DFI P5BV3+ Manuel utilisateur

355B0912

P5BV3+

Rev. C+

System Board

Users Manual

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95 and Windows®98

are registered trademarks of Microsoft Corporation. Intel, Pentium

and Pentium with MMX technology are registered trademarks of

Intel Corporation. Cyrix, 6x86L, 6x86MX and M II are registered

trademarks of Cyrix Corporation. AMD, K5, K6, K6-2 and K6-III are

registered trademarks of Advanced Micro Devices, Inc. IBM 6x86MX

is a registered trademark of International Business Machine

Corporation. IDT C6, WinChip2 and WinChip3 are registered

trademarks of IDT Corporation. Award is a registered trademark of

Award Software, Inc. Other trademarks and registered trademarks

of products appearing in this manual are the properties of their

respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to tr y to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .............................................................................................

2.2 System Memory.............................................................................................................

2.3 DIP Switch and Jumper Settings of the Processors...................

2.4 Jumper Settings for Clearing CMOS Data..........................................

2.5 Jumper Settings for SDRAM Clock (DIMM)......................................

2.6 Connecting the Ribbon Cables and Wires of the Ports

and Connectors.............................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Setup....................................................................

3.1.2 BIOS Features Setup..........................................................................

3.1.3 Chipset Features Setup....................................................................

3.1.4 Power Management Setup............................................................

3.1.5 PNP/PCI Configuration....................................................................

3.1.6 Load Fail-Safe Settings......................................................................

3.1.7 Load Optimal Settings......................................................................

3.1.8 Integrated Peripherals.........................................................................

3.1.9 Supervisor Password..........................................................................

3.1.10 User Password.........................................................................................

3.1.11 IDE HDD Auto Detection...........................................................

3.1.12 Save & Exit Setup.................................................................................

3.1.13 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface....................................................................

4.2 System Health Monitor Utility..........................................................................

4.3 Drivers...................................................................................................................................

Appendix A - Identifying Processors

A.1 Intel Processors.............................................................................................................

A.2 Cyrix Processors..........................................................................................................

A.3 IBM Processors.............................................................................................................

A.4 AMD Processors.........................................................................................................

A.5 IDT Processors.............................................................................................................

Appendix B - System Error Message

B.1 POST Beep.......................................................................................................................

B.2 Error Messages..............................................................................................................

Appendix C - Troubleshooting

C.1 Troubleshooting Checklist.................................................................................... 63

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

 VIA



Apollo 598MVP AGP system chipset

Processor

The system board is equipped with a switching voltage regulator

that supports 2.0V to 3.5V core voltage for various processors.

 AMD®K5 PR90/PR100/PR120/PR133/PR166, K6-166/200/233/

266/300, K6-2/250/266/300/333/350/366/380/400/450 or

K6-III/400

 Intel Pentium



90/100/120/133/150/166/200MHz or Intel

Pentium



processor with MMXTM technology-166/200/233MHz

 Cyrix®6x86L PR150+/PR166+/PR200+, 6x86MX-PR166/

PR200/PR233/PR266 or M II-200/266/300/333/366/380/400

 IBM® 6x86MX-PR200/PR233/PR266/PR300/PR333

 IDT®C6-180/200/225/240, WinChip2-200/225/233/240/266/

300 or future WinChip3 series

System Memory

 16MB to 384MB memory using unbuffered DIMMs

 Three 168-pin DIMM sockets using x64 SDRAM, 3.3V

 PC-100 SDRAM DIMM for 100MHz external system bus clock

processors

Chapter 1 - Introduction

DIMMs

2MBx64

4MBx64

8MBx64

16MBx64

Memory Size

16MB

32MB

64MB

128MB

Introduction

Level 2 Cache Memory

 512KB or 1MB pipeline burst, direct map write-through cache

installed on the system board.

Expansion Slots

The system board is equipped with 1 dedicated AGP slot, 3

dedicated PCI slots, 2 dedicated 16-bit ISA slots and 1 shared PCI/

ISA slot. All PCI and ISA slots are bus masters.

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

Connectors

 2 connectors for external USB ports

 1 connector for IrDA interface

 2 serial ports

 1 parallel port

 2 IDE connectors

 1 floppy connector

 1 PS/2 mouse port

 1 PS/2 or AT keyboard port

 1 20-pin ATX power supply connector

 1 12-pin standard AT power supply connector

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Ultra DMA/33 supported (Synchronous Ultra DMA mode -

data transfer rate up to a maximum of 33MB/sec.)

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

Introduction

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120, ZIP and SCSI sequential

boot-up

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports infrared peripheral devices that meet the ASKIR or HPSIR

standard.

USB Ports

The system board is equipped with two connectors for external

USB ports. USB allows data exchange between your computer and

a wide range of simultaneously accessible external Plug and Play

peripherals.

BIOS

 Award BIOS, Windows



95/98 Plug and Play compatible

 Flash EPROM for easy BIOS upgrades

 Flash memory

The system board comes standard with 1MB flash memory. An

optional 2MB flash memory, which includes the ACPI and SDMS

functions, will be provided only upon request.

1.1.2 Intelligence

Monitors Processor Temperature and Overheat Alarm

The system board is able to detect the temperature of the

processor. An alarm will sound in case of processor overheat.

Monitors Processor/AGP Fan Speed and Failure Alarm

The system board is able to detect the fan speed (RPM-Revolutions

Per Minute) of the processor and AGP fans, and alerts you to attend

to any irregularity that may damage your system.

Monitors Power Voltages and Failure Alarm

The system board is able to detect the output voltage of the power

supply. An alarm will sound warning you of voltage irregularity.

Introduction

Automatic Fan Control

With the systems power switched on, the processors fan will rotate

only if the temperature of the processor is over 25oC.

Dual Function Power Button (ATX power supply only)

Depending on the setting in the BIOS setup, this switch will allow

your system to enter the Soft-Off or Suspend mode.

External Modem Ring-on (ATX power supply only)

The Modem Ring-on feature allows the system that is in the

Suspend mode or Soft Power Off mode to wake-up/power-on to

respond to incoming calls.

Note:

This feature supports external modem only. If you are using

this function, make sure to turn on the power of the modem

prior to powering-off the system.

RTC Timer to Power-on the System (ATX power supply only)

The RTC installed on the system board allows your system to

automatically power-on on the set date and time.

ACPI (ATX power supply only)

The system board is designed to meet the ACPI (Advanced

Configuration and Power Interface) specification. ACPI has energy

saving features that enables PCs to implement Power Management

and Plug-and-Play with operating systems that support OS Direct

Power Management.

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table of

your hard disk drive.

Introduction

1.2 Package Checklist

The system board package contains the following items:

þThe system board

þA users manual

þSerial, mouse and printer por t cables

Option 1:

- One card-edge bracket with a 9-pin and 25-pin serial port

cables

- One card-edge bracket with a 25-pin printer port cable and

a PS/2 mouse port cable

Option 2:

- One card-edge bracket with two 9-pin serial port cables

and a PS/2 mouse port cable

- One 25-pin printer port cable for chassis mounting

þOne 40-pin IDE hard disk cable

þOne 34-pin floppy disk drive cable

þOne CD

¨One card-edge bracket with two USB ports (optional)

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur