Datamax M-Class Mark II Manuel utilisateur

Present Sensor Option

92-2476-01 Rev.C

Contents of the Present Sensor Kit

This kit contains the following item:

Present Sensor Option

Follow the steps listed below to install this option.

Step 1: Preparing the Printer

Turn ‘Off’ the power switch and unplug the

printer.

Open the cover. Remove any installed media

from the printer.

Remove the Fascia by gently pulling it forward.

Loosen and remove the Thumbscrew, then

remove the Tear Plate.

Fascia Tear Plate

Thumbscrew

Step 2: Installing the Present Sensor

Position the Present Sensor for mounting on the

front of the printer.

Using the Thumbscrew, secure the Present

Sensor to the printer, as shown.

This completes the installation process.

Proceed to Loading Media.

Thumbscrew

Present Sensor

Loading Media

Load media into the printer as you normally would for tear-off operation (see the Operator’s Manual for

details). When equipped with the Present Sensor option, labels printed in a batch will be dispensed “on-

demand” – that is, printing will occur only after a previously printed label has been removed from the

printer.

Setup, Configuration, and Operation

The Present Sensor is plug and play; no setup or configuration is required. As soon as power is applied, the

printer senses and enables the Present Sensor for operation.

During operation, when a label is present (blocking the sensor), the yellow Stop Light on the front panel of

the printer will flash to prompt you that a label awaits removal.

With printers equipped with an LCD display, the display will read “REMOVE LABEL”

Notes: (1) The operation of the Present Sensor can also be controlled via software commands from the host. Be

sure that your software program is properly configured for use with this option. (2) If the Present Sensor is

disconnected without first powering off the printer, the printer will behave as if there is a label blocking the

sensor. Turn the printer off and then back on. The printer will reconfigure itself to operate without the

Present Option

Present Sensor Maintenance

No regularly scheduled maintenance of the Present Sensor is required, however, for trouble-free operation

be sure to keep the sensor free of debris and dust. To clean the Present Sensor:

CAUTION

For your safety and to avoid damaging the printer, turn ‘Off’ and unplug the printer before cleaning; and

take proper precautions when using isopropyl alcohol, a flammable liquid.

Turn off and unplug the printer. Remove any media.

Using a Cotton Swab or compressed air, wipe or dust

off the Sensors.

(In cases of extreme build-up, a cotton swab

dampened with isopropyl alcohol can be used to

clean the Sensors.)

If alcohol was used, allow the Sensors to dry;

otherwise, go to Step 4.

This completes the cleaning procedure. Reinstall

media. Plug in and turn on the printer.

Sensors

Cotton Swab

Autres manuels pour M-Class Mark II

Table des matières

Autres manuels Datamax Étiqueteuse

Datamax

Datamax Perfomance Series Manuel utilisateur

Datamax

Datamax MICROFLASH 4T Manuel utilisateur

Datamax

Datamax E-Class Mark III Professional+ Manuel utilisateur

Datamax

Datamax Allegro 2 Manuel utilisateur

Datamax

Datamax H-Class Manuel utilisateur

Datamax

Datamax RL3 Manuel utilisateur

Datamax

Datamax E-4304 Manuel utilisateur

Datamax

Datamax RL4e Manuel utilisateur

Datamax

Datamax Prodigy Plus Manuel utilisateur

Datamax

Datamax E Class E-4203 Manuel utilisateur

Datamax

Datamax M-Class Mark II Manuel utilisateur

Datamax

Datamax M-Class Mark II Manuel utilisateur

Datamax

Datamax A-Class A-4212 Manuel utilisateur

Datamax

Datamax E-Class Mark III Manuel utilisateur

Datamax

Datamax Prodigy Manuel utilisateur

Datamax

Datamax I-Class Manuel utilisateur

Datamax

Datamax A-Class Mark II Manuel utilisateur

Datamax

Datamax E-class E-3202 Manuel d'utilisation et d'entretien

Datamax

Datamax I-Class Manuel utilisateur

Datamax

Datamax H-Class Manuel utilisateur

Datamax

Datamax I-Class Mark II Manuel utilisateur

Datamax

Datamax I-Class Mark II I-4212E/203 Manuel utilisateur

Datamax

Datamax M-Class Mark II Manuel utilisateur

Datamax

Datamax I-Class Mark II Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur