Earth Way 2170 Manuel utilisateur

36210

Qty 2

36214

Qty 4 31100

Qty 4

31120

Qty 5

32103

Qty 9

31106

Qty 2

32100

Qty 2

33117

Qty 1

36105

Qty 1

33108

Qty 1

33109

Qty 1

36300

Qty 6

12152

Qty 2 12148

Qty 2

vvvvvvvv

26 9

1. Remove and identify all loose parts from carton.

(Qty 4 #36214)

1/4-20 X 1-1/2”

Phillips Panhead

(Qty 4 #36300)

1/4-20 SS Locknut

2. Position hopper on side. Install frame using (4) 1/4-20 x 1-1/2” Pan

Head Phillips bolts and (4) 1/4-20 nylon insert locknuts. First put bolts

through holes in frame then through holes in bottom of hopper. Secure

with locknuts. TIGHTEN THESE LOCKNUTS NOW - DO NOT

TIGHTEN WITH POWER TOOLS.

Pt# 52164 PAGE 1

2170 CommerCial

BroadCast spreader

ASSEMBLY and OPERATING INSTRUCTIONS Rev. 3-10

HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY

;If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader. The

impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise. Clean the impeller

plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.

;Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds

will change the spread patterns. Wet fertilizer will also change the spread pattern and ow rate. Clean and dry your

spreader thoroughly after each use. A coating of light spray oil on all metal parts inside & out will help prevent corrosion.

Wash between the shut off plate and bottom of the hopper. Do not use powdered materials.

;Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.

EarthWay

EV-N-SPRED

PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS

REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT

SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: teChsupport@earthway.Com SKYPE: EARTHWAY.TECH

roCk salt and powdered materials

should not Be used in this spreader as

it will damage gearBox and Can void

warranty.

use only granular materials.

Gearbox & Axle Assembly

Drive wheel side

Coast wheel side

Frame brace

1/4-20 x 1-1/2”

Hex Head Bolt

1/4-20 x 2-1/4”

Hex Head Bolt

1/4-20 Locknut

Impeller

Cross Brace

Dimples

Frame

Lower Handle

Pivot Rod

Shut-Off

1/4-20 x 1-1/2”

Pan Head Bolt

Step 6B

Step 6C

Step 6A

3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin

through impeller then through pinion shaft. Use hole closest to the

gear box. Spread cotter pin to prevent from falling out. Next insert

Cross Brace thru the Gearbox Brace as shown above.

Pinion

Shaft

1/8 x 1-1/4”

Cotter Pin (#36105)

DRIVE WHEEL

HOLE

COAST WHEEL

HOLE

Impeller

Cross Brace

Gearbox & Axle Assembly

Gearbox Brace

EarthWay

EV-N-SPRED

4. Install gear box by inserting the pinion shaft into hole in

center of hoppers bottom. The word “FRONT” on the gearbox

must point to Front of the hopper. Follow label instructions on

hopper.

Axle Bearing

Flat

Side

Notch

5. Install axle bearings to both lower handles.

NOTE: Notch on bearings and lower

handles. Bearings must go through at side

of lower handle.

6. A - Install lower handles onto axle to both sides as shown. Insert 2¼” bolt through second

hole in lower handle and through rst hole in frame install locknut. DO NOT TIGHTEN.

B - Now insert 1½” bolt through rst hole in lower handle. Then through frame brace.

NOTE: Dimples on frame brace must be facing toward gear box as shown. Next into threaded

connector in cross brace. DO NOT TIGHTEN.

C - Next insert 1½” bolt through other end of frame brace and through second hole in frame

install locknut.

NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP.

DO NOT OVER TIGHTEN.

PAGE 2

Gearbox

Axle Assembly

Lower

Handle

Frame

Brace

Cross Brace

Axle Bushing

7. Slide axle bushing over axle and into axle bearing to both

sides as shown.

8. Install drive wheel onto the axle and align with the cotter pin hole

nearest to lower handles as shown. Insert 2” cotter pin through wheel

and through axle. Bend with pliers to prevent pin from falling out.

9. Install coast wheel onto the axle fully, then using outside cotter pin

hole, insert 1” cotter pin through axle (not thru the wheel). Bend with

pliers to prevent pin from falling out.

2” Cotter Pin

1” Cotter Pin

10. NOTE: BEFORE INSTALLING GAUGE AND UPPER

HANDLES TO HANDLE SHAFT, UPPER HANDLES

FEATURE THREE POSITIONS FOR OPERATOR’S

COMFORT. If operator chooses middle or upper positions,

use handle spacer in hole nearest to handle grips. Insert

2” bolt through upper handle, then through handle spacer

through other upper handle. DO NOT TIGHTEN LOCKNUT

YET. TIGHTEN THIS NUT LAST. Install gauge & lever

using (2) 2” bolts. Be sure gauge is on left hand side.

Tighten locknuts on the gauge rst. TIGHTEN NOW.

11. Next insert the pivot rod into shut off plate as shown,

with the DOUBLE BEND is closest to the shut-off. Turn

to lock in place.

12. Insert other end of pivot rod into pivot and bracket

assembly as shown. Turn to lock in place.

TURN SPREADER UPRIGHT ON TO WHEELS.

1/4-20 x 2”

Hex Head

Bolt

Gauge &

Lever Assembly

Handle

Spacer

Upper Handles

1/4-20

Locknuts

POSITIONS

LOWER

MIDDLE

UPPER

Handle Shaft

Long end

Shut-Off

Plate

Pivot Rod

with extra bend

Rotate

Pivot

PAGE 3

Insert Pivot Rod

into Shut-Off

and rotate to secure

Angle

Attaching

Arm

Pivot

Rod

Gauge & Lever

Control Rod

Tabbed Hole

Control Rod

Lever Tensioning Nut

1/4 - 20 Lock-nut

1/4 - 20 x 2” Bolt

Pivot Bracket

Long End

Holes are farther

from one end

Handle Shaft

14. Install (1) 1/4-20 Hex

nut (not a locknut) on to

control rod as shown.

15. Install attened end of control rod in to lever on gauge as shown. Turn to lock in place. Next push lever forward to setting “0”. Align

control rod with hole in pivot bracket, pull lever backward to insert control rod through hole in pivot bracket. Now install 1/4-20 Hex nut on

to control rod.

16. Pull lever back to setting “30” as shown. Next push pivot & bracket forward so that the shut off plate in the hopper is in the full open

position. REMEMBER SETTING “30” ON THE FLOW CONTROL LEVER MUST PLACE THE SHUT-OFF PLATE IN THE FULL

OPEN POSITION TO BE PROPERLY CALIBRATED. Now tighten the nuts against the pivot bracket to prevent change in calibration.

17. Tension on the ow control lever may be adjusted by tightening or loosening the tension nut as shown.

1/4-20

Hex Nuts

Pivot

Bracket

Control

Rod

18. Insert agitator to pinion shaft on inside of hopper.

Note: the position of at side of the agitator. This pin

should be installed as shown.

PAGE 4

13. Install handle shaft to lower handles and pivot & bracket assembly as shown. Using 1/4 -20 x 2” bolts and

locknuts. TIGHTEN BOLTS AND NUTS NOW.

1/4-20 x 1”

Hex Head Bolt

Stainless

1/4-20 Lock Nut

Stainless

19. Install debris screen into hopper, then insert 1/4-20 x 1”

Stainless Steel Hex Bolt thru the hole in the side wall of the hopper.

Secure with Stainless Steel lock nut - TIGHTEN WITH HAND

TOOLS ONLY

PAGE 5

The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of

material applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to the

above conditions, the manufacturer makes no warranty as to the uniformity of coverage actually obtained from the settings

listed.

HOW TO ORDER SPARE PARTS

All spare parts listed herein may be ordered direct from the manufacturer. Be sure to give the following information when ordering.

;Model Number

;Part Number

;Part Description

You can contact us by calling (574) 848-7491 or 800-294-0671 to place an order with a credit card.

Questions? Parts@earthway.com

Full Rate Path Half Rate Path

Start

Finish

Start

Finish

OPERATING INSTRUCTIONS

Before lling hopper, become familiar with the operation of this spreader.

5Obtain proper setting for material to be used from the enclosed SETTING MATRIX included with this spreader, or from our web site

under the MANUALS SECTION.

5Move stop bolt on rate gauge assembly to the proper setting.

5While pushing spreader forward, pull control lever back to stop bolt.

5To stop, push lever forward to close ow holes before you stop moving.

5When nished, empty any remaining material from hopper.

5Thoroughly wash spreader and allow to dry before storing. A coating of light oil will help prevent corrosion.

5If you must use Rock Salt, Remove agitator when using Rock Salt to prevent damage to the gearbox.

2170 BroadCast spreader ~ Parts List

KEY # PART # DESCRIPTION KEY # PART # DESCRIPTION

1 40003 SQUARE SCREEN 22 12317 SHUT OFF PLATE (BLACK)

2 60335 HOPPER ASSEMBLY 23 25222 LOWER HANDLE Square

3 33117 AGITATOR 24 25106 FRAME

4 12209 HOPPER BUSHING 25 44249 FRAME BRACE

5 36214 1/4-20 X 1 1/2" PHPMS SS 26 24704 CROSS BRACE (11.25")

6 32110 1/4-20 LOCK NUT ZINC 27 31106 1/4-20 X 2 1/4" HHCS ZINC

7 36210 1/4-20 X 1" HHMS SS 28 12109 IMPELLER (9" DIA)

8 31120 1/4-20 X 2" HHCS ZINC 29 36105 1/8" X 1 1/4" COTTER PIN SS

9 60300 PIVOT & BRACKET ASSEMBLY 30 12274 GRIP 7.5" LONG

10 32103 1/4-20 NYLON INS LOCKNUT ZINC 31 60334 GEAR BOX & AXLE ASS'Y

11 44251 PIVOT ROD 32 12148 AXLE BEARING

12 60298 GAUGE & LEVER ASSEMBLY 33 12152 AXLE BUSHING

13 60175 UPPER HANDLE Square w/GRIP 34 33109 3/16" X 2" COTTER PIN ZINC

14 12344 HANDLE SPACER Square Shaft 35 70138 PNEUMATIC DRIVE/COAST WHEEL STUD

15 31100 1/4-20 X 1 1/2 HHMS ZINC 37 33108 3/16" X 1" COTTER PIN ZINC

16 25223 HANDLE SHAFT Square 38 11927 SHUTOFF SUPPORT- LARGE

17 42256 CONTROL ROD OPTIONAL 60060R SIDE DEFLECTOR AND RAIN COVER

18 31138 #8 X 3/8" PMT #8 HD COARSE BLACK OPTIONAL 77002 HEAVY DUTY RAIN COVER 19"X 19”

19 36300 1/4-20 NYLON INSERT LOCKNUT SS OPTIONAL 12195 GAUGE OVERLAY- LESCO

20 32100 1/4-20 HEX NUT ZINC 12196 GAUGE OVERLAY- EARTHWAY

21 36208 #6 X 3/8" TYPE 25 PHPS SS

vvvvvvvv

30 6

15 25

22 23

13 14

77002

OPTIONAL

Heavy-Duty

Rain Cover

60060R

OPTIONAL

Heavy-Duty

Rain Cover

Side Deflector Kit

60166R

OPTIONAL

3-Side Salt

Deflector Kit

EarthWay

Products, Inc.

P.O. Box 547

Bristol, IN 46507

Phone: 800-294-0671

www.earthway.com

Standard Settings (12196) Gauge Overlay and

OPTIONAL Lesco Settings (12195) Gauge Overlay

Autres manuels pour 2170

Table des matières

Autres manuels Earth Way Épandeur

Earth Way

Earth Way 2130 Manuel utilisateur

Earth Way

Earth Way 2600A-Plus Estate Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way 2600A-Plus Estate Manuel utilisateur

Earth Way

Earth Way Ev-N-SprEd 2030 Series Manuel utilisateur

Earth Way

Earth Way FLEX-SELECT Series Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C22HD Manuel utilisateur

Earth Way

Earth Way 7350SU Manuel utilisateur

Earth Way

Earth Way 2130 High-Output Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED C22HD Manuel utilisateur

Earth Way

Earth Way 2050T Manuel utilisateur

Earth Way

Earth Way 2170-XL Manuel utilisateur

Earth Way

Earth Way 2170 Manuel utilisateur

Earth Way

Earth Way 3100 Manuel utilisateur

Earth Way

Earth Way Prizelawn BF l Manuel utilisateur

Earth Way

Earth Way 2600A-Plus Manuel utilisateur

Earth Way

Earth Way 2170 Manuel utilisateur

Earth Way

Earth Way EV-N-SPRED 2150 Manuel utilisateur

Earth Way

Earth Way 2050TP Manuel utilisateur

Earth Way

Earth Way Ev-N-Spred 2050 Manuel utilisateur

Earth Way

Earth Way M40 Manuel utilisateur

Earth Way

Earth Way FLEX-SELECT F80 Series Manuel utilisateur

Earth Way

Earth Way M80ECM Manuel utilisateur

Earth Way

Earth Way M20 Manuel utilisateur

Manuels Épandeur populaires d'autres marques

PEQUEA

PEQUEA GT-100 Manuel utilisateur

Herculano

Herculano H2RS9 Manuel utilisateur

Epoke

Epoke SKE8 Manuel utilisateur

GEA

GEA EL44 Fiche technique

Boss Snowplow

Boss Snowplow TGS 800 Manuel utilisateur

Fisher

Fisher EMERSON 168 Series Manuel utilisateur

Fisher

Fisher POLY-CASTER 78601 Manuel utilisateur

TurfEx

TurfEx RS7200 Manuel du propriétaire

Ferris

Ferris Pathfinder Series Manuel utilisateur

Fayat Group

Fayat Group DYNAPAC S100 Guide de dépannage

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation

EASTMAN

EASTMAN CR 500 Manuel utilisateur

Nogueira

Nogueira RoyalFlow-600 Manuel utilisateur

Buyers

Buyers TGS05B Manuel utilisateur

Magnum

Magnum V-BOX PV Series Supplément

Meyer's

Meyer's VB280 Manuel utilisateur

SnowEx

SnowEx VX-4210 Manuel utilisateur

Kramer

Kramer VM-400HDCP Manuel utilisateur