Dimplex DFI400R Manuel utilisateur

Owner’s Manual

Model

DFI400R (6909051242)

CDFI400C/DFI400C (6909051243)

DFI600R (6909051262)

DFI600C (6909051263)

CDFI600L (6909051261)

7213750100R02

IMPORTANT SAFETY INFORMATION: Always read this manual

rst before attempting to install or use the Optimyst® cassette. For

your safety, always comply with all warnings and safety instructions

contained in this manual to prevent personal injury or property

damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this cassette.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations....................3

IMPORTANT INSTRUCTIONS ..................4

Installation..................................6

Assembly...................................8

Operation..................................10

Maintenance...............................12

Warranty .................................14

Replacement Parts ..........................16

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an Optimyst®

cassette from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your cassette.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

Model Number

Serial Number

4 www.dimplex.com

IMPORTANT SAFETY INSTRUCTIONS

THE ELECTRICAL RATING

FOR THESE MODELS

(6909051242, 6909051243,

6909051262,6909051263,

6909051261) IS 120VAC, 60 HZ,

200W.

When using an electrical furnish-

ing, basic precautions should

always be followed, including the

following:

Read all instructions before using

(this furnishing).

DANGER: To reduce the risk

of electric shock always unplug

this furnishing from the electri-

cal outlet before cleaning.

WARNING: To reduce the risk

of burns, re, electric shock, or

injury to persons:

① Unplug from outlet before putting

on or taking off parts.

② Close supervision is necessary

when this furnishing is used by, or

near children, invalids, or disabled

persons.

③ Use this furnishing only for its

intended use as described in these

instructions. Do not use attach-

ments not recommended by the

manufacturer.

④ Never operate this furnishing if it

has a damaged cord or plug, if it is

not working properly, if it has been

dropped or damaged, or dropped

into water. Contact Dimplex Techni-

cal Service at 1-888-346-7539 for

replacement parts.

⑤ Keep the cord away from heated

surfaces.

⑥ Never operate the furnishing with

the air openings blocked. Keep the

air openings free of lint, hair, and

the like.

⑦ Never drop or insert any object

into any opening.

⑧ Do not use outdoors.

⑨ Do not operate where aerosol

(spray) products are being used

or where oxygen is being adminis-

tered.

⑩ To disconnect, turn all controls to

the off position, then remove plug

from outlet.

WARNING: Risk of Electric

Shock – Connect this furnishing

to a properly grounded outlet

only. See Grounding Instruc-

tions.

⑪ This electrical appliance has hot

and arcing or sparking parts inside.

Do not use in areas where gaso-

line, paint, or ammable liquids are

used or stored.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

⑫ Do not modify the unit. Use it

only as described in this manual.

Any other use not recommended by

the manufacturer may cause re,

electric shock or injury to persons.

⑬ To reduce the risk of electric

shock, this appliance has a three

pronged plug. This plug will t in a

grounded outlet only one way. If the

plug does not t, contact a quali-

ed electrician to install the proper

outlet. Do not change the plug in

any way. Always plug this appliance

directly into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑭ Keep away from curtains, drap-

eries and similar materials.

⑮ Always use a certied electrician

should new circuits or outlets be

required.

⑯ Always use properly grounded,

fused and polarized outlets.

⑰ When transporting or storing the

unit and cord, keep in a dry place,

free from excessive vibration and

store so as to avoid damage.

⑱ This furnishing has not been

evaluated for ammability or ciga-

rette ignition resistance.

⑲ Do not submerse.

⑳ Light bulb requirement: 45W,

12VAC halogen bulbs type MR 16.

Contact Dimplex Technical Service

at 1-888-346-7539 for replacement

bulbs.

㉑ The electric fireplace shall be

installed in an enclosure no smaller

than that indicated. (See Figure 2)

!NOTE: Changes or modica-

tions not expressly approved by the

party responsible for compliance

could void user's authority to oper-

ate the equipment.

WARNING: Remote control con-

tains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

6 www.dimplex.com

Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

Grounding Instructions

This product must be grounded.

If it should malfunction or break-

down, grounding provides a path

of least resistance for electric

current to reduce the risk of

electric shock. This product is

equipped with a cord having an

equipment-grounding conductor

and a grounding plug. The plug

must be plugged into an appropri-

ate outlet that is properly installed

and grounded in accordance with

all local codes and ordinances.

DANGER: Improper connec-

tion of the equipment-grounding

conductor can result in a risk

of electric shock. Check with a

qualied electrician or serviceman

if you are in doubt as to whether

the product is properly grounded.

Do not modify the plug provided

with the product – if it will not t

the outlet, have a proper outlet

installed by a qualied electrician.

This product is for use on a

nominal 120-volt circuit and has

a grounding plug that looks like

the plug in Figure 1. Make sure

that the product is connected to

an outlet having the same con-

guration as the plug. No adapter

should be used with this product.

CAUTION: Risk of Electric

Shock. Unplug the cord before

moving or servicing this furnishing.

!NOTE: A 15 Amp, 120 Volt cir-

cuit is required. A dedicated circuit

is preferred but not essential in

all cases. A dedicated circuit will

be required if, after installation,

the circuit breaker trips or fuse

blows on a regular basis when the

cassette is operating. Additional

appliances on the same circuit

may exceed the current rating of

the circuit breaker.

Mantel Installation

Install the replace into the

mantel (refer to mantel assembly

instructions).

Figure 1

Installation

Figure 2

New Construction

1. Mark the desired location on

the oor and store the replace

in a safe, dry and dust free

location.

2. Use studs to frame an enclo-

sure with the following mini-

mum internal/opening dimen-

sions (Figure 2).

!NOTE: An air inlet is required

for optimum mist production, see

Figure 2 for minimum dimen-

sions.

!NOTE: For optimal perfor-

mance, 12 in. (305 mm) mini-

mum clearance between the in-

stallation surface and any surface

above should be maintained.

3. Secure unit through the two

holes in the bottom of the unit

into supports to prevent the

unit from hanging from the top

ange, see gure 3 for dimen-

sions.

4. The unit is equipped with a

power supply plug, the plug

should be plugged directly into

a 15 A, 120 V outlet.

8.5 in.

(216mm)

6.7 in.

(170mm)

Exit for Cord

Installation

Surface

Supports: 0.75 in. (19 mm) high

DFI400: 15.75 in. (400mm)

DFI600: 22.05 in. (560mm)

Air Inlet

DFI400: 100cm2

DFI600: 150cm2

Figure 3

FRONT

1.2 in.

(30.0 mm)

3.5 in.

(90.0 mm)

3.1 in.

(80.0 mm)

4.8 in.

(122.0 mm)

5.4 in.

(137.0 mm)

1.2 in.

(30.0mm)

8 www.dimplex.com

Assembly

Figure 4

1. Carefully unpack all of the

components from the box.

(Figure 4)

2. Remove top cover by turning

the retaining tabs on both

ends of the water reservoir.

(Figure 5)

3. Install the light bulbs by

aligning the pins on the bulbs

and the xture and pressing

down until they are fully

inserted. (Figure 6)

4. Install the transducer so that

it is sitting level in the circular

holding area in the reservoir.

5. Orient transducer wire so that

it does not sit directly above

the emitter and the wire

passes through the slot in the

side of the tank. (Figure 5)

6. Reinstall the top cover and

ensure both retaining tabs

have been turned so that they

are pointing inwards.

7. Fill and install the Rell

Container.

!NOTE: Normal tap water can

be used in the Optimyst® as long

as the tap water is not considered

to be hard water. In the event

your tap water is hard, you may

use softened water or distilled

water with 1/8 tsp of salt (0.5

mL) added to the water reservoir.

(The addition of additional salt

should only be used when you

notice that the unit is not produc-

ing mist as expected.)

!NOTE: During initial

installation, the Rell Container

Transducer

Rock

Media

Removable Rell

Container

Light Bulbs

Remote

Control

Curved Tray

Housing

Media

Tray

Logset

Figure 5

Top

Cover

Transducer

Emitter

Wire Slot

Assembly

should be relled after the

Reservoir has lled to ensure the

maximum operating time.

8. Install the media on top, media

tray and media (if applicable),

so that the opening is not

blocked (Figure 6).

CAUTION: Do not arrange the

media while the unit is running,

since the media and/or tray may be

hot.

9. Make sure the On/Off switch

is switched to Off (refer to

Operating Instruction section).

10. Plug the unit into a 15 Amp/

120 volt outlet.

Retaining

Tab

Figure 6

!NOTE: Rock media shown, install

other medias in the same way.

Fan

Housing

Water Tank

10 www.dimplex.com

Operation

!NOTE: Always ensure that the

appliance is in an upright position

before operating the unit.

!NOTE: When the cassette

is used in an environment where

background noise is very low, it

may be possible to hear a sound

which is related to the operation

of the ame effect. This is normal

and should not be a cause for

concern.

!NOTE: Always ensure that

the appliance is in a level position.

The manual controls for the cas-

sette are located on the top of

the unit, below the control cover.

(Figure 7)

A. On/Off Switch

Supplies power to the cassette.

B. Mode Selector Switch

Press once to turn on the ame

effect. This will be indicated by an

audible “beep”. Although the lights

turn on immediately it will take 30

seconds before the ame effect

starts.

Press to put re in to standby

mode. This will be indicated by

one “beep”.

C. Flame Intensity Control

Adjusts the intensity of the ame

effect when the cassette has

been activated.

Turning the control knob clock-

wise to decrease the intensity

of the ame effect. Turning the

control knob counter-clockwise

will increase the ame effect.

!NOTE: Give the ame genera-

tor some time to react to changes

you may make on the ame

control knob.

!NOTE: When the water tank is

empty the unit will turn off after 30

seconds. See instructions under

Maintenance Section for rell-

ing tank. When this procedure is

complete, the main lamps will illu-

minate but it will take 30 seconds

before the ames return.

Figure 7

Remote Control

Sensor

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dimplex Cheminée intérieure

Dimplex

Dimplex DMCS13R Manuel utilisateur

Dimplex

Dimplex CAS500R-RGB-EU Mode d’emploi

Dimplex

Dimplex SP420 Manuel utilisateur

Dimplex

Dimplex OPTIMYST RTOPCS20 Manuel utilisateur

Dimplex

Dimplex Wickson Manuel utilisateur

Dimplex

Dimplex DF2624L-INT Manuel utilisateur

Dimplex

Dimplex 25 FIREBOX Manuel utilisateur

Dimplex

Dimplex DF2690 Manuel utilisateur

Dimplex

Dimplex DCF44GS Manuel utilisateur

Dimplex

Dimplex Revillusion RBF24DLX Manuel utilisateur

Dimplex

Dimplex LVA231 Manuel

Dimplex

Dimplex VCX1525 Manuel utilisateur

Dimplex

Dimplex DWF3651 Manuel utilisateur

Dimplex

Dimplex Ignite 50" Manuel utilisateur

Dimplex

Dimplex TIMRA TMR15 Guide d'installation

Dimplex

Dimplex DF2524L Manuel utilisateur

Dimplex

Dimplex CAS20N-AU Manuel utilisateur

Dimplex

Dimplex EF2870 Manuel utilisateur

Dimplex

Dimplex MOZART MZT20 Manuel utilisateur

Dimplex

Dimplex Sierra 48 Manuel utilisateur

Dimplex

Dimplex BF392SD Manuel utilisateur

Dimplex

Dimplex DF2622 Manuel utilisateur

Dimplex

Dimplex PRISM BLF5051-AU Manuel utilisateur

Dimplex

Dimplex XHD23 Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation