Danfoss CET2000B-RF Manuel utilisateur

CET2000B-RF + RX1-S + CS2

Wireless Electronic Hot Water Cylinder Thermostat

Installation Guide

Danfoss Heating

CET2000BRF

For a large print version of these instructions

please call Marketing on 0845 121 7400.

Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other

printed material. All trademarks in this material are property of the respective companies.

Hearby, Danfoss A/S declares that the radio equipment type CET2000B-RF + RX1-S is in

compliance with directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address, http://heating.danfoss.co.uk/xdoccat/14_CATC-J_MNU17497125_SIT313.html

Danfoss Heating 3

Product Specications

CET2000B-RF RX1-S

Operating Voltage 2.5 – 3 VDC

(2xAA alkaline batteries) 230Vac 50Hz

Output Relay - 1 x SPDT Type 1B

Switch rating - 3A (1) at 230Vac

Output - Volt free

Setting temp. range 40-65°C -

Maximum ambient temp. 0-45°C

Battery lifetime 2 years -

Max. range 30 metres

Operating frequency 433.92MHz <1mW ERP

IP Rating IP20 IP40

Control On-O

Operating mode Domestic Hot Water Heating

Construction EN 60730-2-9 EN 60730-1

Control pollution situation Degree 2

Rated impulse voltage - 2.5kV

Ball pressure test 75°C

Dimensions H84 x W84 x D35 H84 x W84 x D28

Software classication A

Important note RF products: Ensure that there are no large metal objects, such as

boiler cases or other large appliances, in line of sight between the transmitter and

receiver as these will prevent communication between thermostat and receiver.

CET2000B-RF

1. The clamp on sensor should

be mounted onto the

cylinder wall at a height

equivalent to ½ the height

of the cylinder. Care should

be taken to remove any

insulation material from

the cylinder and to ensure

that the copper surface of

the cylinder is clean. See

diagram opposite for details.

This product should only be installed by a qualied

electrician or competent heating installer, and must be

in accordance with local wiring regulations.

1/2 c

ylinder

height

For insulation thicker than 25mm

and up to 55mm thick, use the

extra cover supplied as a spacer to

ensure that the sensor is held in

firm contact with the cylinder wall.

Installation

Danfoss Heating 5

2. Before attaching the sensor to the cylinder using the strap

provided, connect a 2-core cable to the sensor to allow

interconnection to the thermostat setting unit.

3. Apply the contact paste provided to the part of the sensor

in contact with the cylinder and clamp the sensor to the

cylinder wall.

A spacer piece is provided for use with cylinders that have

thick insulation (see page 6).

4. Mount the thermostat wallplate on to a wall next to the

cylinder. Connect the cable from the sensor to terminals 1

& 2 of the wallplate (see wiring diagram on page 7).

5. Now mount the thermostat setting unit onto the wallplate

(see diagrams on page 9).

CET2000B-RF

1/2 cylinder

height

For insulation thicker than 25mm

and up to 55mm thick, use the

extra cover supplied as a spacer to

ensure that the sensor is held in

rm contact with the cylinder wall.

Danfoss Heating 7

Sensor Wiring

CS2

sensor

1 2 3

CET2000B-RF

Cable specication: minimum cross section 0.5mm2

CET2000B-RF

Installation - RX1-S Receiver unit

ELECTRONICS

234

COM ON OFF

230Vac

Please Note: This product should only be installed by a

qualied electrician or competent heating installer, and must

be in accordance with local wiring regulations.

Danfoss Heating 9

Mounting - CET2000B-RF

CET2000B-RF

Hard Wired Heating with Wireless Hot Water

Control, 3 Port Mid-Position Valve

ELECTRONICS

NL123

ELECTRONICS

NL2

HTG OFF 3

HW ON 4

HTG ON

230Vac

HW OFF

RET1000MS

Room Thermostat

RX1-S Receiver -

paired to CET2000B-RF

FP715 Programmer

3 Port Mid-Position Valve

FP715 Programmer

Boiler

Pump

NL2

blue

brown/

white

orange

grey

N L N L SW.L

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Danfoss Thermostat

Danfoss

Danfoss RET B Mode d'emploi

Danfoss

Danfoss TP4 Mode d'emploi

Danfoss

Danfoss TS715 Si Manuel utilisateur

Danfoss

Danfoss SET 3E Manuel utilisateur

Danfoss

Danfoss TPOne-M Manuel utilisateur

Danfoss

Danfoss RET1000 B Manuel utilisateur

Danfoss

Danfoss CET B-RF Mode d'emploi

Danfoss

Danfoss EFIT 550 Manuel utilisateur

Danfoss

Danfoss Devireg 535 Instructions d'utilisation

Danfoss

Danfoss HP8211-1RJ Manuel utilisateur

Danfoss

Danfoss TP75H Manuel d'utilisation

Danfoss

Danfoss ECA 30 Manuel utilisateur

Danfoss

Danfoss Living Eco Manuel utilisateur

Danfoss

Danfoss ORT-01 Manuel utilisateur

Danfoss

Danfoss Link FT Manuel utilisateur

Danfoss

Danfoss TP5001 series Manuel utilisateur

Danfoss

Danfoss ECL Comfort 310, A333 Manuel utilisateur

Danfoss

Danfoss CET2000B-RF + RX1-S + CS2 Manuel utilisateur

Danfoss

Danfoss MBC 8000 Manuel utilisateur

Danfoss

Danfoss BasicPlus2 WT-DM Manuel utilisateur

Danfoss

Danfoss TP4000 Range Manuel utilisateur

Danfoss

Danfoss ECtemp 531 Manuel utilisateur

Danfoss

Danfoss RMT-24 Manuel utilisateur

Danfoss

Danfoss RTW-RA Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur