DFI 661FX-MLV Manuel utilisateur

661FX-MLV

661FX-MLVE

Rev. C+

System Board

User’s Manual

76120410

This publication contains information that is protected by copy-

right. No part of it may be reproduced in any form or by any

means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with re-

spect to the contents or use of this manual and specifically dis-

claims any express or implied warranties of merchantability or

fitness for any particular purpose. The user will assume the entire

risk of the use or the results of the use of this document. Further,

the manufacturer reserves the right to revise this publication and

make changes to its contents at any time, without obligation to

notify any person or entity of such revisions or changes.

Trademarks

Windows®98, Windows®98 SE, Windows®ME, Windows®2000,

Windows NT®4.0 and Windows®XP are registered trademarks

of Microsoft Corporation. Intel®and Pentium®4 are registered

trademarks of Intel Corporation. Award is a registered trademark

of Award Software, Inc. Other trademarks and registered trade-

marks of products appearing in this manual are the properties of

their respective holders.

Caution

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servic-

ing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

by the manufacturer.

• Dispose of used batteries according to the battery manufac-

turer’s

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

residential installation. This equipment generates, uses and can ra-

diate radio frequency energy and, if not installed and used in ac-

cordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's author-

ity to operate the equipment.

2. Shielded interface cables must be used in order to comply

with the emission limits.

Notice

This user’s manual contains detailed information about the system

board. If, in some cases, some information doesn’t match those

shown in the multilingual manual, the multilingual manual should

always be regarded as the most updated version. The multilingual

manual is included in the system board package.

To view the user’s manual, insert the CD into a CD-ROM drive.

The autorun screen (Mainboard Utility CD) will appear. Click the

“TOOLS” icon then click “Manual” on the main menu.

System Board

This user’s manual is for the 661FX-MLV and 661FX-MLVE system

boards. The only difference between these boards is the

661FX-MLV system board is equipped with 2 SATA connectors

that support RAID function.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..............................................................................

1.2 Hyper-Threading Technology Functionality Require-

ments.........................................................................................................................................

1.3 Package Checklist.....................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .........................................................................................

2.2 System Memory..........................................................................................................

2.3 CPU...........................................................................................................................................

2.4 Jumper Settings............................................................................................................

2.5 Rear Panel I/O Ports.............................................................................................

2.6 I/O Connectors...........................................................................................................

Chapter 3 - BIOS Setup

3.1 Award BIOS Setup Utility..................................................................................

3.2 Updating the BIOS.....................................................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface..................................................................

4.2 Drivers, Utilities and Software Applications.................................

4.3 Installation Notes.........................................................................................................

103

Introduction

Appendix A - Enabling the Hyper-Threading

Technology

A.1 Enabling the Hyper-Threading Technology...................................

Appendix B - Using the Suspend to RAM

Function

B.1 Using the Suspend to RAM Function...............................................

Appendix C - System Error Messages

C.1 POST Beep..................................................................................................................

C.2 Error Messages..........................................................................................................

Appendix D - Troubleshooting

D.1 Troubleshooting Checklist..............................................................................

104

107

111

113

Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• 661FX-MLV

- North bridge: SiS®661FX

- South bridge: SiS®964

• 661FX-MLVE

- North bridge: SiS®661FX

- South bridge: SiS®964L

Processor

The system board is equipped with Socket 478 for installing one

of the following supported processors.

• Intel®Pentium®4 (Prescott and Northwood) processor up to

3.06GHz

- Intel Hyper-ThreadingTechnology

- FSB: 533MHz and 800MHz

• Intel®Celeron®processor

- 400MHz system data bus

System Memory

• Two 184-pin DDR DIMM sockets

• Supports 4 banks up to 2GB using PC1600 (DDR200),

PC2100 (DDR266), PC2700 (DDR333) and PC3200

(DDR400) unbuffered DDR SDRAM DIMM, 2.6V type

• 16Mb, 64Mb, 128Mb, 256Mb and 512Mb SDRAM technology

with page size from 2KB up to 16KB

Expansion Slots

• 1 AGP slot

• 3 PCI slots

Chapter1 -Introduction

Introduction

AGP (Accelerated Graphics Port)

AGP is an interface designed to support high performance 3D

graphics cards. It utilizes a dedicated pipeline to access system

memory for texturing, z-buffering and alpha blending. The univer-

sal AGP slot supports AGP 8x with up to 2132MB/sec. bandwidth

and AGP 4x with up to 1066MB/sec. bandwidth for 3D graphics

applications. AGP in this system board will deliver faster and bet-

ter graphics to your PC.

Onboard Graphics Features

• Bi-directional 16-bit data bus

• Performs 1GB/s bandwidth in 133MHz x 4 mode

• 3D graphics accelerator

- Built-in high performance 256-bit 3D engine

- Supports Ultra-AGPIITM up to 2.7GB/s bandwidth

- Up to 166MHz 3D engine clock speed

• 2D graphics accelerator

- Built-in hardware command queue

- Supports memory-mapped, zero wait-state, burst engine

write

- Maximum 128MB frame buffer with linear addressing

Onboard Audio Features

• AC'97 2.2 extension compliant codec

• Supports Microsoft®DirectSound/DirectSound 3D

• AC’97 supported with full duplex, independent sample rate

converter for audio recording and playback

• S/PDIF-in/out interface

• 6-channel audio output

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital

audio signals to a device without having to be converted first to

an analog format. This prevents the quality of the audio signal

from degrading whenever it is converted to analog. S/PDIF is usu-

ally found on digital audio equipment such as a DAT machine or

audio processing device. The S/PDIF connector on the system

board sends surround sound and 3D audio signal outputs to am-

Introduction

plifiers and speakers and to digital recording devices like CD re-

corders.

6-channel Audio

The 6-channel audio output function is supported by using the

audio jacks at the rear panel and configuring the audio driver.

Please refer to chapters 2 and 4

Onboard LAN Features

• Phy fast ethernet controller

• Integrated IEEE 802.3, 10BASE-T and 100BASE-TX compatible

PHY

• 32-bit PCI master interface

• Integrated power management functions

• Full duplex support at both 10 and 100 Mbps

• Supports IEEE 802.3u auto-negotiation

• Supports wire for management

SATA IDE Interface with RAID (661FX-MLV only)

Serial ATA is a storage interface that is compliant with SATA 1.0

specification. With speed of up to 1.5Gbps, it improves hard drive

performance even in data intensive environments such as audio/

video, consumer electronics and entry-level servers.

• Supports two SATA (Serial ATA) interfaces which are compli-

ant with SATA 1.0 specification (1.5Gbps interface)

• Supports RAID 0, RAID 1 and JBOD

PCI Bus Master IDE Controller

• Supports ATA/33, ATA/66, ATA/100 and ATA/133 hard drives

• UDMA Modes 3, 4, 5 and 6 Enhanced IDE (data transfer rate

up to 133MB/sec.)

• Bus mastering reduces CPU utilization during disk transfer

• Supports ATAPI CD-ROM, LS-120 and ZIP

Introduction

USB Ports

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1

supports 12Mb/second bandwidth while USB 2.0 supports

480Mb/second bandwidth providing a marked improvement in

device transfer speeds between your computer and a wide range

of simultaneously accessible external Plug and Play peripherals.

BIOS

• Award BIOS, Windows®98SE/2000/ME/XP Plug and Play

compatible

• Supports SCSI sequential boot-up

• Flash EPROM for easy BIOS upgrades

• Supports DMI 2.0 function

• 2Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in

the DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier.

Rear Panel I/O Ports (PC 99 color-coded connectors)

• 4 USB 2.0/1.1 ports

• 1 RJ45 LAN port

• 1 DB-9 serial port

• 1 DB-15 VGA port

• 1 DB-25 parallel port

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 3 audio jacks: line-out, line-in and mic-in

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels DFI Carte mère

DFI

DFI ADS630-R680E Manuel utilisateur

DFI

DFI CB60-ZX Manuel utilisateur

DFI

DFI FS053 Manuel utilisateur

DFI

DFI nF4X Infinity Manuel utilisateur

DFI

DFI P5BV3+/e Manuel utilisateur

DFI

DFI 845PE-ML Manuel utilisateur

DFI

DFI CD101-N Manuel utilisateur

DFI

DFI CS620 Manuel utilisateur

DFI

DFI CMS631-Q470E/H420E Manuel utilisateur

DFI

DFI CM100-C Manuel utilisateur

DFI

DFI G586VPM/C Manuel utilisateur

DFI

DFI HD330 Manuel utilisateur

DFI

DFI HD620 Series Manuel utilisateur

DFI

DFI LANParty UT ICFX3200-T2R/G Manuel utilisateur

DFI

DFI G4S601-B Manuel utilisateur

DFI

DFI BL330-BR Manuel utilisateur

DFI

DFI Blood-Iron G41-T33 Manuel utilisateur

DFI

DFI 661GX-MLV Manuel utilisateur

DFI

DFI LanParty UT RDX200 series Manuel utilisateur

DFI

DFI ST2K Series Manuel utilisateur

DFI

DFI CS551-H310 Manuel utilisateur

DFI

DFI CD951-C Series Manuel utilisateur

DFI

DFI G586IPV Manuel utilisateur

DFI

DFI SB601-C Manuel utilisateur

Manuels Carte mère populaires d'autres marques

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur