DFI AM36-EC Manuel utilisateur

AM36-EC

AM36-TC

Rev. D+

System Board

Users Manual

49210136

Copyr ght

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose. The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft® MS-DOS®, WindowsTM, Windows® 95, Windows® 98,

Windows® 98 SE, Windows® ME, Windows® 000 and Windows

NT® 4.0 are registered trademarks of Microsoft Corporation. AMD,

AthlonTM and DuronTM are registered trademarks of Advanced Micro

Devices, Inc. VIA is a registered trademark of VIA Technologies, Inc.

Award is a registered trademark of Award Software, Inc. Other

trademarks and registered trademarks of products appearing in this

manual are the properties of their respective holders.

Caut on

To avoid damage to the system:

 Use the correct AC input voltage range.

To reduce the risk of electric shock:

 Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

 Danger of explosion if battery incorrectly replaced.

 Replace only with the same or equivalent type recommend by

the manufacturer.

 Dispose of used batteries according to the battery

manufacturers instructions.

Joystick or MIDI port:

 Do not use any joystick or MIDI device that requires more than

10A current at 5V DC. There is a risk of fire for devices that

exceed this limit.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to tr y to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

. Shielded interface cables must be used in order to comply with

the emission limits.

Not ce

This users manual contains detailed information about the system

board. If, in some cases, some information doesnt match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the users manual, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click Users

Manual.

System Board

This users manual is for the AM36-EC and AM36-TC system

boards. The differences between these system boards are shown

below.

Chipset

- KM133

- KM133A

CPU

- 00MHz FSB

- 00/ 66MHz FSB

CPU FSB select (JP11)

AM36-TC

AM36-EC

Ta le of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1. Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

.1 System Board Layout .............................................................................................

. System Memory.............................................................................................................

.3 Jumper Settings for Clearing CMOS Data..........................................

.4 Jumper Settings for the Onboard Audio Codec...........................

.5 Jumper Settings for Selecting the CPUs Front Side Bus........

.6 Jumper Settings for Selecting the USB Power...................................

.7 Ports and Connectors.............................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1. Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.1 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

3. Updating the BIOS.....................................................................................................

Introduction



Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4. VIA Hardware Monitor............................................................................................

4.3 VIA Service Pack..........................................................................................................

4.4 Audio Drivers and Software Application...............................................

4.5 Graphics Drivers............................................................................................................

4.6 Microsoft DirectX 7.0 Driver.............................................................................

4.7 Drivers and Utilities Installation Notes.....................................................

Appendix A - Using the Suspend to RAM

Function

A.1 Using the Suspend to RAM Function........................................................

Appendix B - System Error Messages

B.1 POST Beep.......................................................................................................................

B. Error Messages..............................................................................................................

Appendix C - Trou leshooting

C.1 Troubleshooting Checklist....................................................................................



Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA® KM133 - VT8365 and VT8 C686B (AM36-EC)

 VIA® KM133A - VT8365A and VT8 C686B (AM36-TC)

Processor

The system board is equipped with Socket-A for 46 -pin PGA

processor. It is also equipped with a switching voltage regulator that

automatically detects 1.100V to 1.850V.

 AM36-EC

- AMD AthlonTM/DuronTM 00MHz FSB processor (600/650/

700/750/800/850/900/950MHz, 1GHz, 1. GHz or future

processors)

 AM36-TC

- AMD AthlonTM/DuronTM 00/ 66MHz FSB processor (600/

650/700/750/800/850/900/950MHz, 1GHz, 1.1GHz, 1. GHz

or future processors)

- AMD AthlonTM XP processor (1500+, 1600+ or 1700+)

System Memory

 Supports up to 1GB using VCM (Virtual Channel Memory) or

PC SDRAM DIMM (unbuffered or registered)

 Two 168-pin DIMM sockets

 Uses x64 PC SDRAM, 3.3V

- PC-100 SDRAM DIMM for 100MHz memory bus

- PC-133 SDRAM DIMM for 133MHz memory bus

 L cache memory

- DuronTM processor: built-in 64KB Level pipelined burst

cache

- AthlonTM processor: built-in 56KB Level pipelined burst

cache

Chapter 1 - Introduction

Introduction



Expansion Slots

The system board is equipped with 1 universal AGP slot. AGP is an

interface designed to support high performance 3D graphics cards. It

utilizes a dedicated pipeline to access system memory for texturing,

z-buffering and alpha blending. The universal AGP slot supports AGP

x with up to 533MB/sec. bandwidth and AGP 4x with up to

1066MB/sec. bandwidth for 3D graphics applications. AGP in this

system board will deliver faster and better graphics to your PC.

The system board is also equipped with dedicated PCI slots and

1 shared PCI/CNR slot. CNR (Communication and Networking

Riser) is an interface that can support multi-channel audio, V.90

analog modem, phone-line based networking or 10/100 Ethernet

based networking riser board.

On oard Graphics Features

 Integrated Savage4 D/3D/Video accelerator

- Shares MB to 3 MB of the system memory

- Optimized Shared Memory Architecture (SMA)

- Full AGP 4x, including sideband addressing and execute mode

- High quality DVD video playback

 3D rendering features

- 3 -bit true color rendering

- MPEG- video textures

 D hardware acceleration features

DIMMs

MBx64

4MBx64

8MBx64

Memory Size

16MB

3 MB

64MB

DIMMs

16MBx64

3 MBx64

64MBx64

Memory Size

1 8MB

56MB

51 MB

Important:

 PC-100 SDRAM DIMM is supported when used with

200MHz FSB processor

 PC-133 SDRAM DIMM is supported when used with

200MHz FSB or 266MHz FSB processor

 If you are using more than one DIMM, make sure you

insert the same type of DIMMs into the DIMM sockets

Using different types (VCM or PC SDRAM) of DIMMs may

cause problems



Introduction

 Motion video architecture

 Software drivers

- Windows® 95/98/ 000/ME

- Windows NT® 4.0

On oard Audio Features

 Supports Microsoft® DirectSound

 Standard v1.0 or v .0 AC'97 codec

 AC97 supported with full duplex, independent sample rate

converter for audio recording and playback

 Downloadable sound (DLS) level-1

 Supports 1W audio amplifier on line-out jack

ATX Dou le Deck Ports (PC 99 color-coded connectors)

 Two USB ports

 One NS16C550A-compatible DB-9 serial port

 One DB-15 VGA por t

 One SPP/ECP/EPP DB- 5 parallel port

 One mini-DIN-6 PS/ mouse port

 One mini-DIN-6 PS/ keyboard port

 One game/MIDI port

 Three audio jacks: line-out, line-in and mic-in

Connectors

 One connector for additional external USB ports

 One 9-pin connector for 1 external serial port

 One connector for IrDA interface

 Two IDE connectors

 One floppy drive interface supports up to two .88MB floppy

drives

 One ATX power supply connector

 One Wake-On-LAN connector

 One Wake-On-Ring connector

 CPU and chassis fan connectors

 Two internal audio connectors (AUX-in and CD-in)

 One connector for external line-out and mic-in jacks

Introduction



PCI Bus Master IDE Controller

 Two PCI IDE interfaces suppor t up to four IDE devices

 Supports ATA/33, ATA/66 and ATA/100 hard drives

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-1 0 and ZIP

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the HPSIR and ASKIR

standard.

USB Ports

The system board supports 4 USB ports. Two onboard USB ports

are located at the ATX double deck ports of the board. The J 8

connector on the system board allows you to connect the optional

3rd and 4th USB ports. These optional USB por ts, which are

mounted on a card-edge bracket, will be provided as an option.

USB allows data exchange between your computer and a wide

range of simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows® 95/98/ 000/ME Plug and Play

compatible

 Supports SCSI sequential boot-up

 Flash EPROM for easy BIOS upgrades

 Supports DMI .0 function

 Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI .0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

DFI

DFI CB64-BX Manuel utilisateur

DFI

DFI CR101-D Manuel utilisateur

DFI

DFI CS551-C246 Manuel utilisateur

DFI

DFI PT332-DRM Manuel utilisateur

DFI

DFI CS100 Series Manuel utilisateur

DFI

DFI COM630-B Manuel utilisateur

DFI

DFI 845GV-MLV Manuel utilisateur

DFI

DFI SR330-N Manuel utilisateur

DFI

DFI AZ30-EC Manuel utilisateur

DFI

DFI CMS631-Q470E Manuel utilisateur

DFI

DFI G586IPB Manuel utilisateur

DFI

DFI AD73 Pro Manuel utilisateur

DFI

DFI EL620-C Manuel utilisateur

DFI

DFI SD630-H110 Manuel utilisateur

DFI

DFI G7B630-N Manuel utilisateur

DFI

DFI 915GM-MGF Manuel utilisateur

DFI

DFI 486-OCV Plus Manuel utilisateur

DFI

DFI P4X533-ALE Manuel utilisateur

DFI

DFI M8MP553 Manuel utilisateur

DFI

DFI CS632-C246 Manuel utilisateur

DFI

DFI PB64-BX Manuel utilisateur

DFI

DFI EHL171 Manuel utilisateur

DFI

DFI LanParty DK P35 series Manuel utilisateur

DFI

DFI NFII ULTRA-AL Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur