Digitus Professional DN-60013 Manuel utilisateur
8-Port Fast Ethernet
10" rack-mount Switch
Manual
DN-60013
Introduction
The DN-60013 is a compact Ethernet desktop switch that provides wire-speed, a Fast
Ethernet switching function which allows high-performance, low-cost connections to
10M/100M bps Ethernet network. The Ethernet Switch delivers all the advantages of
a switching hub in a compact desktop size and is ideal for small office or SOHO
network users.
This switch provides 8 auto-sensing 10/100 Mbps Ethernet RJ-45 ports which
automatically detect the speed of the devices that you plug into them. This switching
function allows Full/Half-duplex devices to communicate on the same network
without having to replace any infrastructure. This flexible feature allows your
network a timely, economical migration to DIGITUS network switch.
Key Features
Conforms to IEEE802.3, 802.3u, 802.3x
Automatic MDI/MDIX crossover for all ports
N-Way Auto-negotiation for 10/100Mbps transmissions
Space-saving compact size
Store-and-Forward switching architecture
Auto-detection of full/half-duplex mode in all ports
Plug-and-Play configuration auto address learning
LED indicators for Power, Link/activity
Package Contents
Ethernet Switch
User’s manual
AC power cord
IMPORTANT: If any piece is missing or damaged, please contact your local dealer or
reseller for service.
Product Specifications
DN-60013 (8-Port 10/100Base-TX Fast Ethernet Switch)
Ports: 8-Port 10/100Base-TX
MAC Address: 1K Mac address table
LED Indicator: Per port: Link/Activity
Per unit: Power
Dimension: 250mm x 150mm x 42mm (W x D x H)
Operating Temp: 0°C to 45°C (32°F to 113°F)
Operating Humidity: 10% to 90% (Non-condensing)
Power Consumption: 5 Watt @ AC 100-240VAC 50/60Hz (Maximum)
EMI: CE Class A
Hardware Description
The Front Panel
The front panel consists of LED Indications.
LED Indicators
Per Device: Power
Per Port: LINK/ACT (Link/Activity)
Power Indicator
Figure 1. Front panel view
LED Status Color Description
Power On Green The switch is supplied with suitable power.
LINK/ACT Off - The port is not linked successfully with the device.
Figure 2. Back view
RJ-45 Ports (Auto MDI/MDIX)
8 auto-sensing ports of 10Base-T, 100Base-TX connections. [In general, MDI means
connecting to another Hub or Switch while MDIX means connecting to a workstation
or PC. Therefore, Auto MDI/MDIX means that you can connect to another Switch or
workstation without changing pin-to-pin or crossover cabling.]
AC POWER CONNECTOR
PLUG THE FEMALE CONNECTOR INTO THE SWITCH AND MALE CONNECTOR INTO
A POWER OUTLET. SUPPORTS INPUT VOLTAGES 100-240VAC, 50/60HZ.
Troubleshooting
The Switch can be easily monitored through panel indicators to assist in identifying
problems. This section describes common problems you may encounter and possible
solutions.
Power
If the power indicator does not light when the power cord is plugged in, you may
have a problem with the power outlet or cord. However, if the power LED goes off
after running for a while, check for loose power connections, power losses or surges
at the power outlet. Turn off power, wait 30 seconds and turn power on again. If
problem is still not resolved call for dealer’s assistance
Diagnosing LED Indicators
If link indicator does not light after making a connection, check whether network
interface (e.g., a network adapter card on the attached device), network cable, or
switch port is defective. Be sure the cable is plugged into both the switch and
corresponding device. Verify the proper cable type is used and its length does not
exceed specified limits.
Cabling
Verify that the cabling type is correct. Make sure all cable connectors are securely
seated in the required ports. Use only standard Unshielded Twisted-Pair (UTP),
Category 3, 4, 5, or 5e cables. Use only Category 5 or 5e when connecting with Fast
Ethernet. Make certain the maximum distance between the Switch and what it’s
connected to be 100 meters or less.
NOTE: Do not plug a standard telephone cord into an RJ-45 port. This may damage
the switch
This is a Class A product. In home environment, this product may cause radio interference. In
this case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the
shipping content. If the Declaration of Conformity is missing, you can request it by post
under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Table des matières
Autres manuels Digitus Changer
Digitus
Digitus DS-23100-1 Manuel utilisateur
Digitus
Digitus DA-70255 Manuel utilisateur
Digitus
Digitus DN-651118 Manuel utilisateur
Digitus
Digitus DN-95140 Manuel utilisateur
Digitus
Digitus DN-651113 Manuel utilisateur
Digitus
Digitus DA-70240 Manuel utilisateur
Digitus
Digitus DN-95315 Manuel utilisateur
Digitus
Digitus DN-80064-1 Manuel utilisateur
Digitus
Digitus DA-70250-1 Manuel utilisateur
Digitus
Digitus DA-70246 Manuel utilisateur
Digitus
Digitus DN-60021-1 Manuel utilisateur
Digitus
Digitus DA-70243 Manuel utilisateur
Digitus
Digitus DS-45320 Manuel utilisateur
Digitus
Digitus DS-44100-1 Manuel utilisateur
Digitus
Digitus DC OC-12 Manuel utilisateur
Digitus
Digitus DN-95341 Manuel utilisateur
Digitus
Digitus DN-95323-1 Manuel utilisateur
Digitus
Digitus DC-11101-1 Manuel utilisateur
Digitus
Digitus DS-12423 Manuel utilisateur
Digitus
Digitus DA-70244 Manuel utilisateur
