Danfoss TP5000 si range Manuel utilisateur

Fig.1

Space for additional

logo if required TP5000

User Instructions

Mon-Fri Sat-Sun

Event Time Temp°C Event Time Temp°C

1 06.30 20 1 07.00 20

2 08.30 15 2 16.00 21

3 11.30 20 3 23.00 15

4 13.30 15 4 00.00 15

5 16.30 21 5 01.00 15

6 22.30 15 6 01.59 15

Fig.2

i2 00

Before programming the thermostat press the + & – AND ∧∧

∧∧

∧and ∨∨

∨∨

∨ buttons

simultaneously to reset the unit (Fig.1)

Setting the Clock and Day

Press PROG (Fig.2) to begin programming

Use + or – buttons (Fig.3) to adjust the TIME (Fig.4)

Press PROG again (Fig.2)

Use + or – buttons (Fig.3) until correct DAY is shown (Fig.5)

(1 = Monday, 2 = Tuesday, etc)

Accepting the Factory Pre-settings

The TP5000 has pre-set times already programmed in, which often suit most

people (see Table below).

To accept these settings close the front cover and after 2 minutes the pre-

settings will automatically be accepted.

To adjust the factory pre-settings & set your own time and

temperature programmes

For Days 1-5 (weekdays)

a) Press PROG (Fig.2) 3 times to show the 1st pre-set time and temperature

(Event 1 Days 1,2,3,4,5) (Fig.6)

b) Use + or – buttons (Fig.3) to adjust the TIME (press and hold to change in

10 min increments)

c) Use ∧∧

∧∧

∧or ∨∨

∨∨

∨ buttons (Fig.7) to adjust the TEMPERATURE

d) Press PROG (Fig.2) to move to next preset time & temp (Event 2) (Fig.8)

e) Repeat steps b, c & d for programming Events 3, 4 5 & 6

For Days 6-7 (weekends)

●Press PROG (Fig.2) to show 1st pre-set time and temperature (Event 1

Days 6-7) (Fig.9)

●Repeat steps b, c and d above to programme time and temperature events

for the weekend

Returning to RUN mode

Press PROG (Fig.2) – the colon in the LCD display will start to flash (Fig.10)

Fig.6

Fig.7

Fig.5

Fig.3

Fig.4

Fig.8

i2 24

12345

6 30

7 00

12345

8 30

Fig.9

Fig.10

Danfoss Randall Ltd

Ampthill Road

Bedford, MK42 9ER

Tel: 01234 364621

Fax: 01234 219705

Email: [email protected]

Website: www.danfoss-randall.co.uk

Fig.14

Fig.16

Fig.12

Fig.13

Fig.11

Temporary User Overrides

The TP5000 has several useful overrides which can be selected without

affecting the thermostat programming

•Selection of time or actual room temperature in main LCD display –

press + and – together to change between settings (Fig.11)

•Temporary override of programmed temperature – press ∧∧

∧∧

∧or ∨∨

∨∨

∨ until

required temperature is displayed (override will automatically cancel at

beginning of next programmed event) (Fig.12)

•Temporary use of weekend programmes – press ∧∧

∧∧

∧and ∨∨

∨∨

∨ together

once (override cancels at 2:00am) (Fig.13)

•Frost Protection – a constant low temperature can be selected whilst

away from home - press ∧∧

∧∧

∧and ∨∨

∨∨

∨ together twice (Fig.14). To return to

automatic programming press ∧∧

∧∧

∧and ∨∨

∨∨

∨ together again

Summer Time / Winter Time Clock

●To change from Summer to Winter (clocks back) -

press and hold - button (Fig.15)

●To change from Winter to Summer (clocks forward) -

press and hold + button (Fig.15)

Battery Replacement

●A low battery symbol will flash in the LCD display (Fig.16)

●You have 15 days to replace the battery before the unit will switch off.

●When changing batteries, remove old batteries and insert new ones within

ONE MINUTE and programming will not be lost.

NB. If the display ever goes blank during normal operation, the batteries will

need to be renewed, the unit reset and the time and programmes reset.

Selection of time

or actual room

temperature

in main LCD

Temporary

override of

programmed

temperature

x 2

03 57

Temporary use

of weekend

programmes

Frost

Protection

Fig.15

Clocks

forward

Clocks

back

Autres manuels pour TP5000 si range

Autres manuels Danfoss Thermostat

Danfoss

Danfoss 088L5130 Manuel utilisateur

Danfoss

Danfoss HC75-1 Manuel d'utilisation

Danfoss

Danfoss RET M Mode d'emploi

Danfoss

Danfoss Link FT Manuel utilisateur

Danfoss

Danfoss DEVI DEVIreg 530 Manuel utilisateur

Danfoss

Danfoss C37 Manuel utilisateur

Danfoss

Danfoss REP24CO Manuel utilisateur

Danfoss

Danfoss KP 61 Manuel utilisateur

Danfoss

Danfoss ECtemp 330 Manuel utilisateur

Danfoss

Danfoss RAS-D2 Combi Manuel utilisateur

Danfoss

Danfoss TP5001RF Manuel utilisateur

Danfoss

Danfoss TP4000 Range Manuel utilisateur

Danfoss

Danfoss Devireg 535 Instructions d'utilisation

Danfoss

Danfoss RET230P Manuel utilisateur

Danfoss

Danfoss HCS6101-3 Instructions d'utilisation

Danfoss

Danfoss 140F1143 Manuel utilisateur

Danfoss

Danfoss TP5001M Manuel utilisateur

Danfoss

Danfoss CFZ Manuel utilisateur

Danfoss

Danfoss FHV-R Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss KPU 61 Manuel utilisateur

Danfoss

Danfoss KPU 19 Manuel utilisateur

Danfoss

Danfoss DEVIreg Smart Manuel utilisateur

Danfoss

Danfoss TPONE-RF Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur