Danfoss DEVIreg 532 Manuel utilisateur

www.DEVI.com

Installation Guide

DEVIreg™ 532

Electronic Thermostat

DEVIreg™ 532

Installation Guide 3

1 Introduction

DEVIreg™ 532 is an electronic thermostat provided with a

2-pole switch, a room sensor to control the room temperature,

and an additional oor sensor to limit the maximum oor tem-

perature. It can be either ush-mounted or surface-mounted.

The thermostat has a button for adjusting the temperature

setting with a scale from ( ) 5-35°C. Furthermore, it has

a LED indicator showing standby periods (green light) and

heating periods (red light).

More information on this product can also be found at:

devireg.devi.com

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Technical Specications . . . . . . . . . . . . 4

1.2 Safety Instructions . . . . . . . . . . . . . . . . 5

2 Mounting Instructions . . . . . . . . . . . . . . . . 6

3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 12

5 Disposal Instruction . . . . . . . . . . . . . . . . . . 14

DEVIreg™ 532

Installation Guide4

1.1 Technical Specications

Operation voltage 220-240 V~, 50 Hz

Standby power

consumption

Max 0.25 W

Relay:

Resistive load

Inductive load

Max 15 A / 3450 W @ 230 V

cos φ= 0.3 max 1 A

Sensing units NTC 15 kOhm at 25 °C

Sensing values:

0 °C

25 °C

50 °C

42 kOhm

15 kOhm

6 kOhm

Hysteresis ± 0.4 °C

Ambient temperature -10 to +30 °C

Frost protection

temperature

5 °C -

Temperature range 5-35 °C room temperature

20-50 °C oor temperature

limiter - default 35 °C

Cable specication max 1 x 4 mm² or 2 x 2,5 mm²

Ball pressure temperature 75 °C

Pollution degree 2 (domestic use)

DEVIreg™ 532

Installation Guide 5

Type 1C

Storage temperature -20 to +65°C

IP class 31

Protection class Class II -

Dimensions 85 x 85 x 36 mm

Weight 90 g

The product complies with the EN/IEC Standard «Automatic

electrical controls for household and similar use»:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1.2 Safety Instructions

Make sure the mains supply to the thermostat is turned o

before installation.

IMPORTANT: When the thermostat is used to control a

oor heating element in connection with a wooden oor or

similar material, always use a oor sensor and never set the

maximum oor temperature to more than 35°C.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualied installer according to local

regulations.

DEVIreg™ 532

Installation Guide6

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• The sensor is to be considered as live voltage. Have

this in mind if the sensor must be extended.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water,

dust, and excessive heat.

2 Mounting Instructions

Please observe the following placement guidelines:

Place the thermostat at a suitable height

on the wall (typically 80-170cm.).

In wet rooms, always place the thermostat

according to local regulation on IP classes.

Do not place the thermostat on the inner

side of an exterior wall.

DEVIreg™ 532

Installation Guide 7

Always install the thermostat at least 50 cm.

from windows and doors.

Do not place the thermostat in a way that

it will be exposed to direct sunlight.

Note: A oor sensor enables a more accurate

temperature control and is recommended

in all oor heating applications

and mandatory under wooden oors to

reduce the risk of over-heating the oor.

• Place the oor sensor in a conduit in an appropriate

place where it is not exposed to sunlight or draft from

door openings.

• Equally distant and >2cm from two heating cables.

• The conduit should be ush with the oor surface -

countersink the conduit if necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must be min 50mm.

DEVIreg™ 532

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

devireg™550

• Press the release tab in the bottom of the

thermostat using a at object.

• Carefully detach the front cover.

• Carefully detach the frame.

DEVIreg™ 532

Installation Guide 9

2. Connect the thermostat according to the connection

diagram.

IP31

-10T30

D532

Mains

220-240V~

Max. Load

15 (1) A

Sensor

NL NTC

LOAD

9еквонатсуоповтсдовокуР

The screen of the heating cable must be connected

to the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the oor sensor in a conduit in

the oor.

3. Set the maximum oor temperature between 20 °C

and 50 °C by turning the screw with temperature

indications in the upper left corner.

4. Mount and reassemble the thermostat:

• Fasten the thermostat to a ush-mounting box

or a surface-mounting box by driving the screws

through the holes in each side of the thermostat.

• Install the frame and front cover in the reverse

order of disassembly.

5. Turn on the power supply.

DEVIreg™ 532

Installation Guide10

3 Settings

How to change the minimum and maximum oor

temperatures

1. Remove the adjustment button.

2. Move the pins to the desired

positions.

3. Put the adjustment button back

in place.

devireg™550

Note: Please be aware of the following:

• The oor temperature is measured where the oor

sensor is placed.

• The temperature of the bottom of a wooden oor can

be up to 10 degrees higher than the top.

• Floor manufactures often specify the max

temperature on the top surface of the oor (usually

27-28 ˚C).

• By default, the maximum oor temperature is set to

35 °C.

• Always use a oor sensor or a room + oor sensor

combination to control oor heating. Without a oor

sensor, the temperature control may be less accurate

and you risk overheating the oor.

Table des matières

Autres manuels Danfoss Thermostat

Danfoss

Danfoss RT1 Instructions de montage

Danfoss

Danfoss Type CFR Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel utilisateur

Danfoss

Danfoss RET2001 Manuel utilisateur

Danfoss

Danfoss TP5001 series Instructions d'utilisation

Danfoss

Danfoss living connect Manuel utilisateur

Danfoss

Danfoss DEVI DEVIreg 330 Manuel utilisateur

Danfoss

Danfoss RET1001M Manuel utilisateur

Danfoss

Danfoss GreenCon RC-C2 Manuel utilisateur

Danfoss

Danfoss FH-CWP Manuel utilisateur

Danfoss

Danfoss Eco Manuel utilisateur

Danfoss

Danfoss TP5000 RF Si Manuel utilisateur

Danfoss

Danfoss RT 106 Manuel utilisateur

Danfoss

Danfoss ECtemp Next Plus HW Manuel utilisateur

Danfoss

Danfoss 088U0215 Manuel utilisateur

Danfoss

Danfoss ECtemp 532 Manuel utilisateur

Danfoss

Danfoss REP24CO Manuel utilisateur

Danfoss

Danfoss Eco Manuel utilisateur

Danfoss

Danfoss living connect Manuel utilisateur

Danfoss

Danfoss EFET 160 Manuel utilisateur

Danfoss

Danfoss 088U0212 Manuel utilisateur

Danfoss

Danfoss DEVIreg 330 Manuel utilisateur

Danfoss

Danfoss Link FT Manuel utilisateur

Danfoss

Danfoss 102E7 Instructions de montage

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur