DFI G586OPC Manuel utilisateur

G586OPC

Rev. 0 +

System Board

User’s Manual

-D28450828-

No part of this document may be copied, reproduced in

any form or by any means or used to make any trans-

formation/adaptation without the prior written consent

of DFI, Inc.

DFI, Inc. makes no warranties with respect to this

documentation and disclaims any implied warranties of

merchantability, quality, or fitness for any particular

purpose. The information in this document is subject to

change without notice. DFI, Inc. reserves the right to

make revisions to this publication and to make changes

to any and/or all parts of its content, at any time,

without obligation to notify any person or entity of such

changes. Further, DFI, Inc. assumes no responsibility

for any errors that may appear in this document.

DFI is a registered trademark, and G586OPC is a

trademark of Diamond Flower, Inc. All other product

names mentioned are trademarks or registered trade-

marks of their respective companies.

vFCC Statement on Class B

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential

installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

the receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modifications not expressly

approved by the party responsible for compliance

could void the user's authority to operate the

equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

v Table of Contentsv

Introduction ..............................................................................

Features and Specifications .........................................

Package Checklist ........................................................

Installation Overview ...............................................................

Preparing the Area ..............................................................

Handling the System Board ................................................

Tips in Handling the System Board ..............................

Hardware Installation...........................................................

Memory Installation .......................................................

Installing the Modules ............................................

Board Configuration ......................................................

Jumper Settings for Display Type and

CMOS Clean ..........................................................

Jumper Settings for Super I/O Setting ..................

Cache Configuration .....................................................

Installing Asynchronous SRAM .............................

Jumper Settings for Cache Memory ...............

256KB Cache SRAM ................................

512KB Cache SRAM ................................

1MB Cache SRAM ...................................

Installing the Synchronous Cache Module .....

Jumper Settings ........................................

Installation .................................................

VRM Header .................................................................

VRM Header and 3.3V Pentium Processor ...........

VRM Header and Future Low-Voltage CPUs ........

CPU Installation ............................................................

Jumper Settings for CPU .......................................

Jumpers JP3, JP4, JP9, JP10, JP18, JP19, JP20

JP21 and JP24 .............................................................

Installing Upgrade CPUs ..............................................

Built-in Ports ........................................................................

Serial Ports ...................................................................

PS/2 Mouse Port ...........................................................

Parallel Port ..................................................................

Floppy Disk Drive Connector ........................................

IDE Hard Disk Interface ................................................

Installing Expansion Cards ..................................................

Installing the System Board ................................................

IDE Device Drivers ..............................................................

Troubleshooting Checklist .....................................................

Appendix A:PCI I/O Pin Assignments ..................................

Appendix B:ISA I/O Pin Assignments ..................................

Appendix C:Connector Pin Assignments ............................

PCI/ISASystemBoard

vIntroduction

The G586OPC system board offers several advanced

features integrated into the system board. Its design is

based on the new Peripheral Component Interconnect

(PCI) local bus and Industry Standard Architecture

(ISA) standards.

The G586OPC provides a 321-pin Zero Insertion Force

(ZIF) CPU socket for PentiumTM processors running at

75MHz, 90MHz, 100MHz, 120MHz, 133MHz or

150MHz frequency. This ZIF socket allows users to

easily upgrade their CPUs. It also provides a VRM

(Voltage Regulation Module) header allowing you to

upgrade to future low-voltage CPUs.

The G586OPC is equipped with three PCI slots, three

ISA slots and one shared PCI/ISA slot.

The G586OPC board has two bus master PCI IDE

connectors. Bus mastering reduces CPU use during disk

transfer. The system board is also equipped with two

NS16C550A-compatible serial ports, an SPP/EPP/ECP

parallel port, a floppy disk drive controller, one PS/2

mouse port and one PS/2 keyboard connector.

The G586OPC can support 2MB to 128MB of memory

using 256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 and

8Mx36 72-pin SIM modules.

G586OPC

Features and Specifications

Processor

•Intel PentiumTM 75/90/100/120/133/150MHz

•Future Pentium Processor and Pentium OverDrive

Processor

Chipset

•OPTI Viper-M chipset

Energy Efficient Design

•Supports System Power Management

•CPU stopped clock control

•Hardware supports SMI green mode

•Microsoft/Intel APM 1.1 compliant

Two Bus Master PCI IDE Connectors

•PIO Modes 3 & 4 Enhanced IDE (data transfer rate

up to 16.6MB/sec)

•DMA Mode 2 Bus Master IDE (data transfer rate

up to 22.2MB/sec)

•Bus mastering reduces CPU use during disk

transfer

•ATAPI IDE CD-ROM supported

Integrated I/O

•Super I/O controller: SMC FDC37C665GT,

SMC FDC37C669GT or

UMC8669

•Two NS16C550A-compatible high speed UARTs

•One SPP/EPP/ECP parallel port

•One 720KB/1.2MB/1.44MB/2.88MB floppy

controller

•PS/2 mouse port

•PS/2 keyboard connector or AT keyboard

connector

PCI/ISASystemBoard

BIOS

•Award Plug & Play BIOS

•Supports Enhanced IDE devices

•Supports Enhanced IDE HDDs larger than 528MB

(LBA mode only)

Architecture

•PCI/ISA

Cache

•256KB, 512KB or 1MB direct map write-back or

write-through cache

•32Kx8, 64Kx8 or 128Kx8 asynchronous SRAM

(supports 5V/3.3V mixed voltage SRAM)

•160-pin cache module upgrade slot for optional

synchronous pipeline burst cache module

Memory

•2MB to 128MB onboard memory

•Four 72-pin SIMM sockets

•Supports single and/or double density SIMMs

•256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 or

8Mx36 parity SIMMs

•x32 non-parity SIMMs supported

•Supports 60ns or 70ns fast page mode DRAM or

EDO DRAM

Expansion Slots

•Three dedicated PCI slots

•One shared PCI/ISA slot

•Three dedicated 16-bit ISA slots

With the optional synchronous pipeline burst

cache module installed in the 160-pin cache

module upgrade slot, the length of the add-in card

in PCI Slot 2 is limited to 124,65 mm.

G586OPC

VRM and ZIF Sockets

•VRM (Voltage Regulation Module) header

allows upgrade to future low-voltage CPUs

•321-pin ZIF socket (Intel Socket 7)

Board Dimensions

•28cm (11.02") x 22cm (8.58")

PCI/ISASystemBoard

Package Checklist

The G586OPC package contains the following items:

•The G586OPC system board

•The G586OPC user’s manual

•One set of IDE driver diskettes

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port

cables

If any of these items is missing or damaged, please

contact your dealer or sales representative for assistance.

Table des matières

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur