Dell SC9000 Manuel utilisateur

Dell Storage Center

SC9000 Storage System

Getting Started Guide

Regulatory Model: E31S

Regulatory Type: E31S001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 10

Rev. A00

Setting Up the Storage System

Consider the following best practices before setting up your SC9000 storage system.

• Dell recommends that you use a dedicated SAN network for data transmission when using a Fibre

Channel or iSCSI storage system.

• Always configure redundant data paths to provide alternate paths to and from the host server should

one of the data paths become disabled.

• Before connecting any cables between the storage system and host server or expansion enclosure,

physically label each port and connector.

• Always follow proper power-up and power-down procedures when cycling power across the

network. Verify that critical network components are on separate power circuits.

NOTE: This product is intended for restricted access locations, such as a dedicated equipment

room or equipment closet.

WARNING: If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient temperature. Therefore,

consideration should be given to installing the equipment in an environment compatible with the

maximum ambient temperature (Tma) specified by the manufacturer.

Safety Warnings

The following information only applies to Fibre Channel storage systems.

Laser Radiation for Fibre Channel Storage Systems

CAUTION: Class I laser radiation when open, avoid exposure to beam.

WARNING: Laser radiation, avoid direct exposure to beam.

The unit is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J

for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the

requirements of IEC 60825-1:2007.

Class I laser products are not considered to be hazardous. The laser system and unit are designed so

there is never any human access to laser radiation above a Class I level during normal operation, user

maintenance or prescribed service condition.

Locating Your Service Tag

Your storage system is identified by a unique Service Tag and Express Service Code.

The Service Tag and Express Service Code are found on the front of the system by pulling out the

information tag. Alternatively, the information may be on a sticker on the back of the storage system

chassis. This information is used by Dell to route support calls to the appropriate personnel.

NOTE: The Quick Resource Locator (QRL) code on the information tag is unique to your system.

Scan the QRL to get immediate access to your system information using your smart phone or

tablet.

Other Information You May Need

To install the storage system, you may need the following additional information.

NOTE: See the safety and regulatory information that shipped with your Storage Center

components. Warranty information is included as a separate document.

• The Dell Storage Center System Manager Administrator's Guide describes how to use the Storage

Center System Manager to manage a Storage Center.

• The Dell Enterprise Manager Administrator’s Guide describes how to use Dell Enterprise Manager to

manage multiple Storage Center systems.

Installation and Configuration

Before you begin installation, make sure that the site where you plan to install the storage system has

standard power from an independent source or a rack power distribution unit with a UPS.

In addition, verify that there is space in the rack to install the storage system.

Unpacking Storage Center Equipment

Unpack the storage system and identify the items in your shipment.

Figure 1. SC9000 Storage System Components

• Documentation

• Storage system

• Rack rails

• Front bezel

• Power and network cables (not shown)

Installing the SC9000 Storage System in a Rack

Install the storage system and other Storage Center components in a rack.

NOTE: Mount the storage system in a manner that allows for expansion in the rack and prevents the

rack from becoming top‐heavy.

Figure 2. Install the Storage System in a Rack

Installing the Front Bezel

Install the bezel on the front of the storage system.

1. Hook the right end of the bezel onto the storage system.

Figure 3. Front Bezel

2. Insert the left end of the bezel into the securing slot until the release latch snaps into place.

3. Secure the bezel with the keylock.

Connecting the Power Cables

Connect the power cables to the storage system.

1. Before connecting the power cables, make sure that the power switches on the storage system are

in the OFF position.

2. Connect the power cables to the power supplies in the storage system chassis.

Figure 4. Power Cables

3. Secure each power cable to the storage system chassis using the strain relief fasteners.

4. Plug the other end of the power cables into a grounded electrical outlet or a separate power source

such as an uninterrupted power supply (UPS) or a power distribution unit (PDU).

NOM Information (Mexico Only)

The following information is provided on the device described in this document in compliance with the

requirements of the official Mexican standards (NOM):

Importer: Dell Inc. de México, S.A. de C.V

Paseo de la Reforma 2620-11 ° Piso

Col. Lomas Atlas

11950 México, D.F.

Model number: E31S

Supply voltage: 100–240 VAC

Frequency: 50/60 Hz

Current consumption: 12 A–6.5 A

Technical Specifications

Processor

Processor type Two Intel Xeon processor E5-2600 v3 product

family

Power

AC power supply unit (PSU) per power supply

Wattage 1100 W

Heat dissipation 4100 BTU/hr maximum (1100 W PSU)

Power

NOTE: Heat dissipation is calculated using

the power supply unit wattage rating.

Voltage 100–240 V AC, autoranging, 50/60 Hz

Expansion Bus

Bus type PCI Express Generation 3

Expansion slots using riser card:

Riser 1 (Slot 1) One half-height, low-profile x8 link

(Slot 2) One half-height, low-profile x8 link

(Slot 3) One half-height, low-profile x8 link

Riser 2 (Slot 4) One full-height, full-length x16 link

(Slot 5) One full-height, full-length x8 link

Riser 3 (Slot 6) One full-height, full-length x8 link

(Slot 7) One full-height, full-length x8 link

Memory

Architecture 2133 MT/s DDR4 registered, load-reduced Error

Correcting Code (ECC) DIMMs

Minimum RAM 128 GB with a single processor

Maximum RAM 256 GB with dual processors

Connectors

Back

NIC Two 1 Gbps plus two 10 Gbps

Serial 9-pin, DTE, 16550-compatible

USB Two 4-pin, USB 3.0-compliant

Video 15-pin VGA

Front

USB One 4-pin, USB 2.0-compliant

One USB management port/iDRAC Direct

Video 15-pin VGA

External vFlash card One flash memory card slot with iDRAC8

Enterprise card

Internal

Connectors

USB One 4-pin, USB 3.0-compliant

Physical

Height 8.73 cm (3.44 inch)

Width 48.2 cm (18.98 inch)

Depth 75.58 cm (29.75 inch)

Maximum configuration

weight

44 lb

Environmental

For additional information about environmental measurements for specific storage system

configurations, see dell.com/environmental_datasheets.

Temperature

Storage –40° to 65°C (–40° to 149°F)

Continuous operation

(for altitude less than

950 m or 3117 ft)

10°C to 35°C with no direct sunlight on the equipment.

Fresh air For information about fresh air, see Expanded Operating Temperature.

Maximum temperature

gradient (operating and

storage)

20°C/h (36°F/h)

Relative humidity

Storage 5% to 95% with 33°C (91°F) maximum dew point. Atmosphere must be non-

condensing at all times.

Operating 10% to 80% with 29°C (84.2°F) maximum dew point

Maximum vibration

Operating 0.26 Grms at 5 Hz to 350 Hz (all operation orientations).

Storage 1.88 Grms at 10Hz to 500 Hz for 15 min (all six sides tested).

Maximum shock

Operating Six consecutively executed shock pulses in the positive and negative x, y, and

z axes of 40 G for up to 2.3 ms.

Storage Six consecutively executed shock pulses in the positive and negative x, y, and

z axes (one pulse on each side of the system) of 71 G for up to 2 ms.

Maximum altitude

Operating 3,048 m (10,000 ft)

Storage 12,000 m (39,370 ft)

Operating temperature de-rating

Environmental

Up to 35 °C (95 °F) Maximum temperature is reduced by 1°C/300 m (1°F/547 ft) above 950 m

(3,117 ft).

35 °C to 40 °C (95 °F to

104 °F)

Maximum temperature is reduced by 1°C/175 m (1°F/319 ft) above 950 m

(3,117 ft).

40 °C to 45 °C (104 °F to

113 °F)

Maximum temperature is reduced by 1°C/125 m (1°F/228 ft) above 950 m

(3,117 ft).

Particulate contamination

NOTE: This section defines the limits to help avoid IT equipment damage and/or failure from

particulates and gaseous contamination. If it is determined that levels of particulates or gaseous

pollution are beyond the limits specified below and are the reason for the damage or failures to

your equipment, it maybe necessary for you to re-mediate the environmental conditions that are

causing the damage or failures. Re-mediation of environmental conditions will be the responsibility

of the customer.

Air filtration Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95%

upper confidence limit.

NOTE: Applies to data center environments only. Air filtration

requirements do not apply to IT equipment designed to be used outside

a data center, in environments such as an office or factory floor.

Conductive dust Air must be free of conductive dust, zinc whiskers, or other conductive

particles.

NOTE: Applies to data center and non-data center environments.

Corrosive dust • Air must be free of corrosive dust.

• Residual dust present in the air must have a deliquescent point less than

60% relative humidity.

NOTE: Applies to data center and non-data center environments.

Gaseous contamination

NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity.

Copper coupon

corrosion rate

<300 Å/month per ClassG1 as defined by ANSI/ISA71.04-1985.

Silver coupon corrosion

rate

<200 Å/month as defined by AHSRAE TC9.9.

Expanded operating temperature

NOTE: When operating in the expanded temperature range, system performance may be impacted.

NOTE: When operating in the expanded temperature range, ambient temperature warnings may be

reported on the LCD and in the system event log.

Continuous operation 5°C to 40°C at 5% to 85% RH with 29°C dew point.

Expanded operating temperature

NOTE: Outside the standard operating

temperature (10°C to 35°C), the system can

operate continuously down to 5°C or as high

as 40°C.

For temperatures between 35°C and 40°C, de-rate

maximum allowable temperature by 1°C per 175m

above 950 m (1°F per 319 ft).

< 1% of annual operating hours –5°C to 45°C at 5% to 90% RH with 29°C dew

point.

NOTE: Outside the standard operating

temperature (10°C to 35°C), the system can

operate down to –5°C or up to 45°C for a

maximum of 1% of its annual operating hours.

For temperatures between 40°C and 45°C, de-rate

maximum allowable temperature by 1°C per 125 m

above 950 m (1°F per 228 ft).

Expanded operating temperature restrictions • Do not perform a cold startup below 5°C.

• The operating temperature specified is for a

maximum altitude of 3050 m (10,000 ft).

• Redundant power supplies are required.

• Peripheral cards that are not Dell-qualified are

not supported.

• Peripheral cards greater than 25 W are not

supported.

Autres manuels pour SC9000

Table des matières

Autres manuels Dell Stockage

Dell

Dell PS Series Manuel utilisateur

Dell

Dell PowerVault MD3800f series Manuel utilisateur

Dell

Dell PowerVault MD1400 Manuel utilisateur

Dell

Dell PowerVault DR4100 Manuel utilisateur

Dell

Dell PowerVault 701N Manuel de l'opérateur

Dell

Dell PowerVault 100T DDS4 Manuel utilisateur

Dell

Dell PowerVault MD3260i Series Guide de référence rapide

Dell

Dell PowerVault MD3220 Series Manuel utilisateur

Dell

Dell NX3230 Manuel utilisateur

Dell

Dell PowerVault 0JC276A02 Manuel utilisateur

Dell

Dell SC5020 Manuel utilisateur

Dell

Dell QLogic Family of Adapters Manuel utilisateur

Dell

Dell EMS01 Manuel utilisateur

Dell

Dell SC7020 Manuel utilisateur

Dell

Dell PowerVault 120T DDS4 Manuel utilisateur

Dell

Dell PowerVault MD3260i Series Mode d'emploi

Dell

Dell PowerVault ML6000 Manuel utilisateur

Dell

Dell PowerVault NX300 Manuel utilisateur

Dell

Dell DR4000 Restore Manager Manuel utilisateur

Dell

Dell PowerVault DL2200 CommVault Manuel utilisateur

Dell

Dell PowerVault 35F Manuel utilisateur

Dell

Dell SC5020 Manuel utilisateur

Dell

Dell PowerVault MD3200i Series Manuel utilisateur

Dell

Dell PowerVault NX400 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur