Earth Way M20 Manuel utilisateur

Operation and Assembly Manual

for the

EarthWay M20 12-volt

ATV Broadcast Spreader

Pt. #52190

EarthWay

Electric Spreaders

Model M20

1. Always wear protective clothing, eyewear, and dust mask to prevent contact with chemicals and other materials

being applied with this machine.

2. Remove any material in the hopper before lifting or detaching this machine from the vehicle.

3. Care must be taken when lifting this machine so as not to cause personal injury or equipment damage. Never at-

tempt to install this machine to the vehicle alone. Recruit the help of someone to assist when attaching and de-

taching this machine from the vehicle.

4. Refer to the material packaging or the Material Safety Data Sheet for precautionary measures required when han-

dling materials to be applied.

5. Before attaching this machine, consideration must be given to the load capacity of the vehicle. Refer to the

owner’s manual of the vehicle for rated load capacity. Be sure to take into account the weight of this machine 20

lbs. and the weight of the material to be placed in the hopper when calculating the total load.

6. Keep hands away from any spinning object.

How to operate safely:

A. Read, understand, and follow all product label information provided on the material being applied.

B. An adjustable solid stop is provided that allows the operator to adjust to the desired opening position on

the rate setting control prior to operation of the vehicle. This allows repeatability to the stop without the

need to look at the control while operating the vehicle.

C. Establish the correct rate and then lock the stop in that position using the thumb wing nut on the setting

control.

ASSEMBLY INSTRUCTIONS 1. Attach frames to hopper as shown using (4) # 10 x 1-1/4” screws.

2. Position the rate control assembly to either frame rail based on if the spreader is

mounted to the front or the rear rack. If on front mount the control to the left rail, if

on the rear mount on the right rail.

WARRANTY

EARTHWAY guarantees this product to be free of defects in original workmanship

and materials for a period of 90 days from sale to the original user. If any defect

develops during this period EARTHWAY will repair or replace this product at no

charge provided the defect is not the result of mishandling or tampering and that this

product is received at the factory with shipping charges prepaid. For quicker service

you may call EARTHWAY at (574) 848-7491 or write and describe the nature of the

defect and we will send repair parts to you.

Due to the corrosive nature of most fertilizers and ice melters, EARTHWAY PROD-

UCTS, INC. makes no warranty or guarantee against corrosion failure on models

with plated steel or painted steel frames.

Clean and dry your spreader well after each use.

Warranty covers parts only, not labor charges to repair.

How to attach to yourATV:

Position the M20 centered on either the front or rear luggage rack on

your ATV. Next using the included “Double J-Bolts” connect the rear

cross bars to the luggage rack cross bar closest to the seat or handle-

bars. Using two “Double J-Bolts” attach the M20 to the luggage rack

securing it to the outer most rail on the luggage rack. Tighten all fasten-

ers and cut any excessive bolt lengths that extend beyond the nuts on the

“J-Bolts” and smooth if necessary.

Prior to each use and occasionally during times of extended use, inspect the mounting and spreader hardware for

loosening to ensure the rigidity of the mount. This is done by tightening any loose hardware either on the

Spreader or Luggage Rack mounts.

Connecting the Power

After your spreader is securely attached to your

ATV, connect the wiring harness to the spreader

motor, then to the battery. The motor is to rotate in a clockwise direction when properly con-

nected, if not reverse the battery connection wires from the spreader to ensure a clockwise when

looking in the hopper.

Secure all wires so that they will not become entangled with operator or machinery with proper wire

fastening straps.

If rate settings are not available use the following procedure to calculate the setting:

1. Determine how much material is to be applied per 1,000 sq/ft.

2. Measure off a distance of 50 feet, preferably on a paved surface such as a parking lot.

3. Weigh out enough of the material to be applied to fill the hopper at least half full. Record the weight for future use.

4. With the unit mounted on the vehicle and the hopper at least half full of the material to be spread, position the vehi-

cle far enough before the beginning of the 50 foot test area so that the vehicle will achieve the desired speed before

you reach the starting line.

5. Set the rate setting stop at a position that you feel would be an appropriate setting.

6. Start the vehicle in motion and as you cross the starting line (of the 50 feet) move the rate lever to the open position

against the stop. Take care to be aware of what is going on around you maintaining control of the vehicle.

7. Continue from the starting line with the unit spreading the material. As you cross the finish line move the rate lever

to the closed position.

8. Stop the vehicle and note the width of the spread path that was just completed.

9. Return to the start point and empty the remaining material from the hopper into your weighing container and re-

weigh.

Mounting

locations

EarthWay

Electric Spreaders

Rate Setting Worksheet

Desired Application Rate (lbs/1,000 sq ft) _____________

To determine the desired application rate divide the area (sq ft) the bag should cover by the weight of the bag, then multiply by

1,000. (example: 5000 sq ft / 25 lbs = .005 x 1,000 = 5)

___________Weight of Material Placed in Hopper

-__________Weight of Material Left in Hopper

=__________Weight of Material Used

50 Length of Test Area

x______ Width of Spread Area

=_______Total Spread Area

Divide the Weight of Material Used by the Total Spread Area =_________lbs\sq ft

Multiply the lbs\sq ft times 1,000 =________lbs\1,000 sq ft

Compare the results of your test to the desired application rate.

Adjust the rate setting stop accordingly and run through the test again.

Repeat this process until you have achieved the desired application rate.

The settings furnished on the Rate Setting Chart are intended as a guide only. Variations in physical characteristics of

material applied, brisk walking speed (3 mph.), and roughness of ground surface may require slightly different spreader

settings. Due to the above conditions, EARTHWAY PRODUCTS INC. makes no warranty as to the uniformity of

coverage actually obtained from the setting listed.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct from the

manufacturer, EARTHWAY PRODUCTS, INC.

Be sure to give the following information when ordering.

1.Model Number

2.Part Number

3.Part Description

Call (574)848-7491 or write for current prices.

EarthWay

Products, Inc.

P.O. Box 547

Bristol, Indiana 46507

(574) 848-7491 or 800-294-0671

www.earthway.com

N/A fasteners are available at any local hardware store.

Key # Part # Description Key # Part # Description

1 77003 Rain Cover 12 60431 Wire & Housing Assembly

2 60511 Wire Harness Assembly 13 N/A 1/4-20 X 1-3/4" FHPMS

3 60323 Motor Support Assembly 14 N/A 1/4-20 X 1-1/4" FHPMS

4 77101 Electric Motor 15 25116 Frame

5 60322 HopperAssembly Includes key #20& #19 16 43050 J-Bolt Bracket

6 44287 J-Bolt 17 N/A #10 X 1-1/4" Screw

7 12125 Lever 18 12318 Lower Housing Clip

8 60432 Gauge & Housing Assembly 19 12221 Shut Off Plate

9 60027 1/4-20 Wing Nut 20 N/A #8 X 3/8" Screw

10 N/A 1/4-20 HexNut 21 12109 Impeller

11 12319 Upper Housing Clip 22 N/A 1/8" X 1-1/4" Cotter Pin

38156 Hardware Package

EarthWay Products, Inc.

P.O. Box 547

Bristol, Indiana 46507

USA

EC DECLARATION OF CONFORMITY

(Machinery Directive & Electromagnetic Compatibility Directives)

Herewith we declare that the machinery described below is in accordance with the relevant

health and safety requirements of the EC Council Directives concerned with Machinery and

Electromagnetic Compatibility. No alterations are to be made to the machine without prior con-

sultation and approval of EarthWay Products, Inc. otherwise the Declaration may become inva-

lid. This equipment must be commissioned, used and maintained strictly in accordance with the

operating and maintenance instructions issued with the machine. Operators must be trained in

accordance with the recommendations given in the operating and maintenance instructions

issued with the machine.

Description of Machine: EarthWay M20 ATV 12-volt Broadcast Spreader

Serial Number: AS STAMPED ON MACHINE

Date of Supply: AS INVOICED DATE

Relevant EC Council Directives:

Machine Directives 89/392/EEC and subsequent amendments.

Electromagnetic compatibility Directive 89/336/EEC and subsequent amendments.

Issued by: Jeffrey Kendall on behalf of EarthWay Products, Inc.

Signed by:

Date: 29 September 2005

Position of Signatory: Vice President

DO NOT RETURN TO DEALER FOR REPAIR

EARTHWAY PRODUCTS, INC.

1009 Maple Street

P.O. Box 547

Bristol, IN 46507

FOR YOUR RECORDS

Date Purchased:

Store Name:

Table des matières

Autres manuels Earth Way Épandeur

Earth Way

Earth Way 2170 Manuel utilisateur

Earth Way

Earth Way 2170T Manuel utilisateur

Earth Way

Earth Way 2600A-Plus Estate Manuel utilisateur

Earth Way

Earth Way 2050TP Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way 2030 Manuel utilisateur

Earth Way

Earth Way 7350SU Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED GT 3100 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way 2170T Tow Manuel utilisateur

Earth Way

Earth Way 2050T Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C22HD Manuel utilisateur

Earth Way

Earth Way Ev-N-SprEd 2030 Series Manuel utilisateur

Earth Way

Earth Way M80 Manuel utilisateur

Earth Way

Earth Way Ev-N-Spred M24SSD Series Manuel utilisateur

Earth Way

Earth Way 2100P Estate Manuel utilisateur

Earth Way

Earth Way 2050TP Manuel utilisateur

Earth Way

Earth Way 2100P Estate Manuel utilisateur

Earth Way

Earth Way 2170 Manuel utilisateur

Earth Way

Earth Way 2050 Manuel utilisateur

Earth Way

Earth Way M20 Manuel utilisateur

Earth Way

Earth Way EV-N-Spred C22HD Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C24HD Manuel utilisateur

Manuels Épandeur populaires d'autres marques

PEQUEA

PEQUEA GT-100 Manuel utilisateur

Herculano

Herculano H2RS9 Manuel utilisateur

Epoke

Epoke SKE8 Manuel utilisateur

GEA

GEA EL44 Fiche technique

Boss Snowplow

Boss Snowplow TGS 800 Manuel utilisateur

Fisher

Fisher EMERSON 168 Series Manuel utilisateur

Fisher

Fisher POLY-CASTER 78601 Manuel utilisateur

TurfEx

TurfEx RS7200 Manuel du propriétaire

Ferris

Ferris Pathfinder Series Manuel utilisateur

Fayat Group

Fayat Group DYNAPAC S100 Guide de dépannage

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation

EASTMAN

EASTMAN CR 500 Manuel utilisateur

Nogueira

Nogueira RoyalFlow-600 Manuel utilisateur

Buyers

Buyers TGS05B Manuel utilisateur

Magnum

Magnum V-BOX PV Series Supplément

Meyer's

Meyer's VB280 Manuel utilisateur

SnowEx

SnowEx VX-4210 Manuel utilisateur

Kramer

Kramer VM-400HDCP Manuel utilisateur