DFI G586OPB Manuel utilisateur
G586OPB
Rev. 0 +
System Board
User’s Manual
-D27850601-
vCopyright1995byDFI,Inc.
All rights reserved.
No part of this document may be copied, reproduced in
any form or by any means or used to make any trans-
formation/adaptation without the prior written consent
of DFI, Inc.
DFI, Inc. makes no warranties with respect to this
documentation and disclaims any implied warranties of
merchantability, quality, or fitness for any particular
purpose. The information in this document is subject to
change without notice. DFI, Inc. reserves the right to
make revisions to this publication and to make changes
to any and/or all parts of its content, at any time,
without obligation to notify any person or entity of such
changes. Further, DFI, Inc. assumes no responsibility
for any errors that may appear in this document.
DFI is a registered trademark, and G586OPB is a
trademark of Diamond Flower, Inc. All other product
names mentioned are trademarks or registered trade-
marks of their respective companies.
vFCC Statement on Class B
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
the receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio TV
technician for help.
Notice:
1. The changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
2. Shielded interface cables must be used in order to
comply with the emission limits.
v Table of Contentsv
Introduction ..............................................................................
Features and Specifications .........................................
Package Checklist ........................................................
Installation Overview ...............................................................
Preparing the Area ..............................................................
Handling the System Board ................................................
Tips in Handling the System Board ..............................
Hardware Installation...........................................................
Memory Installation .......................................................
Installing the Modules ............................................
Board Configuration ......................................................
Jumper Settings for Flash EPROM, PS/2 Mouse
and Display Type....................................................
Jumper Settings for Parallel Port ...........................
Cache Configuration .....................................................
Jumper Settings for Cache Memory ......................
CPU Installation ............................................................
Jumper Settings for CPU .......................................
Installing Upgrade CPUs .......................................
Built-in Ports ........................................................................
Serial Ports ...................................................................
Parallel Port ..................................................................
Floppy Disk Drive Connector ........................................
IDE Hard Disk Connector .............................................
PS/2 Mouse Port ...........................................................
Installing Expansion Cards ..................................................
Installing the System Board ................................................
1-1
1-2
1-5
2-1
2-1
2-2
2-2
2-3
2-3
2-6
2-7
2-8
2-11
2-13
2-14
2-17
2-18
2-21
2-26
2-27
2-28
2-30
2-31
2-34
2-35
2-36
3-1
3-2
3-2
3-5
3-7
3-8
3-9
3-16
3-17
3-17
3-18
3-19
3-20
4-1
5-1
A-1
B-1
C-1
D-1
E-1
F-1
G-1
Initial Setup Program ..............................................................
Award BIOS CMOS Setup Utilities .....................................
Standard CMOS Setup .................................................
BIOS Features Setup ....................................................
Chipset Features Setup ................................................
Power Management Setup ...........................................
PCI Configuration Setup ...............................................
Load BIOS Defaults ......................................................
Load Setup Defaults .....................................................
Password Setting ..........................................................
IDE HDD Auto Detection ..............................................
Save & Exit Setup .........................................................
Exit Without Saving .......................................................
IDE Device Drivers ..................................................................
Troubleshooting Checklist .....................................................
Appendix A:Types of Modules ..............................................
Appendix B:System Error Report .........................................
Appendix C:Memory & I/O Maps ..........................................
Appendix D:PCI I/O Pin Assignments ..................................
Appendix E:ISA I/O Pin Assignments ..................................
Appendix F:Connector Pin Assignments ............................
Appendix G:Award BIOS Hard Disk Table ...........................
PCI/ISASystemBoard
1-1 uIntroduction
vIntroduction
The G586OPB system board offers several advanced
features integrated into the system board. Its design is
based on the new Peripheral Component Interconnect
(PCI) local bus and Industry Standard Architecture
(ISA) standards.
The G586OPB supports a 321-pin Zero Insertion Force
(ZIF) CPU socket for PentiumTM processors running at
75MHz, 90MHz, 100MHz, 120MHz, 133MHz or
150MHz frequency. This ZIF socket allows users to
easily upgrade their CPUs. It also supports a Flash
EPROM for easy BIOS upgrades. Flash EPROM is a
memory chip for the storage of BIOS which can be
erased in bulk or modified using a software utility.
The G586OPB is equipped with three PCI slots, three
ISA slots and one shared PCI/ISA slot.
Equipped with two built-in PCI IDE connectors, the
G586OPB system board can control four drives and
supports fast Mode 3 and 4 hard drives and hard drives
larger than 528MB under DOS. The system board is
also equipped with two NS16C550A-compatible serial
ports, an ECP/EPP parallel port, a floppy disk drive
controller, and one mini-DIN-6 connector for the PS/2
mouse.
The G586OPB can support 2MB to 128MB of memory
using 256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 and
8Mx36 72-pin SIM modules.
G586OPB
Features and Specifications
Introduction u1-2
Processor
•Intel PentiumTM 75/90/100/120/133/150MHz
Chipset
•OPTI: Viper chipset
Energy Efficient Design
•Supports 3.3V CPUs
•Supports system power management
•Supports CPU stopped clock
Power Management
•Three power-saving stages: Doze, Standby and
Suspend
•Microsoft APM 1.1 supported
PCI IDE Interface
•Fast PCI local-bus interface
•Supports Mode 3, 4 Enhanced IDE
•Two IDE connectors to control four drives (e.g.
two HDDs, one tape drive and one CD-ROM)
Super I/O Interface
•Two NS16C550A-compatible serial ports
•PS/2 mouse port
•One parallel port with EPP and ECP support
•Supports 360KB, 720KB, 1.2MB, 1.44MB and
2.88MB floppy drives
•Uses NS PC87332VF super-I/O controller
BIOS
•Award Flash BIOS supports Windows 95 Plug &
Play
•Supports enhanced IDE larger than 528MB under
DOS (LBA mode only)
PCI/ISASystemBoard
1-3 uIntroduction
Architecture
•PCI/ISA
Cache Memory
•256K, 512K or 1MB direct map write-back or
write-through cache
•Uses 32Kx8, 64Kx8 or 128Kx8 SRAM
•Supports 3.3V or 3.3V/5V mixed voltage SRAM
Memory Onboard
•Up to 128MB
•Four 72-pin SIMM sockets
•Supports single and/or double density SIMMs
•256Kx36, 512Kx36, 1Mx36, 2Mx36, 4Mx36 or
8Mx36 SIMMs
•Supports 60ns or 70ns fast page mode DRAM or
EDO DRAM
Expansion Slots
•Three dedicated PCI slots
•One shared PCI/ISA slot
•Three dedicated 16-bit ISA slots
Due to the height of the heat sink, once the 3.3V
Pentium Upgrade Processor is in place, you cannot
install full-length add-in cards in slot connectors 1,
2 and 4 (ISA), and 1 and 2(PCI). These slots are
limitted to 2/3 length of add-in cards.
ZIF Socket
•321-pin ZIF socket (Intel Socket 7)
Board Dimensions
•33cm (12.87") x 22cm (8.58")
Baby AT form factor
G586OPB
Package Checklist
The G586OPB package contains the following items:
•The G586OPB system board
•The G586OPB user’s manual
•One set of IDE driver diskettes
•One 34-pin floppy disk drive cable
•Two 40-pin IDE hard disk cables
•One 25-pin printer port cable for chassis mounting
•One card-edge bracket with serial and mouse port
cables
If any of these items are missing or damaged, please
contact your dealer or sales representative for assistance.
Introduction u1-4
PCI/ISASystemBoard
vInstallation Overview
This chapter summarizes the steps in installing the
G586OPB system board into your system unit. It also
includes a description of the area in which you must
work and directions for memory installation. Before
installing the system board, obtain the memory you plan
to install. Please refer to the memory chart, on pages 2-3
and 2-4, for the number and type of SIM modules
needed for the amount of memory you require.
Preparing the Area
Before unpacking the system board, make sure the
location you have selected is relatively free of dust and
static electricity. Excessive exposure to dust, static
electricity, direct sunlight, excessive humidity, extreme
cold, and water can damage the operational capabilities
of your system board. Avoid placing the unit on soft
surfaces such as beds and carpeted floors which can
hinder air circulation. These areas also attract static
electricity which can damage some circuits on your
system board.
Make sure that the power source has a properly
grounded, three-pronged socket. It is essential that the
power connection be properly grounded for correct
functioning of your system board. For further protection,
we recommend that you use a surge suppressor. This
will protect the system board from damage that may
result from a power surge on the electrical line.
Move items that generate magnetic fields away from
your system board, since magnetic fields can also
damage your system board. Once you have selected the
2-1 uInstallation Overview
Table des matières
Autres manuels DFI Carte mère
DFI
DFI lanparty UT nF3 250Gb Manuel utilisateur
DFI
DFI 915G-TMGF Manuel utilisateur
DFI
DFI LanParty nF4 Manuel utilisateur
DFI
DFI G586SPB AIO Manuel utilisateur
DFI
DFI CMS630-Q470ECRM Manuel utilisateur
DFI
DFI CS65-EC Manuel utilisateur
DFI
DFI PIC-Q170 Manuel utilisateur
DFI
DFI G586IPBS Manuel utilisateur
DFI
DFI KD632-Q170 Manuel utilisateur
DFI
DFI MB330-CRM Manuel utilisateur
DFI
DFI G586VPS Pro Manuel utilisateur
DFI
DFI CA64-TN Manuel utilisateur
DFI
DFI PR611-C621 Manuel utilisateur
DFI
DFI KM400A-MLV Manuel utilisateur
DFI
DFI SD631-C236 Manuel utilisateur
DFI
DFI LanParty UT NF590 SLI-M2R/G Manuel utilisateur
DFI
DFI NB76-TC Manuel utilisateur
DFI
DFI C586HX Manuel utilisateur
DFI
DFI G4V100-P Manuel utilisateur
DFI
DFI 586ITB Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
