DFI CM64-AL Manuel utilisateur

90200547

CM64-AL

System Board

User’s Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks of

Microsoft Corporation. VIA is a registered trademark of VIA

Technologies, Inc. Award is a registered trademark of Award Soft-

ware, Inc. Other trademarks and registered trademarks of products

appearing in this manual are the properties of their respective

holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.....................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

Internal I/O Connectors.....................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers, Utilities and Software Applications......................................................

Installation Notes.......................................................................................................................

Appendix A - System Error Messages...............................................

POST Beep.................................................................................................................................

Error Messages.........................................................................................................................

Appendix B - Troubleshooting..........................................................

Troubleshooting Checklist...............................................................................................

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product

specifications.

2. The warranty is void if the product has been subjected to

physical abuse, improper installation, modification, accidents or

unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service,

adjustments or repairs on the product, whether in or out of

warranty. It must be returned to the purchase point, factory or

authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and

connectors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk

drive and other components. Perform the upgrade instruction

procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection

by wearing an antistatic wrist strap and attaching it to a metal

part of the system chassis. If a wrist strap is unavailable,

establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;A user’s manual

;One IDE cable

;One floppy cable

;One “Mainboard Utility” CD

The system board and accessories in the package may not come

similar to the information listed above. This may differ in accordance

to the sales region or models in which it was sold. For more

information about the standard package in your region, please

contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Introduction

Chapter 1 - Introduction

Specifications

Processor

Chipset

System Memory

Expansion Slots

BIOS

Power Management

Hardware Monitor

Graphics

Audio

Pentium®III

- FCPGA2 133MHz FSB (1.13GHz-1.26GHz on 0.13µ)

- FCPGA 133MHz FSB (533EB-1GHz)

- FCPGA 100MHz FSB (500E-1.1GHz)

CeleronTM

- FCPGA2 100MHz FSB (≥1.2GHz on 0.13µ)

- FCPGA 100MHz FSB (800MHz-1.1GHz)

VIA®chipset

- North bridge: VIA®Apollo PLE133T 8601T

- South bridge: VIA®82C686B

Supports up to 1GB using VCM (Virtual Channel Memory) or

PC SDRAM DIMM (unbuffered or registered)

Two 168-pin DIMM sockets

Uses x64 PC SDRAM, 3.3V

- PC-100 SDRAM DIMM for 100MHz FSB processors

- PC-133 SDRAM DIMM for 133MHz FSB processors

4 PCI slots

3 ISA slots

Award BIOS

2Mbit flash memory

ACPI and OS Directed Power Management

ACPI STR (Suspend to RAM) function

Wake-On-PS/2 Keyboard/Mouse

Wake-On-USB Keyboard/Mouse

Wake-On-LAN

Wake-On-Ring

RTC timer to power-on the system

AC power failure recovery

Monitors CPU/system temperature and overheat alarm

Monitors VCORE/3.3V/5V/12V voltages and failure alarm

Monitors CPU/chassis fan speed and failure alarm

CPU Overheat Protection function monitors CPU temperature

during system boot-up

Integrated Trident 2D/3D video accelerator

Realtek ALC202A AC’97 audio CODEC

2-channel audio output

Introduction

LAN

IDE

Rear Panel I/O

Internal I/O

PCB

Realtek RTL8100C PCI LAN

Fully compliant to IEEE 802.3 (10BASE-T) and 802.3u

(100BASE-TX) standards

Supports two IDE connectors that allows connecting up to four

UltraDMA 100Mbps hard drives

1 mini-DIN-6 PS/2 mouse port

1 mini-DIN-6 PS/2 keyboard port

1 RJ45 LAN port

2 USB 1.1 ports

1 parallel port

1 COM port

1 VGA port

1 game port

Line-out, line-in and mic-in jacks

1 connector for 2 additional external USB 1.1 ports

1 connector for 1 external COM port

1 front audio connector for external line-out and mic-in jacks

1 CD-in internal audio connector

1 AUX-in internal audio connector

1 IrDA connector

2 IDE connectors

1 floppy connector

1 Wake-On-LAN connector

1 Wake-On-Ring connector

1 20-pin ATX main power connector

1 front panel connector

2 fan connectors

ATX form factor

20.1cm (7.92") x 30.5cm (12")

Introduction

Features

The integrated Trident video accelerator supports

optimized Shared Memory Architecture (SMA) and

shares 8MB of the system memory. 3D rendering

features 32-bit true color rendering and MPEG-2 video

textures. It also supports 2D hardware acceleration features.

CPU Overheat Protection has the capability of

monitoring the CPU’s temperature during system boot

up. Once the CPU’s temperature exceeded the

temperature limit pre-defined by the CPU, the system will automatically

shutdown. This preventive measure has been added to protect the

CPU from damage and insure a safe computing environment.

The two DIMM sockets support PC SDRAM

DIMMs. PC SDRAM (Synchronous Dynamic

Random Access Memory) uses a fast memory interface technology

that includes using the clock on the chip to synchronize with the

CPU clock so that the timing of the memory chips and the timing of

the CPU are synchronized. This saves time during transmission of

data, subsequently increasing system performance.

The onboard Realtek ALC202A which is an AC’97

compatible audio codec supports 2-channel audio

output.

The Realtek RTL8100C PCI LAN supports up to

100Mbps.

CPU

Overheat

Protection

PC SDRAM

AUDIO

Autres manuels pour CM64-AL

Table des matières

Autres manuels DFI Carte mère

DFI

DFI AL102 Manuel utilisateur

DFI

DFI AM33-EC Manuel utilisateur

DFI

DFI AD73 Pro Manuel utilisateur

DFI

DFI PS82-BC/BL Manuel utilisateur

DFI

DFI M8MP553 Manuel utilisateur

DFI

DFI AK34-SC Manuel utilisateur

DFI

DFI G586OPC/E Manuel utilisateur

DFI

DFI EHL171 Manuel utilisateur

DFI

DFI NB60-EL Manuel utilisateur

DFI

DFI AL170 Manuel utilisateur

DFI

DFI CP900-B Manuel utilisateur

DFI

DFI EL630-NR Manuel utilisateur

DFI

DFI CA63-SC Manuel utilisateur

DFI

DFI MB330-CRM Manuel utilisateur

DFI

DFI CS62-TC Manuel utilisateur

DFI

DFI G586VPM Manuel utilisateur

DFI

DFI KD331-C236/Q170 Manuel utilisateur

DFI

DFI HD101-H81 Manuel utilisateur

DFI

DFI ADS310-R680E Series Manuel utilisateur

DFI

DFI HD330-Q87 Manuel utilisateur

DFI

DFI G7L332-L Manuel utilisateur

DFI

DFI CMS311-W480E/Q470E Manuel utilisateur

DFI

DFI CL630-CRM Manuel utilisateur

DFI

DFI lanparty dk P45 series Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur