

Type

Pulsed

Zones

Delay

On Time

3 Setting options

Full Set Name

Exit Mode

Settle Time

Exit Time

Entry Time

Siren Delay

Siren Time

Strobe on Set

Strobe on Unset

Part Set B/C/D

(displayed only if a zone

has the relevant part set

attribute set)

Name

Exit Mode

Settle Time

Exit Time

Entry Time

Alarm Response

Siren Delay

Siren Time

Pt.set Final Exit

Pt.set Entry Route

Strobe on Set

Strobe on Unset

Remote Set Exit Mode

Exit Time

Local Set on ER

Page 8

4 System Options

User Options User Access HUA keys active

Quick set

Quick omit

User code reqd

2 Way Replies

2W Set Instant

Tamper Omit

Silence Alerts

User Reset Zone alarms

Zone tampers

System tampers

CSID Code

Restore Defaults Staged defaults User

Zones

Radio Devices

Outputs

Setting Info

System Options

Communications

Factory defaults

Installer Options Installer Name

Installer Code

Keypad text

Confirmation Confirmation Mode DD243

BS8243

Basic

Confirmation time

Entry Alarm Delay

After Entry

Entry Keypad Lock

Sounder on

Siren on

Unconfirmed reset

Confirmed reset

HUA Response

HUA Confirm time

Tamp as Tamp-Only

Abort Time

Auto Rearm

Page 9

Hardware On-board Sounder Volume

A/C Fail Reporting

Mains Fail Delay

Ext DC Fail Reporting

Ext DC Fail Delay

GSM Antenna

Radio Options Supervision

Jamming

Remotes Remote needs Entry

Remote Entry PrtSt

Force Set

i-rk01 RKP needs Entry

RKP Entry PrtSt

Perimeter Options

(displayed only if there is a

zone of type Perimeter)

PZ Unset Response

PZ Set Response

PZ Reset Time

Date and Time Set Date & Time

SNTP Time Sync SNTP Enable

Sync on Startup

Sync Interval

Manual Sync

NTP Server Names

Updates Language

Panel Upgrade

Level 4 Update

5 Communications

Contacts Recipient A... Name

Tel No 1

Tel No 2

IP Address

ARC Reporting Call Mode

Telecoms Priority Panel Ethernet

PSTN

Recipients Tel. Recipient 1

Tel. Recipient 2

IP Recipient 1

IP Recipient 2

Account Numbers

Repor t Type

Fast Fmt channels

CID/SIA Events

Restorals

Page 10

Burg Comms Rearm

21CN FF Ack time

Send Tamp As Burg

Dynamic Test Call

Static Test Call

Unset Comms

SMS Outgoing Call Mode

Messages

Triggers

Destinations

PSTN SMS

Incoming Remote Control

Forwarding

Email Call Mode

Messages Home Message

Message 1-4

Triggers Message 1-4

Destinations Message 1-4

Server Server Name

Server Port Number

Account

Username

Password

SSL

Line Fail Response Panel Ethernet

PSTN

GSM

Line Fail Delay Panel Ethernet

PSTN

GSM

IP Options IP Address

IP Subnet Mask

Gateway IP Address

DNS IP Address

Web Server Status

IP Port Number

VKP Instant

Cloud Access

Net Speed

M2M Interface Status

IP Port Number

Dynamic DNS Status

Provider

Autres manuels pour i-on Compact

Table des matières

Autres manuels Eaton Unité de contrôle

Eaton

Eaton ELC-COPBDP Manuel utilisateur

Eaton

Eaton Form 4D Recloser Control Manuel utilisateur

Eaton

Eaton BBA 16 Series Manuel

Eaton

Eaton Power XL SmartWire-DT DX-NET-SWD Series Manuel utilisateur

Eaton

Eaton CEAG 3-PM-IO-INV Manuel de service

Eaton

Eaton PSG480B24RM Manuel utilisateur

Eaton

Eaton PowerXL DX-NET-DEVICENET Manuel utilisateur

Eaton

Eaton Scantronic i-on10 Manuel utilisateur

Eaton

Eaton ZB150 Series Manuel

Eaton

Eaton Vickers CG-03 Series Manuel utilisateur

Eaton

Eaton mMINT Guide de démarrage rapide

Eaton

Eaton ELC-GPXFERMOD Manuel utilisateur

Eaton

Eaton CEAG 3-PM-IO Manuel de service

Eaton

Eaton Vickers FCGT-02-A-11 Series Manuel utilisateur

Eaton

Eaton CI/E-PKZ01-X Series Manuel

Eaton

Eaton Cutler Hammer PanelMate ePro 7685 8 Series Manuel utilisateur

Eaton

Eaton XTPAXENCS65B Manuel

Eaton

Eaton PXS24 Series Manuel utilisateur

Eaton

Eaton Box 1 Manuel d'exploitation et d'entretien

Eaton

Eaton eNMC2 Manuel utilisateur

Eaton

Eaton ELC-COENETM Manuel utilisateur

Eaton

Eaton 5PX EBM 72V RT2U Manuel utilisateur

Eaton

Eaton COOPER POWER SERIES Manuel du propriétaire

Eaton

Eaton ESWV10401 Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur

Flyron

Flyron FN-BC04 Manuel utilisateur

Eaton i-on Compact Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques