DFI CS15-BN Manuel utilisateur

CS15 Series

Rev.A+

System Board

User’s Manual

49000116

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,

Windows®98 SE, Windows®ME, Windows®2000 and Windows

NT®4.0 are registered trademarks of Microsoft Corporation. Intel®,

Pentium®III and CeleronTM are registered trademarks of Intel

Corporation. VIA CyrixIII is a registered trademark of VIA

Technologies, Inc. Award is a registered trademark of Award

Software, Inc. Other trademarks and registered trademarks of

products appearing in this manual are the properties of their

respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to the battery

manufacturer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout ..........................................................................................

2.2 System Memory...........................................................................................................

2.3 Jumper Settings for Clearing CMOS Data........................................

2.4 Ports and Connectors...........................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Features.............................................................

3.1.2 Advanced BIOS Features..............................................................

3.1.3 Advanced Chipset Features ......................................................

3.1.4 Integrated Peripherals.........................................................................

3.1.5 Power Management Setup............................................................

3.1.6 PnP/PCI Configurations....................................................................

3.1.7 PC Health Status...................................................................................

3.1.8 Frequency/Voltage Control............................................................

3.1.9 Load Fail-Safe Defaults.....................................................................

3.1.10 Load Optimized Defaults..............................................................

3.1.11 Set Supervisor Password...............................................................

3.1.12 Set User Password..............................................................................

3.1.13 Save & Exit Setup.................................................................................

3.1.14 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

Appendix A - System Error Messages

A.1 POST Beep.......................................................................................................................

A.2 Error Messages..............................................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist....................................................................................

Appendix C - Watchdog Timer

C.1 WatchdogTimer..............................................................................................................

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• Intel®815E

Processor

The system board is equipped with Socket 370. It is also equipped

with a switching voltage regulator that automatically detects 1.30V

to 2.05V.

• Pentium®III FCPGA 133MHz FSB (533EB-1GHz) or 100MHz

FSB (500E-850E) processor

• CeleronTM 66MHz FSB: FCPGA (566MHz-700MHz) or PPGA

(300A-533MHz) processor

• FutureVIA CyrixIII processor

System Memory

• 32MB to 512MB memory using unbuffered DIMMs

• Two 144-pin stacked SODIMM

• Uses x64 PC-133/PC-100 SDRAM DIMM (3.3V) for 133MHz/

100MHz system memory bus

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

16MBx64

32MBx64

Memory Size

16MB

32MB

64MB

128MB

256MB

Introduction

Expansion Slots

The CS15-BN system board is not equipped with any expansion

slots.

The CS15-SN system board is equipped with a 90oPCI slot

located on the solder side of the board.

The CS15-EN system board is equipped with a riser card slot

located on the solder side of the board for connecting a 3-PCI-slot

riser card (the riser card is optional).

Onboard Graphics Features

• Graphics memory

- Shares 1MB of the system memory. This is fixed regardless of

the size of the system memory.

- Uses the Dynamic Video Memory Technology (DVMT) tech-

nology. This freely changes in size because graphics memory is

allocated from the system memory according to current

needs.

• Graphics controller

- 3D hyper pipelined architecture

- 2D hardware and motion video acceleration

- 9-bit precision hardware motion compensation assistance for

software MPEG2 decode

- Software DVD at 30fps

• 2D graphics features

- Resolution: up to 1600x1200 in 8-bit color at 85Hz refresh

- 3 Operand Raster BitBLTs

- 64x64x3 color transparent cursor

• 3D graphics features

- Flat and Gouraud shading

- MIP mapping with tri-linear and anisotropic filtering

- Full color specular / Z-buffering

- Fogging atmospheric effect

- 3D pipe 2D clipping / backface culling

• Software drivers

- Windows®95/98/2000

- Windows NT®4.0

Introduction

Compatibility

• Microsoft PC ’99 compliant

• VESA Display Power Management Signaling (DPMS)

• VESA DDC2B for Plug and Play monitors

• PCI 2.2 compliant

ATX Double Deck Connectors

• 2 USB ports

• 1 DB-9 serial port

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 1 DB-15VGA port

• 3 RJ45 LAN ports

Connectors

• 1 9-pin connector for 1 external serial port

• 2 IDE connectors (90O)

• 1 floppy connector

• 1 power board connector

• 2 connectors for CPU and chassis fans

Power Boards

• CS15-BN

Uses ATX power board which is compatible with ATX switching

power

• CS15-SN

Uses DC-DC power board: +12V input over 110W adapter

with 4 defined pins

• CS15-EN

Uses ATX power board which is compatible with ATX switching

power

PCI Bus Master IDE Controller

• Two PCI IDE interfaces support up to four IDE devices

• Supports ATA/33, ATA/66 and ATA/100 hard drives

• PIO Mode 4 Enhanced IDE (data transfer rate up to 14MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

Introduction

USB Ports

The system board is equipped with 2 USB ports. USB allows data

exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®95/98/2000 Plug and Play compatible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades (4Mbit)

• Includes Symbios Logic SCSI BIOS

• Supports DMI 2.0 function

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS.The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to chapter 4 for instructions on using

the DMI utility.

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following “system

health” conditions.

• Monitors CPU/system temperature and overheat alarm

• Monitors 5VSB/VBAT/1.5V/3.3V/5V/±12V/CPU voltages and

failure alarm

• Monitors the fan speed of the CPU, chassis and second fans;

and failure alarm

• Automatic CPU and chassis fans on/off control

• Read back capability that displays temperature, voltage and fan

speed

• Supports Intel®processor thermal diode output (real processor

temperature)

Refer to the “PC Health Status” section in chapter 3 for more

information.

Introduction

1.1.3 Intelligence

Watchdog Timer

The system board supports the Watchdog Timer function. It allows

your application to regularly “clear” the system at the set time

interval. If the system hangs or fails to function, it will reset at the set

time interval so that your system will continue to operate. Refer to

WatchdogTimer in appendix C for more information.

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system

enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the “Soft-Off By PWR-BTTN” field of

the Power Management Setup, this switch will allow the system to

enter the Soft-Off or Suspend mode.

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or PS/2 mouse to

power-on the system. Refer to “Keyboard/Mouse Power On” in the

Integrated Peripherals section in chapter 3 for more information.

Important:

• The power button will not function once a keyboard

password has been set in the “KB Power On Password”

field of the Integrated Peripherals submenu. You must type

the correct password to power-on the system. If you forgot

the password, power-off the system and remove the

battery. Wait for a few seconds and install it back before

powering-on the system.

• The 5VSB power source of your power supply must

support

≥

720mA.

RTCTimer to Power-on the System

The RTC installed on the system board allows your system to

automatically power-on on the set date and time. Refer to “Resume

By Alarm” in the Power Management Setup section in chapter 3 for

more information.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur