Danfoss HC6110-3 Manuel utilisateur
1
HC6000
GB Installation Instructions
Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Electronic
Programmable
Room Thermostats
Installations vejledning
Installatie handleiding
Montavimo Instrukcija
F
D
ES
DK
NL
Installation Instructions
LT
2
INDEX
Installation Instructions 3-11
Instructions d’installation 12-20
Installationsanweisungen 21-29
Instrucciones de instalación 30-38
Installations vejledning 39-47
Installatie handleiding 48-56
Montavimo Instrukcija 57-65
F
D
ES
DK
NL
GB
LT
3
Installation Instructions
Specication
Installation Instructions
Please note: This product should only be installed by a
qualied electrician or competent heating installer and
should be in accordance with the current edition of the
IEEE wiring regulations.
GB
Features Battery Powered Models 230 Volt Models
Type Code Type Code
Heat and cool systems
(with auto changeover)
for use in 4-pipe systems
HC6110-3 087N705300 HC6113-3 087N705700
HCM6110-3 087N706000 HCM6113-3 087N705600
HCW6110-3 087N706100 HCW6113-3 087N706600
Fan Output 3 speed fan output
Power Supply 2 x AA alkaline batteries
(non-rechargeable)
230 Vac ±15%, 50/60Hz
Temperature Range Heating stage - O - 5-30°C
Cooling stage - 16-37°C - O
Temperature Accuracy ± 0.5°C
Deadzone Adjustment 1, 2, 3 or 4°C
Voltage rating of contacts 20-250 Vac, 50/60Hz
Current rating of contacts 10mA - 3A resistive, 1A inductive
Switching Action Voltage free SPDT contacts, Type 1B
Time Accuracy ± 1 minute
Memory Retention 1 min. for battery change 15 days
IP Rating IP30
Dimensions (mm) 130 x 100 x 38 (W x H x D)
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5 KV
Ball Pressure Test 75°C
Application
4
Installation Instructions
Installation
First remove the wallplate from the back of the unit.
From the top left hand corner of the wallplate, there must be
clearances of at least 140mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-
in module.
Fix at a height of approximately 1.5m from the oor, away
from draughts or heat sources such as radiators, open res
or direct sunlight.
Fit the thermostat to the wall and ensure the maximum cable
size is 1.5mm2.
GB
5
Installation Instructions
GB
Thermostat Wiring
HC Models with 3 speed fan (4 pipe auto change-over)
Please note:
On 230 volt versions
connect 230Vac to
terminals L & N.
DIL Switch Settings (see rear of circuit board)
The DIL switch settings can be recorded on page 11.
On/O
Compressor Delay On
Not Used
4 Events Per Day
Chrono-proportional
Compressor Delay O
Not Used
2 Events Per Day
6
Installation Instructions
GB Fitting the Thermostat to the Wall
Ensure the unit is rmly in place.
Press the reset button. The unit is ready to programme.
Removing Battery Isolation Strip (Battery models)
Replacing the Batteries (Battery models)
7
Installation Instructions
GB
Installer Settings with Advanced Programming
The hardware settings with the HC6000 Heat/Cool thermostats
include the following:
Advanced Programming
Security Settings
Setting Record
Advanced Programming Options
Advanced programming allows the building owner to limit the
extent to which the user is able to programme or override the
settings.This may be done to protect the system from misuse or
to improve the energy eciency of the system.
To enter Advanced Programming
press and hold PROG, SELECT and
FAN for 2 seconds.
Please note:
- The thermostat will automatically exit from Advanced
Programming if no button is pushed within a two minute
period.
- To exit Advanced Programming repeatedly press the PROG
button to return the unit to RUN mode. (Time appears and
the colon in the display begins to ash).
++
PROG SELECT FAN
8
IMPORTANT: See Security Settings on page 10.
This feature allows the building
owner to disable all programming
functions and to limit the degree of
temperature override that the user
can select to ± 2°C.
The Keyboard Disable Function is
pre-set to OFF. If you would like to
disable the keyboard use the +or
-buttons until your preference is
selected.
When the keyboard is disabled the use of the or
temperature override buttons is limited to ± 2°C.
Press the PROG button to advance to the next setting option.
Installation Instructions
GB Setting the Keyboard Disable Function (option 1)
or
+-
The compressor time delay feature is only active if DIL switch 2
(compressor time delay) is set to enabled and is only available
on models with cooling output.
This feature allows the installer to
select the minimum compressor o
times. The compressor time delay
is preset to 2 minutes minimum o
time. Use the +or -buttons until
your preference is selected. The
options are 1, 2, 3, 4 or 5 minutes
minimum o time.
Press the PROG button to advance to the next setting option.
Setting Compressor Time Delay (option 2)
or
+-
9
This feature allows the installer to
select a timed fan overrun following
each cooling demand. The unit is
pre-set to o. Using the +or -buttons
select your preference from o, 30,
60 or 90 seconds.
Press the PROG button to advance to
the next setting option.
Setting Fan Run-On After Cooling (option 3)
or
+-
This feature allows the installer or
the building owner to determine
the minimum deadband between
heating and cooling. The unit is pre-
set to 2°C. Using the +or -buttons
select your preference from 1°C, 2°C,
3°C or 4°C.
Press the PROG button to advance to
the next setting option.
Setting Heating/Cooling Deadband (option 4)
or
+-
Installation Instructions
GB
10
This feature allows the installer to bias the
thermostat calibration and temperature
shown on the display. The unit is pre-set
to 0. Using the +or -buttons select your
preference. The options are + or - 3°C in
0.5°C increments.
Press the PROG button to return to RUN mode.
Setting Thermostat Calibration (option 5)
Installation Instructions
GB
or
+-
Security settings should be carried out at the last stage of the
commissioning process. This is an optional setting and need
only be carried out if the building owner wishes to prevent the
user from tampering with the thermostat programmes.
This is achieved by setting the
advanced programming option 1 to
keyboard disabled ON. This disables all
programming functions and limits the
temperature overrides to ± 2°C. All user features such as choice
of clock display (AM/PM or 24 hour), temperature scaling (°F
or °C) continue to be available to the user. To make the setting
refer to the setting the keyboard disable function paragraph on
page 8.
Security Settings
Ce manuel convient aux modèles suivants
5
Table des matières
Langues :
Autres manuels Danfoss Thermostat
Danfoss
Danfoss DEVIreg 532 Manuel utilisateur
Danfoss
Danfoss Icon Master Manuel utilisateur
Danfoss
Danfoss Icon Wireless Dial Manuel utilisateur
Danfoss
Danfoss TPOne-M Manuel utilisateur
Danfoss
Danfoss DEVI DEVIreg 532 Manuel utilisateur
Danfoss
Danfoss ECL Comfort 210 Manuel utilisateur
Danfoss
Danfoss RET 230 HCW-1 Manuel utilisateur
Danfoss
Danfoss DEVI DEVIreg 330 Manuel utilisateur
Danfoss
Danfoss TS715 Si Manuel utilisateur
Danfoss
Danfoss ECL Comfort 310, A376 Manuel utilisateur
Danfoss
Danfoss TP75H Manuel d'utilisation
Danfoss
Danfoss RET230P Manuel utilisateur
Danfoss
Danfoss ST-D1 Manuel utilisateur
Danfoss
Danfoss 3020P Instructions de montage
Danfoss
Danfoss Basic Plus2 Manuel utilisateur
Danfoss
Danfoss 100064 Manuel utilisateur
Danfoss
Danfoss TP5000-RF Mode d'emploi
Danfoss
Danfoss RMT-24 Manuel utilisateur
Danfoss
Danfoss DEVIreg 132 Manuel utilisateur
Danfoss
Danfoss LX205T Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
