Danfoss ECtemp 530 Manuel utilisateur
Danfoss ECtemp 530
Electronic Thermostat
Installation Guide
electricheating.danfoss.com
Danfoss ECtemp 530
3Installation Guide
1 Introduction
ECtemp 530 is an electronic thermostat provided with a
2- pole switch and a wire sensor to measure and control the
desired oor temperature. It can be either ush-mounted
(standard) or surface-mounted (using special box).
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 1 to 6 (each step corresponds
to approximately 8 °C). Furthermore, it has a LED indicator
showing standby periods (green light) and heating periods
(red light).
More information on this product can also be found at:
ectemp.danfoss.com
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Technical Specications . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . . 7
3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Disposal Instruction . . . . . . . . . . . . . . . . . 12
Danfoss ECtemp 530
Installation Guide4
1.1 Technical Specications
Operation voltage 220-240 V~, 50 Hz
Standby power consump-
tion Max 0.25 W
Relay:
Resistive load
Inductive load
Max 15 A / 3450 W @ 230 V
cos φ= 0.3 max 1A
Sensing units NTC 15kOhm at 25°C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0.4 °C
Ambient temperature -10 to +30 °C
Frost protection tempera-
ture 5 °C -
Temperature range ( ) 5-45°C with oor sen-
sor only
Cable specication max 1x4 mm² or 2x2,5 mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Danfoss ECtemp 530
5Installation Guide
Type 1C
Storage temperature -20 to +65 °C
IP class 31
Protection class Class II -
Dimensions 85 x 85 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard «Automatic
electrical controls for household and similar use»:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
Make sure the mains supply to the thermostat is turned o
before installation.
IMPORTANT: When the thermostat is used to control a
oor heating element in connection with a wooden oor or
similar material, always use a oor sensor and never set the
maximum oor temperature to more than 35 °C.
Danfoss ECtemp 530
Installation Guide6
Please also note the following:
• The installation of the thermostat must be done by an
authorized and qualied installer according to local
regulations.
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• The sensor is to be considered as live voltage. Have
this in mind if the sensor must be extended.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
Danfoss ECtemp 530
7Installation Guide
2 Mounting Instructions
Place the thermostat at a suitable height on
the wall (typically 80-170cm.).
In wet rooms, place the thermostat accord-
ing to local regulation on IP classes.
Note: A oor sensor enables a more accurate
temperature control and is recommended in
all oor heating applications and mandatory
under wooden oors to reduce the risk of
over-heating the oor.
• Place the oor sensor in a conduit in an appropriate
place where it is not exposed to sunlight or draft from
door openings.
• Equally distant and >2cm from two heating cables.
• The conduit should be ush with the oor surface -
countersink the conduit if necessary.
• Route the conduit to the connection box.
• The bending radius of the conduit must be min 50mm.
Danfoss ECtemp 530
Installation Guide8
Follow the steps below to mount the thermostat:
1. Open the thermostat:
devireg™550
3
5
6
24
20
30
40
50
• Press the release tab in the bottom of the ther-
mostat using a at object.
• Carefully detach the front cover.
• Carefully detach the frame.
Danfoss ECtemp 530
9Installation Guide
2. Connect the thermostat according to the connection
diagram.
IP31
-10T30
D530
Mains
220-240V~
Max. Load
15 (1) A
Sensor
NL NTC
N
LOAD
L
LOAD
-5°C
L
9
By connecting an external timer to the terminal
marked by a moon symbol (and by using for example
the same phase as for the mains power supply), the
thermostat can be set to reduce the temperature by
5 °C during specied periods.
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note: Always install the oor sensor in a conduit in
the oor.
Danfoss ECtemp 530
Installation Guide10
3. Mount and reassemble the thermostat.
• Fasten the thermostat to a socket or an exterior
wall box by driving the screws through the holes in
each side of the thermostat.
• Install the frame and front cover in the reverse
order of disassembly.
4. Turn on the power supply.
3 Settings
How to change the minimum and maximum oor
temperatures
1. Remove the adjust-
ment button.
2. Move the pins to the
desired positions.
3. Put the adjustment
button back in place.
devireg™550
3
5
6
24
20
30
40
50
Note: Please be aware of the following:
• The oor temperature is measured where the oor
sensor is placed.
• The temperature of the bottom of a wooden oor can
be up to 10 degrees higher than the top.
Autres manuels pour ECtemp 530
1
Table des matières
Autres manuels Danfoss Thermostat
Danfoss
Danfoss DEVIreg 330 Manuel utilisateur
Danfoss
Danfoss TP5000 si range Manuel utilisateur
Danfoss
Danfoss 088L5130 Manuel utilisateur
Danfoss
Danfoss Eco Manuel utilisateur
Danfoss
Danfoss living connect Z Manuel utilisateur
Danfoss
Danfoss TP4000 Range Manuel utilisateur
Danfoss
Danfoss Living Eco Manuel utilisateur
Danfoss
Danfoss 088U0212 Manuel utilisateur
Danfoss
Danfoss living connect Manuel utilisateur
Danfoss
Danfoss RET2000B-RF + RX1-S Manuel utilisateur
Danfoss
Danfoss TP6000M Manuel utilisateur
Danfoss
Danfoss TP7000 Series Manuel utilisateur
Danfoss
Danfoss DEVIreg 530 Manuel utilisateur
Danfoss
Danfoss TP75-RF Manuel utilisateur
Danfoss
Danfoss FH-WT Manuel utilisateur
Danfoss
Danfoss DEVIreg Smart Manuel utilisateur
Danfoss
Danfoss Icon Master Manuel utilisateur
Danfoss
Danfoss DEVIreg Opti Manuel utilisateur
Danfoss
Danfoss ECtemp 330 Manuel utilisateur
Danfoss
Danfoss CET2000B-RF Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
